☆ 4.6 Article

The Influence of Oscillation Parameters on the Formation of Overhead Welding Seams in the Narrow-Gap GMAW Process

APPLIED SCIENCES-BASEL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Manufacturing

Weld formation, arc behavior, and droplet transfer in narrow-gap laser-arc hybrid welding of titanium alloy

Jie Yu et al.

Summary: This study investigated the weld formation, arc behavior, and droplet transfer in narrow-gap laser-arc hybrid welding of 16 mm-thick TC4 titanium alloy. The penetration depth was influenced by laser power and welding speed, while filler metal height and sidewall penetration were proportional to wire feeding speed. Weld cross-sectional morphologies were classified into inclined, concave, and convex shapes. The optimization of laser power and wire feeding speed improved arc stability.

JOURNAL OF MANUFACTURING PROCESSES (2023)

添加到收藏夹

Article Automation & Control Systems

Analysis of metal transfer and weld forming characteristics in triple-wire gas indirect arc welding

Liming Liu et al.

Summary: Triple-wire gas indirect arc welding (TW-GIA) has the advantages of low heat input and high deposition rate. This study explores the metal transfer mode of TW-GIA using high-speed camera systems and electrical signal acquisition sensors. Four different metal transfer modes were identified, and their corresponding process parameter ranges were summarized. The SPT and SST modes were found to produce desirable weld seam due to their stable arc and uniform metal transfer process. TW-GIA also offers benefits such as small welding deformation, narrow heat-affected zone, and grain refinement.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Article Thermodynamics

Effect of molten pool behaviors on welding defects in tandem NG-GMAW based on CFD simulation

Siyuan Han et al.

Summary: The relationship between molten pool behaviors and weld bead formation under different wire feed rates and welding speeds was studied using a computational fluid dynamics model. The results showed that low wire feed rates or high welding speeds can result in lack-of-fusion or finger penetration defects. The simulation results indicated that vortex flows on the sidewalls enhance the transverse transmission of fluid and heat, leading to the formation of a concave weld bead. Additionally, low wire feed rates or high welding speeds weaken the transverse flow in the molten pool, hindering the melting of groove sidewalls and the spreading of liquid metal.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2022)

添加到收藏夹

Article Engineering, Manufacturing

Porosity suppressing and grain refining of narrow-gap rotating laser-MIG hybrid welding of 5A06 aluminum alloy

Xiaoyi Yang et al.

Summary: The study demonstrates that an appropriate rotating laser can effectively reduce porosity, improve joint quality, and enhance sidewall fusion in NG-RLMHW of 5A06 aluminum alloy. The stirring effect of the rotating laser results in smaller grain size and more uniform temperature gradient in the molten pool, promoting the morphology transformation in the weld metal.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Modeling of weld formation in variable groove narrow gap welding by rotating GMAW

Wenhang Li et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Article Automation & Control Systems

Formation and suppression mechanism of lack of fusion in narrow gap laser-arc hybrid welding

Yunfei Meng et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

添加到收藏夹

Article Engineering, Industrial

Numerical analysis of heat transfer and fluid flow in swing arc narrow gap GMA welding

Guoxiang Xu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

添加到收藏夹

Article Engineering, Industrial

Characteristics and formation mechanism of sidewall pores in NG-GMAW of 5083 Al-alloy

Chenxiao Zhu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Single pass hybrid laser-arc welding of 25 mm thick square groove butt joints

M. Wahba et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Automation & Control Systems

Groove sidewall penetration modeling for rotating arc narrow gap MAG welding

Wenhang Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

添加到收藏夹

Article Automation & Control Systems

Research on narrow-gap GMAW with swing arc system in horizontal position

H. C. Cui et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)

添加到收藏夹

Article Engineering, Industrial

On the effects of gravity and sulfur content on the weld shape in horizontal narrow gap GTAW of stainless steels

A. Traidia et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Study on the application for electromagnetic controlled molten pool welding process in overhead and flat position welding

M. Shoichi et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2013)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

A Swing Arc System for Narrow Gap GMA Welding

Jiayou Wang et al.

ISIJ INTERNATIONAL (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Application of rotating arc system to horizontal narrow gap welding

C. L. Yang et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.