☆ 4.6 Article

Tensile and High-Cycle Fatigue Properties of Die-Cast SEN6 Magnesium Alloy

METALS AND MATERIALS INTERNATIONAL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Aging Hardening and Precipitation Characteristics of Extruded Mg-9Al-0.8Zn-0.2Mn-0.3Ca-0.2Y Alloy

Hyun Ji Kim et al.

Summary: In this study, a new alloy, AZXW9100, with high corrosion and ignition resistance characteristics is developed. The aging hardening and Mg17Al12 precipitation behavior of this alloy are investigated and compared with a commercial AZ91 counterpart. The results show that adding small amounts of Ca and Y to AZ91 alloy significantly alters the precipitation behavior during aging.

METALS AND MATERIALS INTERNATIONAL (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy

Guodong Niu et al.

Summary: In this study, a chill layer with high supersaturation was observed on the surface of Al-7Si-0.5Mg die casting tensile samples. The chill layer has fine alpha-Al grains and its formation mechanism is attributed to the pre-solidified dendrites formed in the shot sleeve and the nonuniform velocity distribution of the melt. The chill layer with solute enrichment promotes the precipitation of tiny Mg2Si phase from the supersaturated alpha-Al grains, which improves the strength and ductility simultaneously.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tensile and High-Cycle Fatigue Properties of Extruded AZ91-0.3Ca-0.2Y Alloy with Excellent Corrosion and Ignition Resistances

Jae Won Cha et al.

Summary: The addition of small amounts of Ca and Y to commercial Mg-Al-Zn alloys can lead to finer grains and higher microstructural homogeneity through promoting dynamic recrystallization. Despite similar tensile strengths, the extruded SEN9 alloy has higher tensile elongation compared to the extruded AZ91 alloy. In fatigue studies, the extruded SEN9 alloy exhibits a higher risk of fatigue crack initiation at low stress amplitudes.

METALS AND MATERIALS INTERNATIONAL (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

On the deformation behavior of heterogeneous microstructure and its effect on the mechanical properties of die cast AZ91D magnesium alloy

Mengwu Wu et al.

Summary: This study investigates the effect of flow distributor improvement on the microstructure and mechanical properties of AZ91D magnesium alloy samples obtained through high pressure die casting. The results reveal that samples with a more homogeneous microstructure demonstrate higher mechanical properties.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-Cycle Fatigue Behavior and Fatigue Strength Prediction of Differently Heat-Treated 35CrMo Steels

Mengqi Yang et al.

Summary: Different heat treatment procedures were applied to 35CrMo steel in order to obtain the optimum fatigue performance. The microstructure, tensile properties, fatigue properties, and fatigue cracking mechanisms were compared and analyzed. The results showed that both the fatigue strength and yield strength of the steel reached the maximum values at a tempering temperature of 200 degrees C.

METALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of SiC Nanofiber Addition on Microstructure, Mechanical Properties and Creep Behaviour of High Pressure Die Cast AZ91-1Sr Alloy

Gueven Yarkadas et al.

Summary: The effects of nanofiber SiC addition on AZ91-1Sr alloy were investigated, resulting in improved mechanical properties with the best yield strength and hardness increment in the nanocomposite. Increased SiC content also led to enhanced creep resistance in the materials, with the dominant creep mechanism identified as dislocation climb controlled.

METALS AND MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Lanthanum Addition on Grain Refinement and Mechanical Properties of Mg-9Li-3Al Alloy

P. Dinesh et al.

Summary: The study found that the addition of lanthanum can induce microstructural changes and mechanical characteristics in Mg-9Li-3Al alloys. The addition of an appropriate amount of lanthanum is beneficial to the alloy system, resulting in grain refinement and increased tensile strength, while excessive addition may lead to grain coarsening and reduced mechanical strength.

METALS AND MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Microstructural Features on the High-Cycle Fatigue Behavior of CoCrFeMnNi High-Entropy Alloys Deformed at Room and Cryogenic Temperatures

Gyung Tae Lee et al.

Summary: This study investigated the influence of deformation twins and dislocation cell structures on the fatigue properties of the CoCrFeMnNi high-entropy alloy through rotational bending fatigue tests. It was found that prestraining at room temperature resulted in higher fatigue resistance and fatigue limit compared to prestraining at cryogenic temperature, with different aspects of micro-void formation affecting crack initiation and fatigue properties.

METALS AND MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Industrial

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

X. Y. Jiao et al.

Summary: Study on ESCs and porosities in high-pressure die-cast AlSi10MnMg alloy revealed the impact of shot speeds on ESC formation and fracture behavior, with slower speeds leading to increased ESCs and porosities. The presence of ESCs and porosities significantly influenced the fracture morphology and crack propagation during in-situ tensile tests, indicating the importance of controlling shot speeds in die casting processes.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative study of tensile and high-cycle fatigue properties of extruded AZ91 and AZ91-0.3Ca-0.2Y alloys

Ye Jin Kim et al.

