☆ 4.7 Article

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Jiaguo Tang et al.

Summary: In this study, isothermal compression tests were conducted on the 2195 Al-Cu-Li alloy to investigate its hot deformation behavior. A processing map was established to predict the workability under different conditions, and the corresponding microstructures were analyzed to reveal the deformation mechanisms. The results indicate that the optimal hot-working conditions for the alloy are at temperatures of 460-500 degrees C and strain rates of 10-3-10-2 s-1, with dominant mechanisms of dynamic recrystallization and dynamic recovery.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

An optimized constitutive model and microstructure characterization of a homogenized Al-Cu-Li alloy during hot deformation

Shuai Long et al.

Summary: The flow behavior and thermal expansion behavior of a homogenized Al-Cu-Li alloy were investigated through quenching expansion tests and isothermal compression tests. It was found that the temperature rise dissolves coarse secondary phases and increases the coefficient of thermal expansion. Different constitutive models were evaluated, with the two-step optimized Johnson-Cook model showing the highest precision in predicting the material behavior.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behaviors of AZ91 magnesium alloy: Constitutive equation, ANN-based prediction, processing map and microstructure evolution

Dongxiao Wang et al.

Summary: The hot deformation behavior of an AZ91 magnesium alloy was studied using the Arrhenius model and Back-Propagation Artificial Neural Network (BP-ANN) approaches. The results showed that the BP-ANN model had higher accuracy compared to the Arrhenius model. The processing map was divided into three parts: machinable area, instability area I, and instability area II. The instability mode in areas B and C changed from cracks to holes with increasing temperature or decreasing strain rate. Stable hot-deformation conditions were found in specific ranges of temperature and strain rate.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A modified Arrhenius constitutive model of 2219-O aluminum alloy based on hot compression with simulation verification

Hao Wang et al.

Summary: In this study, the flow stress data of 2219-O aluminum alloy were obtained through hot compression tests, and four different constitutive models were established and evaluated for their prediction accuracy. A newly modified constitutive model was proposed, which had a simpler structure and accurately predicted the evolution behavior of flow stress.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior, processing map, microstructure evolution and dynamic recrystallization mechanism of Mg-5Al-0.6Sc alloy

Lei Zhang et al.

Summary: This study investigated the effect of deformation temperature and strain rate on the hot deformation mechanism of an as-cast Mg-5Al-0.6Sc alloy. The results showed that the flow stress decreased with increasing temperature and decreasing strain rate. A constitutive equation was established to accurately predict the hot deformation behavior of the alloy. The optimal processing area was determined based on processing maps, and the microstructure evolution and dynamic recrystallization mechanism of the alloy were analyzed.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Improving mechanical properties of a cast Al-Mg alloy with high Mg content by rapid solidification

Xinbiao Wang et al.

Summary: This research aims to reduce the amount and size of Al-Mg intermetallic phases by rapid solidification and improve the strength and ductility of a cast Al-15 wt% Mg alloy. The results show that the alloy processed by twin-roll casting (TRC) has refined Al grains and refined granular Al3Mg2 particles, as well as increased Mg solid solubility and decreased amount of Al3Mg2 phase. The TRC Al-15 wt% alloy exhibits higher yield strength, ultimate tensile strength, and uniform elongation compared to the conventionally mold cast counterpart.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A comparative study on modified and optimized Zerilli-Armstrong and arrhenius-type constitutive models to predict the hot deformation behavior in 30Si2MnCrMoVE steel

Fan Li et al.

Summary: The elevated temperature flow behaviors of 30Si2MnCrMoVE low-alloy ultra-high strength steel were studied through hot compressive deformation tests and the establishment of constitutive equations. It was found that the modified ZA model was not accurate in describing the flow behavior, while the Arrhenius type model had the highest prediction accuracy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural evolution and mechanical behaviour in the hot deformation of GH3128 alloy

Yongdi Wang et al.

Summary: This study investigates the microstructural evolution and mechanical behavior of the GH3128 alloy during hot deformation. The results show that the precipitation of the second phase in the grain boundary increases with temperature, and dynamic recrystallization occurs through twin-induced and particle-stimulated nucleation. The mechanical behavior varies with temperature, with a decrease in elongation and a change in fracture mechanism from ductile to ductile brittle fracture at higher temperatures. These findings provide a theoretical basis and guidance for the hot-working process of GH3128.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Constitutive modeling and hot deformation processing map of a new biomaterial Ti-14Cr alloy

Sumit Ghosh et al.

Summary: The present study designed a new biomaterial Ti-14Cr alloy for biomedical applications and investigated its manufacturing process through hot deformation. A processing map was constructed to evaluate the hot workability and deformation mechanisms of the alloy at different temperature and strain rate ranges. The study identified the optimal parameters for hot deformation and established a mathematical relation to elucidate the influence of true strain on material constants. The research provides important insights for optimizing the hot deformation parameters and controlling the grain structure of the alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Editorial Material Materials Science, Multidisciplinary

Constitutive modeling and dynamic recrystallization mechanism elaboration of FGH96 with severe hot deformation

Chang-an Li et al.

