☆ 4.7 Article

Multi-wire arc additive manufacturing of TC4/Nb bionic layered heterogeneous alloy: Microstructure evolution and mechanical properties

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Deformation behavior and fracture mechanism of laminated Ti/Ti-50 Nb alloy with diffusion layer

Yanfei Yin et al.

Summary: The laminated Ti/Ti-50 Nb alloy was successfully fabricated and its microstructure, texture evolution, and fracture behavior were investigated. The results showed that the diffusion layer enhanced the strength of the alloy, while the grain rotation in the TiNb layers suppressed the strain concentration.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Review Materials Science, Multidisciplinary

Microstructure and hot deformation behavior of the Cu-Sn-Ni-Zn-Ti (-Y) alloy

Deye Xu et al.

Summary: The effects of Y addition on microstructure evolution in Cu-Sn-Ni-Zn-Ti alloys during hot deformation were investigated. Hot deformation experiments were conducted using a Gleeble-1500 simulator, deforming Cu-Sn-Ni-Zn-Ti and Cu-Sn-Ni-Zn-Ti-Y alloys at temperatures ranging from 550 to 950 degrees C and strain rates of 0.001-10 s-1. Constitutive equations were constructed and the hot deformation activation energy of the two alloys was calculated. It was found that the addition of 0.1 wt% rare earth Y element can promote dynamic recrystallization based on analysis of true stress-strain curves and electron backscattered diffraction images. Pole figures showed a texture change from {011}(112) Brass texture and {001}(100) Cube texture to {111}(211) R texture after Y addition. The microstructure and precipitates of the Cu-Sn-Ni-Zn-Ti alloy were analyzed, revealing the presence of Cu4Ti precipitates. Continuous dynamic recrystallization and discontinuous dynamic recrystallization were identified as the main recrystallization mechanisms in the Cu-Sn-Ni-Zn-Ti alloy.

MATERIALS CHARACTERIZATION (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of TC4/NiTi bionic gradient heterogeneous alloy prepared by multi-wire arc additive manufacturing

P. F. Jiang et al.

Summary: TC4/NiTi multi-materials structure components were successfully fabricated via multi-wire arc additive manufacturing (MWAAM). The interface characteristics and mechanical properties of TC4/NiTi multi-materials structure component under bionic gradient interlayer build strategy were investigated. The results showed that MWAAM TC4/NiTi gradient heterogeneous alloy exhibited excellent compression behavior, with an ultimate compression strength of 1533.33 +/- 26 MPa.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Influence of local thermal cycle on the lattice and microstructure evolution of twin-wire directed energy deposition-arc fabricated equiatomic NiTi alloy

Andrew Bulla et al.

Summary: The authors investigated the effect of repeated heating cycles on the phase and crystal structure of a few layers at a time. Equiatomic NiTi alloy was additively manufactured using twin-wire directed energy deposition-arc (TW-DED-arc). Microstructure characterization revealed the incorporation of silicon preventing the formation of NiTi2 and the existence of two types of B2 austenite in the matrix. Mechanical testing showed a maximum ultimate tensile stress of 782.5 MPa with a fracture surface indicative of quasi-cleavage failure.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Engineering, Manufacturing

Multi-material additive manufacturing of a bio-inspired layered ceramic/metal structure: Formation mechanisms and mechanical properties

Rui Wang et al.

Summary: This research reveals the mechanisms of material densification, element diffusion, interfacial reaction, crystal growth, and performance enhancement in multi-material laser powder bed fusion (LPBF) through experiments and simulations. Fully dense multi-material parts with strong metallurgical bonding and gradually changing microhardness at the interface were achieved by optimizing the printing parameters. The laser printed TiB2/Ti6Al4V multi-material parts exhibited excellent flexural performance with improved strength and ductility. This study is significant for the manufacturing and strengthening of ceramic/metal multi-material using laser additive manufacturing technology.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

Chaoping You et al.

Summary: This paper reports a dual heterogeneous laminated (DHLed) Cu/Cu-Cr-Zr composite structure in copper alloys produced by accumulative roll bonding (ARB) and annealing process that can achieve an excellent combination of mechanical properties and electrical conductivity.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and fatigue behavior of 24CrNiMo low alloy steel prepared by selective laser melting

X. Cui et al.

Summary: The microstructure and fatigue performance of 24CrNiMo low alloy steel by selective laser melting (SLM) were investigated. The SLM sample showed a relatively high fatigue strength due to the excellent combination of strength and plasticity. Manufacturing defects and the matrix could act as crack initiation sites, with the former being divided into surface and interior defects. The location of original cracks had a greater impact on fatigue lifetime than the type of original cracks.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Controlling the microstructure and fracture toughness of the Ti-5Al-5Mo-5V-1Cr-1Fe alloy by multiple heat treatments

Zedong Liu et al.

