☆ 4.7 Article

Local anti-ablation modification of uneven-density C/C composites with the ZrC-SiC composite ceramics

MATERIALS CHARACTERIZATION (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

The evaluation of microstructure of carbon/carbon composites generated by ultra-high temperature treatment towards excellent electromagnetic interference shielding property

Kun Xue et al.

Summary: This study raises the treatment temperature of carbon/carbon (C/C) composites and explores the influence of micromorphology on the mechanical and electromagnetic shielding properties of materials using an innovative image recognition method. The results indicate that increasing the treatment temperature leads to increased porosity and improved graphitization degree of the composites. Moreover, the electromagnetic shielding efficiency (SE) of the composites shows a consistent trend with electrical conductivity, and reflection is identified as the dominant shielding mechanism. Comparative analysis of comprehensive data suggests that C/C composites have the potential to be a new generation of satellites with electromagnetic shielding material.

CARBON (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Understanding on interlaminar nano-reinforcement induced mechanical performance improvement of carbon/carbon composites after silicon infiltration

Caixiang Xiao et al.

COMPOSITES PART B-ENGINEERING (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Irradiation induced interface modification of carbon fiber/carbon composite revealed by in-situ transmission electron microscopy

Shanglei Feng et al.

Summary: This study used a high-voltage electron microscope to monitor the in-situ irradiation effect on the fiber and matrix interfaces of C/C composites induced by electron beam. The results showed that their finer microstructures exhibited two different evolutions. Under electron irradiation, the strong bonding interface showed no obvious boundary between the fiber and matrix, while the weak bonding interface had a transition layer composed of amorphous materials. The electron irradiation also caused the banded microcrystals at the longitudinal interface of the fibers to become amorphous, expanded the substrate surface, and gradually closed microcracks. Nano indenter experiments confirmed the significantly enhanced mechanical properties of the fiber and matrix induced by electron irradiation.

COMPOSITES PART B-ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

SiC/HfB2-based ceramic/SiC multilayer coating to protect C/C composites against oxidation at medium and high temperatures for long-life service

Xiaofei Zhu et al.

Summary: A SiC/HfB2-based ceramic/SiC multilayer coating was developed using a combination of pack cementation, slurry brushing-pressureless reaction sintering, and chemical vapor deposition. The coating exhibited excellent oxidation resistance and effectively protected C/C composites.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multiple cyclic ablation behaviors of multilayer ZrC-TaC coating with ZrC-SiC interface layer

Dou Hu et al.

Summary: This study investigates the improvement of multiple cyclic ablation performance of ablation resistant coating through the design and fabrication of (ZrC-TaC)/(ZrC-SiC) multilayer coating. The results showed that the linear variation rate of the multilayer coating decreased by 75% compared to the monolayer ZrC-TaC coating, which was attributed to the control of low Ta/Zr ratio to increase the temperature resistance of Zr-Ta-O oxide film and the interfacial crack deflection induced by the ZrC-SiC interface layer.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ultra-high temperature ablation behaviour of 2.5D SiC/SiC under an oxy-acetylene torch

Jinkang Du et al.

Summary: The ablation characteristics of 2.5D SiC/SiC composites under ultra-high temperatures were studied using an oxy-acetylene torch flame. The results showed that the ablation region could be divided into three regions based on the distribution characteristics of SiO2. The ablation rate decreased linearly with time and the fracture of the fiber underwent three processes: Necking, fracture, and stable retreat.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Ceramics

Exploring Hf-Ta-O precipitation upon ablation of Hf-Ta-Si-C coating on C/C composites

Mingde Tong et al.

Summary: A Hf-Ta-Si-C coating was fabricated by chemical vapor co-deposition to improve the ablation resistance of C/C composites. The ablation resistance, smoothness, and integrity of the coating were improved by introducing Ta. Hf and Ta atoms tend to gather together at high temperature. The precipitation reaction of Hf-Ta-O can accelerate the formation of a smooth and intact oxide layer, playing a positive role in protecting C/C composites.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Materials Science, Ceramics

Construction of sandwich-structured C/C-SiC and C/C-SiC-ZrC composites with good mechanical and anti-ablation properties

Rida Zhao et al.

Summary: Sandwich-structured C/C-SiC and C/C-SiC-ZrC composites with or without a SiC interphase were fabricated using a joint process of ECVI and PIP. The composites exhibited low density, high strength, and low ablation rate, with the interphase and matrix constituents playing a significant role in their mechanical and ablation properties.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Review Chemistry, Multidisciplinary

Recent Progress in 1D Nanostructures Reinforced Carbon/Carbon Composites

Xuemin Yin et al.

