☆ 4.7 Article

Study on segregation solidification and homogenization behavior of Cu-16Sn-0.3Ti alloy powders

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Dependence of grain size on grain boundary diffusion mechanism of Nd-Fe-B sintered magnets

Sangen Luo et al.

Summary: This paper investigates the effect of grain size in the diffusion matrix on the grain boundary diffusion mechanism of Tb element. The results show that with only 0.75 wt. % TbF3 diffusion, the intrinsic coercivity increases significantly for the magnet with finer average grain size compared to the coarse-grain magnet. The increase in intrinsic coercivity is attributed to the increase in defect density and the higher grain orientation caused by grain refinement, which leads to improved diffusion efficiency and magnetic properties.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

Solid solubility extension and nano-mechanical properties of rapidly solidified Fe-Zr eutectic alloys under free fall condition

D. D. Zuo et al.

Summary: The liquid-solid phase transitions and solidified microstructures of highly undercooled Fe-Zr eutectic melts were investigated by the drop tube technique. Quantitative relationships among droplet diameter, undercooling, and cooling rate were calculated for different eutectic alloys. The evolution of solidified microstructure with droplet diameter was studied, showing changes in the microstructural morphology and solid solubility, affecting the nano-mechanical properties of the alloys.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hot isostatic pressing of Cu-15Ni-8Sn alloy with suppressed Sn macro-segregation and enhanced mechanical properties

Jikang Li et al.

Summary: The use of hot isostatic pressing (HIP) technique in the fabrication of Cu-15Ni-8Sn alloy helps alleviate or eliminate macro-segregation and coarse grains issues, resulting in nearly fully dense samples with simultaneous strength-plasticity enhancement.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Chemistry, Physical

Microstructure evolution and mechanical property of quaternary Cu-7%Al-4%Ni-2.5%Mn alloy solidified within ultrasonic field

X. Wang et al.

Summary: The application of power ultrasound during the solidification process of Cu-7%Al-4%Ni-2.5%Mn alloy significantly improves nucleation rate, leading to the formation of equiaxed grains with uniform solute distribution and a threefold increase in compressive yield strength. Additionally, the ultrasonic wave enhances the wetting effect between alloy melt and impurities, breaks dendrites into fragments, and promotes symmetrical distribution of temperature, solute, and flow fields in the solidification front.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Engineering, Mechanical

Selective laser melting of Cu-Ni-Sn: A comprehensive study on the microstructure, mechanical properties, and deformation behavior

Chao Zhao et al.

Summary: A comprehensive understanding of the deformation behavior and strengthening mechanism of the selective laser melted (SLM) alloy is crucial for maximizing the potential of the SLM process. This study focuses on the impact of SLM on the microstructure, deformation behavior, and mechanical properties of Cu-Ni-Sn alloy compared to their cast counterparts (CC). The SLM microstructure, characterized by increased dislocation density, offers a superior combination of tensile strength and ductility, mainly attributed to grain refinement, dispersed precipitation, and increased dislocation density.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Austenite Grain Refinement and Subsequent Martensite Transformation of Ternary Cu-Al-Ni Alloy Solidified Within Ultrasonic Field

Y. J. Hu et al.

Summary: The application of power ultrasound during the solidification of Cu-14wt pct Al-4.5 wt pct Ni alloy promoted the nucleation of primary austenite and influenced martensite transformation during subsequent quenching. The refinement of martensite phases and increase of beta 1' phase content due to ultrasound led to enhanced mechanical properties of the alloy, including increased yield strength, microhardness, and storage modulus.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Solidification Behavior of in situ TiB2/Cu Composite Powders during Reactive Gas Atomization

Jiang Yihui et al.

Summary: The TiB2/Cu composite powders fabricated in situ by reactive gas atomization exhibit high sphericity and a range of powder sizes. The morphology of the Cu matrix and the distribution of the TiB2 particles vary with the powder size. Interface morphologies in the composite powders undergo critical transitions at smaller sizes, influenced by the TiB2 particles and cooling rates.

JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION (2021)

添加到收藏夹

Article Engineering, Chemical

Atomization simulation and preparation of 24CrNiMoY alloy steel powder using VIGA technology at high gas pressure

Mingwei Wei et al.

POWDER TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Chemical

Effects of plasma rotating electrode process parameters on the particle size distribution and microstructure of Ti-6Al-4 V alloy powder

Yujie Cui et al.

POWDER TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Insight into the effect of Ti-addition on diffusion-controlled growth and texture of Nb3Sn intermetallic superconductor phase

S. Santra et al.

MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and tribological properties of plasma sprayed Cu-15Ni-8Sn coatings

Jin-Kun Xiao et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Nuclear Science & Technology

Development of the bronze processed Nb3Sn multifilamentary wires using Cu-Sn-Zn ternary alloy matrix

Yoshimitsu Hishinuma et al.

FUSION ENGINEERING AND DESIGN (2017)

添加到收藏夹

Review Physics, Applied

A review and prospects for Nb3Sn superconductor development

Xingchen Xu

SUPERCONDUCTOR SCIENCE & TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of atomization pressure on the breakup of TA15 titanium alloy powder prepared by EIGA method for laser 3D printing

Mingwei Wei et al.

VACUUM (2017)

添加到收藏夹

Article Engineering, Electrical & Electronic

Nb3Sn High Field Magnets for the High Luminosity LHC Upgrade Project

Giorgio Ambrosio

IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Additive manufacturing of Cu-10Sn bronze

S. Scudino et al.

MATERIALS LETTERS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Finite element analysis of the grain size effect on diffusion in polycrystalline materials

V. Lacaille et al.

COMPUTATIONAL MATERIALS SCIENCE (2014)

添加到收藏夹

Article Chemistry, Physical

The Cu-Sn phase diagram, Part I: New experimental results

S. Fuertauer et al.

INTERMETALLICS (2013)

添加到收藏夹

Article Multidisciplinary Sciences

Abnormal Grain Growth Induced by Cyclic Heat Treatment

Toshihiro Omori et al.

SCIENCE (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Grain size and grain-boundary effects on diffusion and trapping of hydrogen in pure nickel

A. Oudriss et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Engineering, Electrical & Electronic

Development of high Sn content bronze processed Nb3Sn superconducting wire for high field magnets

T Miyazaki et al.

IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.