Summary: The SEN9 alloy exhibits finer grains and more abundant particles, resulting in slightly higher tensile strength compared to the AZ91 alloy. However, the difference in strength between the two alloys is relatively small as the effects of solid-solution hardening and precipitation hardening in the AZ91 alloy offset the effects of grain-boundary hardening and dispersion hardening in the SEN9 alloy to some extent.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Research and Development in Magnesium Alloys for Industrial and Biomedical Applications: A Review

Vaira Vignesh Ramalingam et al.

METALS AND MATERIALS INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Metallurgical Assessment of Novel Mg-Sn-La Alloys Produced by High-Pressure Die Casting

Azim Gokce

METALS AND MATERIALS INTERNATIONAL (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of vacuum on porosity and mechanical properties of high-pressure die-cast pure copper

Hong-mei Yang et al.

CHINA FOUNDRY (2019)

添加到收藏夹

Article Engineering, Mechanical

Engineering prediction of fatigue strength for AM50 magnesium alloys

Liviu Marsavina et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of non-flammable Mg-8Al-0.3Zn-0.1Mn-0.3Ca-0.2Y alloy subjected to low-temperature, low-speed extrusion

Yohan Go et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructural evolution and improvement in mechanical properties of extruded AZ31 alloy by combined addition of Ca and Y

Sang-Hoon Kim et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improving Corrosion and Corrosion-Fatigue Resistance of AZ31B Cast Mg Alloy Using Combined Cold Spray and Top Coatings

Sugrib Kumar Shaha et al.

COATINGS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Role of alloyed Y in improving the corrosion resistance of extruded Mg-Al-Ca-based alloy

Soo-Min Baek et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Correlation between Porosity and Fracture Mechanism in High Pressure Die Casting of AM60B Alloy

X. Li et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

2D and 3D characterization of pore defects in die cast AM60

Zhuofei Yang et al.

MATERIALS CHARACTERIZATION (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

On the tensile failure induced by defect band in high pressure die casting of AM60B magnesium alloy

X. Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Failure behavior of high pressure die casting AZ91D magnesium alloy

X. Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

In-situ SEM study of fatigue crack initiation and propagation behavior in 2524 aluminum alloy

Liang Yan et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-Pressure Die-Casting: Contradictions and Challenges

Franco Bonollo et al.

JOM (2015)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Micro-porosities on Fatigue Behavior in Aluminum Die Castings by 3D X-ray Tomography Inspection

Qian Wan et al.

ISIJ INTERNATIONAL (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Research on the microstructure, fatigue and corrosion behavior of permanent mold and die cast aluminum alloy

Zuqi Hu et al.

MATERIALS & DESIGN (2014)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanical properties and fatigue behavior of vacuum-assist die cast AlMgSiMn alloy

Li Wan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Magnesium casting technology for structural applications

Alan A. Luo

JOURNAL OF MAGNESIUM AND ALLOYS (2013)

添加到收藏夹

Article Engineering, Mechanical

Scatter analysis of fatigue life and pore size data of die-cast AM60B magnesium alloy

S. Mohd et al.

ENGINEERING FAILURE ANALYSIS (2012)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Fatigue behaviour of A356 aluminium alloy for automotive wheels

J. -Y. Song et al.

INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2012)

添加到收藏夹

Article Engineering, Mechanical

On fatigue lives of diecast and extruded Mg alloys

S. Ishihara et al.

INTERNATIONAL JOURNAL OF FATIGUE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Fe content and microstructural features on the tensile and fatigue properties of the Al-Si10-Cu2 alloy

Lorella Ceschini et al.

MATERIALS & DESIGN (2012)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effects of combined addition of Y and Ca on microstructure and mechanical properties of die casting AZ91 alloy

Feng WANG et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

In situ observation of tensile deformation of high-pressure die-cast specimens of AM50 alloy

Jie Song et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of grain size on the tensile properties of magnesium alloy

Choong Do Lee

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)

添加到收藏夹

Article Chemistry, Applied

High cycle fatigue properties of die-cast magnesium alloy AZ91D with addition of different concentrations of cerium

Yang You et al.

JOURNAL OF RARE EARTHS (2006)

添加到收藏夹

Article Engineering, Mechanical

Effects of Mn content and texture on fatigue properties of as-cast and extruded AZ61 magnesium alloys

Z Bin Sajuri et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2006)

添加到收藏夹

Article Engineering, Mechanical

The effect of porosity on the fatigue life of cast aluminium-silicon alloys

YX Gao et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2004)

添加到收藏夹

Article Engineering, Mechanical

Influence of porosity on the fatigue limit of die cast magnesium and aluminium alloys

H Mayer et al.

INTERNATIONAL JOURNAL OF FATIGUE (2003)

添加到收藏夹

Article Engineering, Mechanical

High cycle fatigue mechanics in a cast AM60B magnesium alloy

MF Horstemeyer et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.