Summary: Carbon fiber reinforced carbon matrix composites are promising materials for high-temperature thermal structures in aerospace fields. However, sharp or thin-walled composites often experience a decline in mechanical performance due to the cutting of carbon fibers during machining. To overcome this issue, various one-dimensional nanoreinforcements have been introduced to enhance the mechanical and functional properties of C/C composites. This review summarizes the latest research activities and provides future research prospects in this field.

ADVANCED FUNCTIONAL MATERIALS (2022)

添加到收藏夹

Article Materials Science, Ceramics

Hybrid coating of polydimethylsiloxane with nano-ZrO2 on magnesium alloy for superior corrosion resistance

Jialin Yang et al.

Summary: The thermal stability, hydrophobicity, and corrosion resistance of the PDMS-ZrO2 coatings are substantially improved by introducing ZrO2 nanoparticles. Depending on the ZrO2 content, the PDMS-ZrO2 hybrids exhibit superior corrosion resistance.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of temperature gradient on the ablation and flexural behavior of C/C-ZrC composites

Tianyu Liu et al.

Summary: A new ablation condition was designed to investigate the effect of temperature gradient on the ablation and flexural behavior of C/C-ZrC composites. The volume change caused by ZrC -> ZrO2 and the ZrO2 crystalline transformation were beneficial for releasing internal stress, thereby contributing to the higher flexural strength retention of the composites.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Chemistry, Physical

Full-scale multi-physics numerical analysis of an isothermal chemical vapor in filtration process for manufacturing C/C composites

Hye-gyu Kim et al.

Summary: The developed 3D CVI model successfully simulates the isothermal process for fabricating carbon-carbon composites, considering gas flow behavior and chemical reactions. The model accurately predicts the evolution of preform density and porosity, offering detailed simulations not observable experimentally.

CARBON (2021)

添加到收藏夹

Article Materials Science, Ceramics

Improvement of ablation resistance of CVD-HfC/SiC coating on hemisphere shaped C/C composites by introducing diffusion interface

Mingde Tong et al.

Summary: In this study, the bonding strength and ablation resistance of HfC based coating on hemisphere shaped C/C composites were optimized by introducing a HfC-SiC diffusion interface. The results showed a significant increase in bonding strength and a reduction in linear and mass ablation rates after introducing HfC-SiC diffusion. The enhancement of ablation resistance was attributed to the adhesion effect of Hf-Si-O glass phase and the increase of bonding strength in the outer layer.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Zirconium carbide skeleton reinforced pyrocarbon composites with tunable mechanical strength, thermophysical properties and ablation resistance

Ningning Yan et al.

Summary: ZrC-C composites with different weight ratios of ZrC/PyC were prepared, and the results showed that increasing the weight ratio of ZrC/PyC led to higher compressive strengths, as well as the formation of a ZrO2 skeleton that could reduce composite consumption. Finite element simulation demonstrated that thermal stresses increased with the weight ratios of ZrC/PyC.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Ceramics

Ablation properties of C/C-UHTCs and their preparation by reactive infiltration of K2MeF6 (Me = Zr, Ti) molten salt

Yonglong Xu et al.

Summary: The study successfully prepared C/C-UHTCs composites with reduced ablative rate and mass flux by introducing ultra-high temperature ceramic modification in C/C composites.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative insights into C/C-ZrC-SiC composites with different substrate carbon on microstructures, mechanical properties, and ablation behaviors

Zheng Peng et al.

Summary: The study systematically researched the microstructures, mechanical properties, and ablation behaviors of C/C-ZrC-SiC composites fabricated using different carbon substrates, finding that C/PyC-ZrC-SiC composites had higher flexural strength while C/RdC-ZrC-SiC composites exhibited better ablation resistance after exposure to oxyacetylene ablation.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical, oxidation and ablation properties of C/(C-SiC)CVI-(ZrC-SiC)PIP composites

Jinjin Yao et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of ZrC/SiC ratios on mechanical and ablation behavior of C/C-ZrC-SiC composites prepared by carbothermal reaction of hydrothermal co-deposited oxides

Haibo Ouyang et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Ceramics

Effects of preform pore structure on infiltration kinetics and microstructure evolution of RMI-derived Cf/ZrC-ZrB2-SiC composite

Xiaowu Chen et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Chemistry, Physical

A novel continuous carbon nanotube fiber/carbon composite by electrified preform heating chemical vapor infiltration

Lei Feng et al.

