☆ 4.8 Article

Real-time structural validation for material extrusion additive manufacturing

ADDITIVE MANUFACTURING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Composites

Effect of Defects Part I: Degradation of Constitutive Coefficients as an Input to the Composite Failure Model with Microvoids and Porosity

Vahid Tavaf et al.

Summary: This article presents a guideline for appropriately degrading each coefficient using quantified perturbation in composite materials and explores the distribution of effective material properties (EMPs) under different defect states. The study finds that EMPs degrade even with a small percentage of void content, and the degradation of constitutive coefficients follows a definitive pattern.

JOURNAL OF COMPOSITES SCIENCE (2022)

添加到收藏夹

Article Mechanics

Effect of the manufacturing parameters on the tensile and fracture properties of FDM 3D-printed PLA specimens

Liviu Marsavina et al.

Summary: This study investigates the influence of manufacturing parameters on the tensile and fracture properties of PLA elements obtained by FDM technology. The results show that the performance of FDM 3D-printed PLA specimens is dependent on the manufacturing parameters.

ENGINEERING FRACTURE MECHANICS (2022)

添加到收藏夹

Article Automation & Control Systems

Vision-based real-time monitoring of extrusion additive manufacturing processes for automatic manufacturing error detection

Paschalis Charalampous et al.

Summary: This paper introduces a vision-based method to evaluate the performance of additive manufacturing by comparing physical printed parts with digital 3D models in real-time, addressing issues with defect detection and dimensional accuracy inspection.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

The influence of porosity, crystallinity and interlayer adhesion on the tensile strength of 3D printed polylactic acid (PLA)

Natalia von Windheim et al.

Summary: The study aims to investigate the impact of printing parameters and annealing on porosity, crystallinity, and tensile strength of 3D printed PLA. Results show that annealing above T-cc increases crystallinity without significantly affecting porosity, while annealing below T-cc improves tensile strength. The study highlights the importance of co-crystallization across weld interfaces for increasing strength and utilizes AFM to observe morphology at the weld.

RAPID PROTOTYPING JOURNAL (2021)

添加到收藏夹

Article Materials Science, Composites

Effect of Defects Part II: Multiscale Effect of Microvoids, Orientation of Rivet Holes on the Damage Propagation, and Ultimate Failure Strength of Composites

Vahid Tavaf et al.

Summary: The study showed that microscale defects near cutouts have a significant impact on macroscale damage propagation in composite materials. Both experimental and numerical results confirmed that the strength of the horizontal configuration with two holes was higher than the vertical configuration, and the square configuration was stronger than the diamond configuration.

JOURNAL OF COMPOSITES SCIENCE (2021)

添加到收藏夹

Article Materials Science, Composites

Tensile and Compressive Behavior in the Experimental Tests for PLA Specimens Produced via Fused Deposition Modelling Technique

Salvatore Brischetto et al.

JOURNAL OF COMPOSITES SCIENCE (2020)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Detecting cyber-physical attacks in CyberManufacturing systems with machine learning methods

Mingtao Wu et al.

JOURNAL OF INTELLIGENT MANUFACTURING (2019)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Data fusion and machine learning for industrial prognosis: Trends and perspectives towards Industry 4.0

Alberto Diez-Olivan et al.

INFORMATION FUSION (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

The impact of defects on tensile properties of 3D printed parts manufactured by fused filament fabrication

Kazem Fayazbakhsh et al.

MATERIALS TODAY COMMUNICATIONS (2019)

添加到收藏夹

Article Engineering, Manufacturing

Autonomous in-situ correction of fused deposition modeling printers using computer vision and deep learning

Zeqing Jin et al.

MANUFACTURING LETTERS (2019)

添加到收藏夹

Review Computer Science, Information Systems

Edge Computing: A Survey On the Hardware Requirements in the Internet of Things World

Maurizio Capra et al.

FUTURE INTERNET (2019)

添加到收藏夹

Article Engineering, Mechanical

An insight to the failure of FDM parts under tensile loading: finite element analysis and experimental study

Ashu Garg et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

添加到收藏夹

Proceedings Paper Automation & Control Systems

The role of additive manufacturing in the era of Industry 4.0

Ugur M. Dilberoglu et al.

27TH INTERNATIONAL CONFERENCE ON FLEXIBLE AUTOMATION AND INTELLIGENT MANUFACTURING, FAIM2017 (2017)

添加到收藏夹

Review Pharmacology & Pharmacy

Physical and mechanical properties of PLA, and their functions in widespread applications - A comprehensive review

Shady Farah et al.

ADVANCED DRUG DELIVERY REVIEWS (2016)

添加到收藏夹

Article Psychology, Multidisciplinary

Evidence accumulator or decision threshold - which cortical mechanism are we observing?

Patrick Simen

FRONTIERS IN PSYCHOLOGY (2012)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.