Summary: This study shows the significant influence of microstructure and fracture toughness of the Ti-55511 alloy during STA and STAA heat treatment processes. The proper solution treatment and aging temperature can enhance the toughness of the alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of Ti basic bionic gradient heterogeneous alloy prepared by multi-wire arc additive manufacturing

P. F. Jiang et al.

Summary: Inspired by biological gradient structure, Ti basic gradient heterogeneous alloy component from TC11 alloy to TC4 alloy was successfully fabricated using multi-wire arc additive manufacturing (MWAAM). The chemical mixing, phase and microstructure evolution, microhardness distribution, and tensile property of the Ti basic gradient heterogeneous alloy were investigated. The results showed that the alloy elements formed a long-distance gradient concentration distribution during the transition between two different titanium alloys. The diffraction peak intensity of the Ti basic gradient heterogeneous alloy in the gradient region remained unchanged. The microstructure of the alloy mainly consisted of lamellar alpha(P), acicular alpha(S), equiaxed alpha(S), and beta matrix. The morphology of the alpha(S) phase varied due to the wetting state of the second solid phase and grain boundary. Moreover, the microstructure of the alpha phase was significantly influenced by the gradient distribution of alloy composition. The gradient heterogeneous alloy component exhibited high bonding strength, with an average ultimate tensile strength close to TC4 alloy and approximately 85% of TC11 alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Engineering, Industrial

High strength Ti alloy fabricated by directed energy deposition with in-situ Cu alloying

Jian Han et al.

Summary: A high strength Ti-6Al-4V-8.5Cu component was successfully fabricated using directed energy deposition technology, and its microstructure and performance were investigated. The addition of Cu resulted in refined grains and the presence of Cu in solid solution and Ti2Cu particles. As a result, the hardness and tensile strength of the component were significantly improved.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Twin-wire directed energy deposition-arc of Ti-48Al-2Cr-2Nb alloy: Feasibility, microstructure, and tensile property investigation

Wenlu Zhou et al.

Summary: Due to its low density and good high temperature performance, titanium aluminide has attracted attention in the aerospace and automotive industries. In recent years, additive manufacturing of titanium aluminide has become popular. This study successfully fabricated commercial graded TiAl-4822 alloy using an innovative TW-DED-arc process, resulting in good mechanical properties and uniform chemical composition.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Heterostructured alloys with enhanced strength-ductility synergy through laser-cladding

Rae Eon Kim et al.

Summary: In this study, a simple process of laser-cladding was proposed to develop heterostructured alloys, which showed enhanced strength and ductility compared to traditional alloys. The hetero-deformation-induced strengthening resulted in an improved strength-ductility synergy.

SCRIPTA MATERIALIA (2022)

添加到收藏夹

Article Chemistry, Physical

Multi-wire arc additive manufacturing of Ti basic heterogeneous alloy: Effect of deposition current on the microstructure, mechanical property and corrosion-resistance

P. F. Jiang et al.

Summary: This study investigates the effect of deposition current on the microstructure and properties of titanium alloy components prepared by multi-wire arc additive manufacturing (MWAAM) technology. The results show that increasing the deposition current influences the width and aspect ratio of the alpha phase, leading to decreased mechanical properties. The MWAAM-deposited titanium alloys exhibit excellent corrosion properties.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and properties of a Ni-Ti-Cr-Mo-Nb alloy fabricated in situ by dual-wire arc additive manufacturing

Yinbao Tian et al.

Summary: In this study, a Ni-Ti-Cr-Mo-Nb wall component was fabricated for potential use in low temperature environments. The component exhibited outstanding superelasticity and hardness, with an austenite finish temperature of -62 degrees Celsius.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Influence of annealing on the microstructure and Charpy impact toughness of wire arc additive manufactured Ti5111 alloy

Feipeng An et al.

