相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Translation and rotation of particles in different flow pattern areas of a silo
Ran Li et al.
PARTICUOLOGY (2023)
Effect of various inserts on flow behavior of Fe2O3 beads in a three-dimensional silo subjected to cyclic discharge- Part II: Exploration of internal dynamic properties
C. C. Liao et al.
POWDER TECHNOLOGY (2022)
Effect of various inserts on flow behavior of Fe2O3 beads in a three-dimensional silo subjected to cyclic discharge- Part I: Exploration of transport properties
Y. C. Chung et al.
POWDER TECHNOLOGY (2022)
DEM study of particle segregation in a rotating drum with internal diameter variations
A. N. Huang et al.
POWDER TECHNOLOGY (2021)
Modelling of full-scale silo experiments with flow correcting inserts using material point method (MPM) based on hypoplasticity
J. Krzyzanowski et al.
POWDER TECHNOLOGY (2021)
DEM simulation of the pressure distribution and flow pattern in a model grain silo with an annular segment attached to the wall
Rafal Kobylka et al.
BIOSYSTEMS ENGINEERING (2020)
Critical time step for DEM simulations of dynamic systems using a Hertzian contact model
Shane J. Burns et al.
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2019)
Loads on grain silo insert discs, cones, and cylinders: Experiment and DEM analysis
R. Kobylka et al.
POWDER TECHNOLOGY (2019)
Numerical modeling of the pattern and wear rate on a structural steel plate using DEM
Franco Perazzo et al.
MINERALS ENGINEERING (2019)
Numerical analysis of flow pattern transition in a conical silo with ellipsoid particles
Yanlong Han et al.
ADVANCED POWDER TECHNOLOGY (2019)
A coupled 3D isogeometric and discrete element approach for modeling interactions between structures and granular matters
Wei Gao et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2019)
DEM analysis of the flow and friction of spherical particles in steel silos with corrugated walls
Eutiquio Gallego et al.
POWDER TECHNOLOGY (2019)
Experimental and numerical study of potassium chloride flow using smoothed particle hydrodynamics
Simon Larsson et al.
MINERALS ENGINEERING (2018)
Numerical prediction of wear in SAG mills based on DEM simulations
Lei Xu et al.
POWDER TECHNOLOGY (2018)
DEM study in the critical height of flow mechanism transition in a conical silo
Yaxiong Zhang et al.
POWDER TECHNOLOGY (2018)
Towards a one parameter equation for a silo discharging model with inclined outlets
Marcela C. Villagran Olivares et al.
POWDER TECHNOLOGY (2018)
Experimental and DEM studies on the particle mixing performance in rotating drums: Effect of area ratio
Xiangwu Xiao et al.
POWDER TECHNOLOGY (2017)
Flow pattern and normal pressure distribution in flat bottom silo discharged using wall outlet
Peijun Wang et al.
POWDER TECHNOLOGY (2016)
Influence of coarse-graining parameters on the analysis of DEM simulations of silo flow
Thomas Weinhart et al.
POWDER TECHNOLOGY (2016)
Model tests of silo discharge in a geotechnical centrifuge
J. C. Mathews et al.
POWDER TECHNOLOGY (2016)
Employing DEM to study the impact of different parameters on the screening efficiency and mesh wear
Akbar Jafari et al.
POWDER TECHNOLOGY (2016)
Experiments on eccentric granular discharge from a quasi-two-dimensional silo
Ritwik Maiti et al.
POWDER TECHNOLOGY (2016)
Prediction of flow patterns during silo discharges using a finite element approach and its preliminary experimental verification
S. Ding et al.
PARTICUOLOGY (2015)
Finite element modelling of wall pressures in a cylindrical silo with conical hopper using an Arbitrary Lagrangian-Eulerian formulation
Yin Wang et al.
POWDER TECHNOLOGY (2014)
Experimental study of the pressures exerted by wheat stored in slender cylindrical silos, varying the flow rate of material during discharge. Comparison with Eurocode 1 part 4
A. Couto et al.
POWDER TECHNOLOGY (2013)
Numerical effects derived from en masse filling of agricultural silos in DEM simulations
C. Gonzalez-Montellano et al.
COMPUTERS AND ELECTRONICS IN AGRICULTURE (2012)
Effect of rolling friction on wall pressure, discharge velocity and outflow of granular material from a flat-bottomed bin
R. Balevicius et al.
PARTICUOLOGY (2012)
Confined granular flow in silos with inserts - Full-scale experiments
M. Wojcik et al.
POWDER TECHNOLOGY (2012)
Discrete element method simulation of properties of a 3D conical hopper with mono-sized spheres
Yaowei Yu et al.
ADVANCED POWDER TECHNOLOGY (2011)
Discrete element modelling of grain flow in a planar silo: influence of simulation parameters
C. Gonzalez-Montellano et al.
GRANULAR MATTER (2011)
Pressure measurements in steel silos with eccentric hoppers
A. Ramirez et al.
POWDER TECHNOLOGY (2010)
Multi-scale study of particle flow in silos
Jintao Wu et al.
ADVANCED POWDER TECHNOLOGY (2009)
Predicting the flow mode from hoppers using the discrete element method
William R. Ketterhagen et al.
POWDER TECHNOLOGY (2009)
The influence of a cone-in-cone insert on flow pattern and wall pressure in a full-scale silo
J. Hartl et al.
CHEMICAL ENGINEERING RESEARCH & DESIGN (2008)
Scratching of polymers - Modeling abrasive ewar
Sujeet K. Sinha et al.
WEAR (2007)
Application of particle image velocimetry (PIV) for deformation measurement during granular silo flow
Cezary Slominski et al.
POWDER TECHNOLOGY (2007)
Grain-scale processes governing shear band initiation and evolution in sands
AL Rechenmacher
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2006)
Simulation of axisymmetric discharging in metallic silos.: Analysis of the induced pressure distribution and comparison with different standards
MA Martínez et al.
ENGINEERING STRUCTURES (2002)
The simulation and experimental study of granular materials discharged from a silo with the placement of inserts
SC Yang et al.
POWDER TECHNOLOGY (2001)
Some outstanding questions in handling of cohesionless particles
S Sundaresan
POWDER TECHNOLOGY (2001)