CARBON (2020)

添加到收藏夹

Article Materials Science, Ceramics

Continuous alumina fiber-reinforced yttria-stabilized zirconia composites with high density and toughness

Xuewu Li et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and ablation property of gradient ZrC-SiC modified C/C composites prepared by chemical liquid vapor deposition

Qinchuan He et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Porous high entropy (Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2: A novel strategy towards making ultrahigh temperature ceramics thermal insulating

Heng Chen et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructures and mechanical behaviors of CVI-based C/C composites containing h-BN powdered additives

Peng Xiao et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ablation characteristics of mosaic structure ZrC-SiC coatings on low-density, porous C/C composites

Yonglong Xu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Materials characterisation and mechanical properties of Cf-UHTC powder composites

V. Rubio et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Review Materials Science, Ceramics

Advances in oxidation and ablation resistance of high and ultra-high temperature ceramics modified or coated carbon/carbon composites

Xiaochao Jin et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

添加到收藏夹

Article Engineering, Electrical & Electronic

Effects of SiO2 film thickness and operating temperature on thermally-induced failures in through-silicon-via structures

Chang-Fu Han et al.

MICROELECTRONICS RELIABILITY (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Thermal ablation behavior of SiC coating for 3D braided carbon fiber reinforced ZrC-SiC composites in different heat fluxes

Xiao-Hui Yang et al.

VACUUM (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and ablation properties of C/C-Zr-Si-O composites prepared by carbothermal reduction of hydrothermal co-deposited oxides

Haibo Ouyang et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Article Chemistry, Physical

Microstructure, mechanical properties and thermal shock resistance of ZrB2-SiC-Cf composite with inhibited degradation of carbon fibers

Kaixuan Gui et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Review Materials Science, Multidisciplinary

Design, Preparation and Properties of Carbon Fiber Reinforced Ultra-High Temperature Ceramic Composites for Aerospace Applications: A Review

Sufang Tang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Ceramics

Preparation and characterization of ZrB2 and TaC containing Cf/SiC composites via Polymer-Infiltration-Pyrolysis process

Franziska Uhlmann et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Efficacy of a ZrB2-SiC matrix in protecting C fibres from oxidation in novel UHTCMC materials

L. Zoli et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Multidisciplinary Sciences

Sandwich-structured C/C-SiC composites fabricated by electromagnetic-coupling chemical vapor infiltration

Chenglong Hu et al.

SCIENTIFIC REPORTS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Monolithic LaB6 on the Ablation Resistance of ZrC/SiC Coating Prepared by Supersonic Plasma Spraying for C/C Composites

Yujun Jia et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Ceramics

The Fabrication of ZrO2-ZrC Microspheres by Internal Gelation and Carbothermal Reduction Process

Yong Gao et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ablative and Mechanical Properties of C/C-ZrC Composites Prepared by Precursor Infiltration and Pyrolysis Process

Kezhi Li et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Ceramics

An integrated composite with a porous Cf/C-ZrB2-SiC core between two compact outer layers of Cf/C-ZrB2-SiC and Cf/C-SiC

Chenglong Hu et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

添加到收藏夹

Article Materials Science, Ceramics

High temperature oxidation of two- and three-dimensional hafnium carbide and silicon carbide coatings

C. Verdon et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)

添加到收藏夹

Article Chemistry, Physical

Fast densification of thick-walled carbon/carbon composite tubes using electrically coupled chemical vapor infiltration

Wu Xiaojun et al.

CARBON (2013)

添加到收藏夹

Article Chemistry, Physical

Effects of porous C/C density on the densification behavior and ablation property of C/C-ZrC-SiC composites

Ke-zhi Li et al.

CARBON (2013)

添加到收藏夹

Article Materials Science, Ceramics

Zircon-zirconia (ZrSiO4-ZrO2) dense ceramic composites by spark plasma sintering

Nicolas M. Rendtorff et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of carbon nanofibers on the infiltration and thermal conductivity of carbon/carbon composites

Jinsong Li et al.

MATERIALS RESEARCH BULLETIN (2011)

添加到收藏夹

Article Materials Science, Ceramics

Preparation and characterization of C/SiC-ZrB2 composites by precursor infiltration and pyrolysis process

Haifeng Hu et al.

CERAMICS INTERNATIONAL (2010)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.