☆ 4.7 Article

High velocity flame spraying of highly-filled ceramic-Polymer filaments (F-HVOF)

SURFACE & COATINGS TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Review Materials Science, Coatings & Films

Suspension and Solution Precursor Plasma and HVOF Spray: A Review

Garima Mittal et al.

Summary: Thermal spray is a cost- and time-efficient process used in industrial and engineering sectors for mass production of desired coating structures. Liquid feedstocks in the form of suspensions or precursor solutions have the potential to overcome limitations of conventional powder feedstocks and offer better control over coating microstructure and material composition. However, there are complexities associated with liquid feedstocks that require understanding of the effects of different parameters on coating quality and performance.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

High velocity suspension flame spraying of AlN/Al2O3 composite coatings

M. Blum et al.

Summary: Investigation was conducted on the direct spraying of AlN using a supersonic suspension flame spray (HVSFS) process to enhance the thermal conductivity, and the performance of the sprayed coatings, including morphology and phase composition, was analyzed. The results showed that the coatings with axially injected pure AlN suspension had the highest AlN content, and the thermal conductivity values were positively correlated with the AlN content in the coatings.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Polymer Science

Mechanical Properties of 3D-Printed PEEK/HA Composite Filaments

Jianfeng Kang et al.

Summary: This study investigated the three-dimensional printing of polyether ether ketone (PEEK) composite filaments containing varying proportions of hydroxyapatite (HA). Experimental and finite element analysis results showed that the addition of HA increased the elastic modulus of the composite, while decreasing the tensile strength and fracture elongation. The dispersion of particles had a significant impact on the anisotropic coefficient of the modulus.

POLYMERS (2022)

添加到收藏夹

Article Pharmacology & Pharmacy

Brittle polymers in Fused Deposition Modeling: An improved feeding approach to enable the printing of highly drug loaded filament

Nadine Gottschalk et al.

Summary: This study explores a method of printing brittle filaments using a different feeding mechanism, avoiding the use of additional excipients. By investigating the influence of drug load with Ketoconazole on mechanical properties, and analyzing the crystallinity and compatibility of components in filaments, uniform tablets were successfully manufactured.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2021)

添加到收藏夹

Article Chemistry, Physical

Additive Manufacturing of β-Tricalcium Phosphate Components via Fused Deposition of Ceramics (FDC)

Steffen Esslinger et al.

Summary: This study successfully manufactured bioceramic bone graft scaffolds with micro and macro pores using the Fused Deposition of Ceramics (FDC) technique, which have good compressive strength and open porosity, contributing to bone healing.

MATERIALS (2021)

添加到收藏夹

Article Polymer Science

Kinetics of the Thermal Degradation of Poly(lactic acid) and Polyamide Bioblends

Felix Carrasco et al.

Summary: The properties and thermal stability of PLA were improved by adding a reactive agent and varying weight percentage of PA. The GAE equation was used to evaluate the thermal degradation parameters of PLA, confirming that random scission mechanism is the most probable for PLA degradation.

POLYMERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks

Monika Michalak et al.

Summary: Thermally sprayed ceramic coatings are used to protect surfaces exposed to wear, high temperatures, and corrosion, with coatings using suspension feedstocks demonstrating better wear resistance. S-HVOF and axial suspension plasma spraying (A-SPS) allow for the deposition of the most dense, homogeneous coatings.

COATINGS (2021)

添加到收藏夹

Article Chemistry, Physical

High Velocity Suspension Flame Spraying (HVSFS) of Metal Suspensions

Matthias Blum et al.

MATERIALS (2020)

添加到收藏夹

Article Polymer Science

A Study of the Thermal Degradation and Combustion Characteristics of Some Materials Commonly Used in the Construction Sector

Javier Arturo Piedrahita Solorzano et al.

POLYMERS (2019)

添加到收藏夹

Article Polymer Science

Thermal and flammable stability of radiated LDPE and composites

Maziyar Sabet et al.

INTERNATIONAL JOURNAL OF PLASTICS TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and phase stability of suspension high velocity oxy-fuel sprayed yttria stabilised zirconia coatings from aqueous and ethanol based suspensions

M. Bai et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

添加到收藏夹

Article Pharmacology & Pharmacy

Coupling 3D printing with hot-melt extrusion to produce controlled-release tablets

Jiaxiang Zhang et al.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2017)

添加到收藏夹

Article Polymer Science

Degradation of polymer blends: A brief review

F. P. La Mantia et al.

POLYMER DEGRADATION AND STABILITY (2017)

添加到收藏夹

Article Pharmacology & Pharmacy

An investigation into the use of polymer blends to improve the printability of and regulate drug release from pharmaceutical solid dispersions prepared via fused deposition modeling (FDM) 3D printing

Muqdad Alhijjaj et al.

EUROPEAN JOURNAL OF PHARMACEUTICS AND BIOPHARMACEUTICS (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

The 2016 Thermal Spray Roadmap

Armelle Vardelle et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2016)

添加到收藏夹

Review Green & Sustainable Science & Technology

Recent research developments in polymer heat exchangers - A review

Xiangjie Chen et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

What Do We Know, What are the Current Limitations of Suspension Plasma Spraying?

P. Fauchais et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

What Do We Know, What are the Current Limitations of Suspension HVOF Spraying?

A. Killinger et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Performance Testing of Suspension Plasma Sprayed Thermal Barrier Coatings Produced with Varied Suspension Parameters

Nicholas Curry et al.

COATINGS (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

Influence of water and ethanol on transport properties of the jets used in suspension plasma spraying

Bernard Pateyron et al.

SURFACE & COATINGS TECHNOLOGY (2013)

添加到收藏夹

Article Materials Science, Coatings & Films

Latest Developments in Suspension and Liquid Precursor Thermal Spraying

Pierre Fauchais et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2010)

添加到收藏夹

Article Materials Science, Coatings & Films

Corrosion Resistance of APS- and HVOF-Sprayed Coatings in the Al2O3-TiO2 System

F. -L. Toma et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2010)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructures and Functional Properties of Suspension-Sprayed Al2O3 and TiO2 Coatings: An Overview

Filofteia-Laura Toma et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2010)

添加到收藏夹

Article Polymer Science

Polylactide compositions.: Part 1:: Effect of filler content and size on mechanical properties of PLA/calcium sulfate composites

Marius Murariu et al.

POLYMER (2007)

添加到收藏夹

Article Thermodynamics

3D predictions of thermally sprayed polymer splats: Modeling particle acceleration, heating and deformation on impact with a flat substrate

Milan Ivosevic et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2006)

添加到收藏夹

Article Engineering, Chemical

Phenomena involved in suspension plasma spraying part 1: Suspension injection and behavior

J. Fazilleau et al.

PLASMA CHEMISTRY AND PLASMA PROCESSING (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.