☆ 4.5 Article

In Situ Wire plus Powder Synchronous Arc Additive Manufacturing of Ti-Cu Alloys

3D PRINTING AND ADDITIVE MANUFACTURING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Monitoring and flaw detection during wire-based directed energy deposition using in-situ acoustic sensing and wavelet graph signal analysis

Benjamin Bevans et al.

Summary: The aim of this study is to detect flaw formation in the wire-based directed energy deposition (W-DED) process using in-situ sensor data. The W-DED is similar to metal inert gas electric arc welding. The study develops and applies a novel wavelet integrated graph theory approach to detect flaw formation in W-DED parts using data acquired from an acoustic sensor. The approach achieves a false alarm rate of less than 2% in detecting the onset of various types of flaws.

MATERIALS & DESIGN (2023)

添加到收藏夹

Article Engineering, Manufacturing

Wire-powder-arc additive manufacturing: A viable strategy to fabricate carbide ceramic/aluminum alloy multi-material structures

Jianxin Sun et al.

Summary: This study developed a low-cost method, wire-powder-arc additive manufacturing (WPA-AM), to selectively reinforce aluminum matrix composites (AMCs) with ceramic particles. The effects of different ceramic particles on the properties and morphology of the composites were investigated. Additionally, the mechanical properties of different composite structures were compared.

ADDITIVE MANUFACTURING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Research on plasma arc additive manufacturing of Inconel 625 Ni-Cu functionally graded materials

Yanhu Wang et al.

Summary: In this study, a plasma arc additive manufacturing technique with a double-wire feedback mechanism was used to produce Inconel 625 Ni-Cu functionally graded materials. The microstructure, mechanical properties, and corrosion resistance of the manufactured alloy were evaluated. The results showed that the addition of Cu improved the microstructure and mechanical properties of the material, but had a negative impact on its corrosion resistance.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wire and arc additive manufacturing of 316L stainless steel/Inconel 625 functionally graded material: development and characterization

Tiago A. Rodrigues et al.

Summary: In this study, a functionally graded material (FGM) of 316L stainless steel to Inconel 625 was built using Twin-Wire and Arc Additive Manufacturing (T-WAAM) with different deposition strategies. The properties of the FGM were found to be superior with a direct interface, showing higher strengths and elongations upon failure, as well as lower residual stresses.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Engineering, Manufacturing

Wire-based directed energy deposition of NiTiTa shape memory alloys: Microstructure, phase transformation, electrochemistry, X-ray visibility and mechanical properties

Xinde Zuo et al.

Summary: This study demonstrates the use of WAAM technology for fabricating NiTiTa shape memory alloys, with the addition of Ta significantly enhancing corrosion resistance and X-ray visibility. The material shows promising potential for biomedical applications.

ADDITIVE MANUFACTURING (2022)

添加到收藏夹

Article Engineering, Manufacturing

Controlling the columnar-to-equiaxed transition during Directed Energy Deposition of Inconel 625

S. Li et al.

Summary: The grain orientation and mechanical properties of Inconel 625 can be tailored by adjusting the process parameters. Increasing the current during directed energy deposition promotes the transition from columnar to equiaxed grains. The solidification conditions and mechanical properties were characterized and compared, revealing that samples with equiaxed grains have higher yield strength.

ADDITIVE MANUFACTURING (2022)

添加到收藏夹

Article Engineering, Manufacturing

Influence of Silicon and Magnesium on the Mechanical Properties of Additive Manufactured Cu-Al Alloy

Yanhu Wang et al.

Summary: The study investigates the effects of using cold metal transfer technique to manufacture Cu-Al alloys with addition of silicon and magnesium. It was found that the addition of Si and Mg can improve the strength and ductility of the alloys, while heat treatments can enhance the strength properties but reduce the ductility of the alloys. The correlation between microstructure and mechanical properties of the additively manufactured alloys is discussed in the article.