Summary: This paper conducted hot compression experiments to analyze the deformation behavior and dynamic recrystallization of FGH96 at high temperature and strain rate conditions. Two strain modified viscoplastic constitutive models were established and proven to accurately reflect the deformation behavior and suitable for numerical simulation of IFW.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior of an extruded AZ31 alloy doped with rare-earth elements

A. Sheikhani et al.

Summary: The study investigated the hot deformation behavior of an extruded Mg-3 wt% Al-1 wt% Zn (AZ31) alloy with and without rare-earth (RE) elements. It was found that the addition of RE elements enhanced the plasticity of the alloy and reduced the instability region according to the processing maps.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of cold temperatures, strain rates and anisotropy on the mechanical behavior and fracture morphology of an Al-Zn-Mg-Cu alloy

Yue Guo et al.

Summary: Tensile experiments were conducted on Al-Zn-Mg-Cu alloy at various temperatures and strain rates, revealing an increase in peak stress with decreasing temperature and different stress responses for specimens from different orientations. The coupling effects of dynamic strain aging and work hardening influenced the strain rate sensitivity value. Fracture morphologies observed by SEM showed ductile fracture mode at room temperature and brittle-ductile mixed fracture mode at below-zero temperatures, with anisotropy discussed in detail.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot deformation and dynamic recrystallization in Al-Mg-Si alloy

Jiachen Li et al.

Summary: The hot deformation behavior of Al-Mg-Si alloys was studied through isothermal compression tests, revealing that the dynamic recrystallization mechanism depends on the Zener-Hollomon values. Three different DRX mechanisms were observed during the experimental process.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dynamic softening mechanisms and Zener-Hollomon parameter of Al-Mg-Si-Ce-B alloy during hot deformation

Yi Yu et al.

Summary: Isothermal hot compression tests were conducted on Al-Mg-Si-Ce-B alloy at temperatures from 623-823 K with strain rates of 0.01-50 s-1. The alloy showed plastic deformation instability at relatively low temperatures, with optimized deformation parameters identified as 783-823 K/0.03-0.04 s. The microstructure was characterized using TEM and EBSD, and the influence of Z parameter on dynamic softening mechanisms was discussed, showing both DRV and CDRX as softening mechanisms during hot deformation.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Chemistry, Physical

Effect of Zener-Hollomon parameter on the flow behavior of Zr-based metallic glass

Z. F. Yao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and 3D processing maps of AA7020 aluminum alloy

Bin Ke et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution of annealed 7075 aluminum alloy and its influence on room-temperature plasticity

Lin Hua et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot Deformation Behavior and Dynamic Recrystallization Kinetics of a Novel Sc and Zr Modified Ultra-high-strength Al-Zn-Mg-Cu Alloy

B. Li et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Research on dynamic recrystallization behavior of Ni-Fe-Cr based alloy

Bo Li et al.

MATERIALS CHARACTERIZATION (2020)

添加到收藏夹

Article Chemistry, Physical

Constitutive modeling, processing map establishment and microstructure analysis of spray deposited Al-Cu-Li alloy 2195

Yongxiao Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

The effect of hot form quench (HFQ®) conditions on precipitation and mechanical properties of aluminium alloys

Kailun Zheng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Constitutive modeling of flow stress during hot deformation of Sn-Al-Zn-Cu-Mg multi-principal-element alloy

Hasti Khodashenas et al.

VACUUM (2019)

添加到收藏夹

Article Engineering, Civil

A study of interfacial heat transfer and its effect on quenching when hot stamping AA7075

Wenchao Xiao et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot deformation behavior and microstructure of strain compression AA2195 alloy under plane

Qingbo Yang et al.

MATERIALS CHARACTERIZATION (2017)

添加到收藏夹

Review Materials Science, Multidisciplinary

A review of dynamic recrystallization phenomena in metallic materials

K. Huang et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot deformation behavior and constitutive modeling of homogenized 6026 aluminum alloy

Liang Chen et al.

MATERIALS & DESIGN (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

A physically-based constitutive model for a typical nickel-based superalloy

Y. C. Lin et al.

COMPUTATIONAL MATERIALS SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Constitutive relationship for high temperature deformation of powder metallurgy Ti-47Al-2Cr-2Nb-0.2W alloy

Xiao-peng Liang et al.

MATERIALS & DESIGN (2012)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties of back extruded 7075 aluminum alloy at elevated temperatures

M. R. Rokni et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tensile and impact-toughness behaviour of cryorolled Al 7075 alloy

P. Das et al.

MATERIALS & DESIGN (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Constitutive descriptions for hot compressed 2124-T851 aluminum alloy over a wide range of temperature and strain rate

Y. C. Lin et al.

COMPUTATIONAL MATERIALS SCIENCE (2010)

添加到收藏夹

Article Chemistry, Physical

Microstructure and texture evolution in cryorolled Al 7075 alloy

R. Jayaganthan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

添加到收藏夹

Review Engineering, Industrial

A review on hot stamping

H. Karbasian et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

A comparative study on Johnson Cook, modified Zerilli-Armstrong and Arrhenius-type constitutive models to predict elevated temperature flow behaviour in modified 9Cr-1Mo steel

Dipti Samantaray et al.

COMPUTATIONAL MATERIALS SCIENCE (2009)

添加到收藏夹

Article Engineering, Mechanical

Forming of aluminum alloys at elevated temperatures - Part 1: Material characterization

N Abedrabbo et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.