Summary: The microstructure, tensile properties, and impact toughness of wire arc additive manufactured (WAAMed) titanium alloy were investigated. The results showed that by using a newly developed deformation twinning induced plasticity alloy and annealing treatment, titanium alloy with excellent toughness can be obtained.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hierarchical transition structure induced by gradient composition distribution in layered Ti-TiNb alloy

Yanfei Yin et al.

Summary: In this study, a hierarchical transition structure with multiphase architectures, caused by elemental gradients, is obtained in the investigated layered Ti-TiNb alloy. The component types of the alloy are enriched from 2 types to 7 types. Special attention is given to the architectures consisting of alpha-phase in two shapes and nano-sized omega-phase, introduced by heterogeneously precipitating behavior. This study can serve as a template for designing and developing a new class of layered metal materials with multi-component features.

SCRIPTA MATERIALIA (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Dynamic response of Ti-6.5Al-1Mo-1V-2Zr-0.1B alloy fabricated by wire arc additive manufacturing

Linan Xue et al.

Summary: In this study, a thin-walled sample made by WAAM method using Ti-6.5Al-1Mo-1V-2Zr-0.1B wires showed low anisotropy in mechanical response at a strain rate of 3000 s(-1) along both OY and OZ directions. The presence of B element in the near-alpha titanium alloy and the equiaxed prior-beta grain structure in the as-deposited sample played a role in reducing anisotropy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Optics

Additive manufacturing of novel ferritic stainless steel by selective laser melting: Role of laser scanning speed on the formability, microstructure and properties

P. F. Jiang et al.

Summary: Novel ferritic stainless steel was fabricated by SLM technology, with densification level significantly improved by increasing laser energy density. Microstructure was mainly ?-Fe with some Cr23C6, and LAGBs and ?-Fe proportions increased with higher laser scanning speed. SLM specimens exhibited excellent properties, especially in corrosion resistance.

OPTICS AND LASER TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tribological and cavitation erosion behaviors of nickel-based and iron-based coatings deposited on AISI 304 stainless steel by cold metal transfer

Xu Tang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of stress-relief heat treatment on the microstructure and fatigue property of a laser additive manufactured 12CrNi2 low alloy steel

X. Cui et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced interface strength in steel-nickel bimetallic component fabricated using wire arc additive manufacturing with interweaving deposition strategy

Bintao Wu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Deformation behavior of a novel sandwich-like TiNb/NiTi composite with good biocompatibility and superelasticity

Shun Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution, wear behavior, and corrosion performance of alloy steel gradient material fabricated by direct laser deposition

P. F. Jiang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Interfacial characteristics and mechanical properties of TiAl/Ti6Al4V laminate composite (LMC) fabricated by vacuum hot pressing

Haifeng Zhu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Influence of phosphorus on hot deformation microstructure of a Ni-Fe-Cr based alloy

Yunsheng Wu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Chemistry, Physical

Effects of niobium addition on the microstructure and mechanical properties of laser-welded joints of NiTiNb and Ti6Al4V alloys

Xingwen Zhou et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced compressive strength and tailored microstructure of selective laser melted Ti-46.5Al-2.5Cr-2Nb-0.5Y alloy with different boron addition

Wei Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Review Chemistry, Multidisciplinary

Additive Manufacturing as a Method to Design and Optimize Bioinspired Structures

Audrey Velasco-Hogan et al.

ADVANCED MATERIALS (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Bioinspired 3D structures with programmable morphologies and motions

Amirali Nojoomi et al.

NATURE COMMUNICATIONS (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Giga-voxel computational morphogenesis for structural design

Niels Aage et al.

NATURE (2017)

添加到收藏夹

Article Optics

Effect of heat treatment on residual stress and wear behaviors of the TiNi/Ti2Ni based laser cladding composite coatings

Yang-Feng Tao et al.

OPTICS AND LASER TECHNOLOGY (2017)

添加到收藏夹

Article Mechanics

Graded layered titanium composite structures with TiB2 inclusions fabricated by selective laser melting

Igor Shishkovsky et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Characterization of heat affected zone liquation cracking in laser additive manufacturing of Inconel 718

Yuan Chen et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Multidisciplinary Sciences

Protection mechanisms of the iron-plated armor of a deep-sea hydrothermal vent gastropod

Haimin Yao et al.

PROCEEDINGS OF THE NATIONAL ACADEMY OF SCIENCES OF THE UNITED STATES OF AMERICA (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

Interface toughness under combined mode I, II and III loadings

P Liu et al.

SCRIPTA MATERIALIA (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.