3D PRINTING AND ADDITIVE MANUFACTURING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Huiting Zheng et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Biophysics

Biocompatibility, osseointegration, antibacterial and mechanical properties of nanocrystalline Ti-Cu alloy as a new orthopedic material

S. Moniri Javadhesari et al.

COLLOIDS AND SURFACES B-BIOINTERFACES (2020)

添加到收藏夹

Review Materials Science, Multidisciplinary

Progress in additive manufacturing on new materials: A review

Neng Li et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Chemistry, Physical

In-situ wire-feed additive manufacturing of Cu-Al alloy by addition of silicon

Yanhu Wang et al.

APPLIED SURFACE SCIENCE (2019)

添加到收藏夹

Article Electrochemistry

Passivity of titanium: part II, the defect structure of the anodic oxide film

Bumwook Roh et al.

JOURNAL OF SOLID STATE ELECTROCHEMISTRY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Microstructural characterization and enhanced hardness, wear and antibacterial properties of a powder metallurgy SiC/Ti-Cu nanocomposite as a potential material for biomedical applications

S. Moniri Javadhesari et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Optimization of mechanical property, antibacterial property and corrosion resistance of Ti-Cu alloy for dental implant

Jiewen Wang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Multidisciplinary Sciences

Additive manufacturing of ultrafine-grained high-strength titanium alloys

Duyao Zhang et al.

NATURE (2019)

添加到收藏夹

Review Materials Science, Multidisciplinary

Metal Alloys for Fusion-Based Additive Manufacturing

Duyao Zhang et al.

ADVANCED ENGINEERING MATERIALS (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

Additive manufacturing of multi-material structures

Amit Bandyopadhyay et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2018)

添加到收藏夹

Review Engineering, Manufacturing

A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement

Bintao Wu et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

添加到收藏夹

Review Engineering, Manufacturing

Invited review article: Strategies and processes for high quality wire arc additive manufacturing

C. R. Cunningham et al.

ADDITIVE MANUFACTURING (2018)

添加到收藏夹

Article Chemistry, Physical

Wear performance of novel nanostructured Ti-Cu intermetallic alloy as a potential material for biomedical applications

M. R. Akbarpour et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication of Copper-Rich Cu-Al Alloy Using the Wire-Arc Additive Manufacturing Process

Bosheng Dong et al.

METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Rapid quenching of semisolid Ti-Cu alloys: Insights into globular microstructure formation and coarsening

K. N. Campo et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Cu content on wear resistance and mechanical behavior of Ti-Cu binary alloys

Feifei Yu et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Additive manufacturing of metals

Dirk Herzog et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Materials Science, Biomaterials

Effect of the existing form of Cu element on the mechanical properties, bio-corrosion and antibacterial properties of Ti-Cu alloys for biomedical application

Erlin Zhang et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wire plus Arc Additive Manufacturing

S. W. Williams et al.

MATERIALS SCIENCE AND TECHNOLOGY (2016)

添加到收藏夹

Article Optics

Microstructural study of MMC layers produced by combining wire and coaxial WC powder feeding in laser direct metal deposition

Fuquan Li et al.

OPTICS AND LASER TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of composition and heat treatment on the mechanical behavior of Ti-Cu alloys

Alexandra O. F. Hayama et al.

MATERIALS & DESIGN (2014)

添加到收藏夹

Article Materials Science, Biomaterials

Effect of Cu content on the antibacterial activity of titanium-copper sintered alloys

Jie Liu et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2014)

添加到收藏夹

Article Engineering, Manufacturing

Laser Deposition of Ti-6Al-4V Wire with WC Powder for Functionally Graded Components

P. K. Farayibi et al.

MATERIALS AND MANUFACTURING PROCESSES (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

The Interdependence Theory: The relationship between grain formation and nucleant selection

D. H. StJohn et al.

ACTA MATERIALIA (2011)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.