☆ 4.6 Article

Rational Design of NiO-8YSZ Screen-Printing Slurry for High- Performance Large-Area Solid Oxide Cells

JOURNAL OF PHYSICAL CHEMISTRY C (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Boosting solid oxide electrolyzer performance by fine tuning the microstructure of electrodes - Preliminary study

Jakub Kupecki et al.

Summary: This paper discusses the concept of improving the performance of solid oxide electrolyzers by adjusting the microstructure of the support materials. Instead of major redesigns, this study proposes fine-tuning the microstructure to enhance cell performance. The results show that adjusting the sintering temperature has a greater impact on the support microstructure than increasing the pore-forming agent.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2023)

添加到收藏夹

Article Materials Science, Ceramics

Realizing high-temperature steam electrolysis on tubular solid oxide electrolysis cells sufficing multiple and rapid start-up

Guangdong Li et al.

Summary: A novel tubular SOEC with YSZ and Ni-doped Sr(Ti, Fe)O3 as support and fuel electrode respectively has been proposed and fabricated. The as-fabricated cell showed the ability to electrolyze steam under a hydrogen-free atmosphere and exhibited stable performance during the start-pause cycle test. This work highlights the potential of SOEC devices in future power-to-hydrogen technology.

CERAMICS INTERNATIONAL (2023)

添加到收藏夹

Article Chemistry, Physical

Effects of pore former type on mechanical and electrochemical performance of anode support microtubes in solid oxide fuel cells

Timurkutluk Cigdem et al.

Summary: This study investigates the effects of pore formers added into the extrusion slurry of anode support microtubes on their mechanical and electrochemical performance. Experimental results show that the flexural strength of the microtubes decreases with increasing particle size and pore former content. Electrochemical tests indicate that the cell performance is mainly limited by diffusion polarization. The highest cell performance is achieved with a certain pore former content of graphite (325 mesh) for all temperatures and hydrogen flowrates tested. Optimization studies suggest that further improvement in cell performance can be achieved by increasing the pore former content.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

In-Depth Investigation of Inkjet-Printed Silver Electrodes over Large-Area: Ink Recipe, Flow, and Solidification

Lu Zhou et al.

Summary: This paper presents an in-depth investigation and optimization of template-less inkjet printing for metal mesh-based transparent conducting electrodes. The study focuses on the conductive ink formulation, droplet coalescence and crawling, and solidification processes. The results show that ideal silver lines with high conductivity can be obtained and passive matrix organic light emitting diodes based on silver array electrodes can be successfully fabricated.

ADVANCED MATERIALS INTERFACES (2022)

添加到收藏夹

Article Chemistry, Physical

An adaptive thermo-mechanical peridynamic model for crack analysis in anode-supported solid oxide fuel cell

Yu Xiang et al.

Summary: This study reconstructs the 3D real microstructures of various porous Ni-YSZ anodes using the FIB-SEM technique and proposes a PD model to predict the mechanical damages of different anodes under severe conditions. The equivalent mechanical and thermal properties of the composite anodes are analyzed and correlated to the real microstructures. The research provides a trans-scale model for simulating the generation and propagation of cracks, and shows great potential in supporting the optimization of SOFCs at a trans-scale level.

JOURNAL OF POWER SOURCES (2022)

添加到收藏夹

Article Chemistry, Physical

Effect of total pressure difference on counter transport of gases with different molecular weights through solid oxide fuel cell anode

Kento Sengoku et al.

Summary: The study investigates counter transport of gases with different molecular weights in a hydrogen-steam binary mixture in a solid oxide fuel cell (SOFC). It is found that a total pressure difference is required to enhance the transport of gas with a larger molecular weight. The developed numerical model accurately reproduces experimental results and predicts the limiting current density of an SOFC.

JOURNAL OF POWER SOURCES (2022)

添加到收藏夹

Article Chemistry, Physical

Integrated thermal reforming and electro-oxidation in ammonia-fueled tubular solid oxide fuel cells toward autothermal operation

Nattikarn Jantakananuruk et al.

Summary: Ammonia has been applied as a high-energy-density liquid and carbon-free hydrogen carrier in high-temperature solid oxide fuel cells (SOFCs). This study investigates the spatially resolved thermal and concentration effects of ammonia decomposition and hydrogen oxidation reactions in an intensified tubular SOFC (t-SOFC) fueled directly with ammonia. The experimental results show that efficient heat integration can be achieved in an ammonia-fueled t-SOFC operated at a temperature of 700 degrees C and below, and it exhibits stability and durability during a 150-hour performance test.

JOURNAL OF POWER SOURCES (2022)

添加到收藏夹

Article Chemistry, Physical

Rational Design of Two-Layer Fe-Doped PrBa0.8Ca0.2Co2O6-δ Double Perovskite Oxides for High-Performance Fuel Cell Cathodes

Yuxuan Zhang et al.

Summary: The double-layer PBCC cathode developed in this study shows promising performance in solid oxide fuel cells, with advantages in electrolyte compatibility and conductivity. Compared to traditional PBCC electrodes, the dual-layer structure cathode exhibits lower activation energy and higher peak power density.

JOURNAL OF PHYSICAL CHEMISTRY C (2021)

添加到收藏夹

Article Chemistry, Physical

Insight into the Electrospinning Process for SOFC Cathode Nanofibers

Junyi Gong et al.

Summary: This study investigates the electrospinning process of LSCF and LSM, finding that adding nitrate to the electrospinning solution affects its viscosity and conductivity, subsequently influencing the size and morphology of nanofibers. Results are expected to serve as a reference for industrializing LSM/LSCF nanofiber electrodes and preparing other SOFC nanofiber cathodes.

JOURNAL OF PHYSICAL CHEMISTRY C (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Electrode/electrolyte interface and interface reactions of solid oxide cells: Recent development and advances

Shuai He et al.

Summary: High temperature solid oxide cells (SOCs) are environmentally friendly and efficient energy conversion technology to store renewable energy and generate electricity. Research has focused on understanding the processes at the electrode/electrolyte interfaces, which play a crucial role in cell performance and durability. Challenges and prospects of interface research for improving SOC device performance and durability are discussed.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Chemistry, Physical

Hydrogen-methanol SOFCs for transport*

Sergey Shcheklein et al.

Summary: The study analyzed the energy efficiency of an installation utilizing high-temperature fuel cells operating on a hydrogen-containing gas mixture obtained from liquid fuel (methanol) through a catalytic process. The electrical efficiency of the installation was found to be 42.1%, equivalent to the energy efficiency level of the best modern internal combustion engines.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Post-Treatment of Screen-Printed Silver Nanowire Networks for Highly Conductive Flexible Transparent Films

Dongdong Li et al.

Summary: Screen printing is an important technique for creating 2D conductive patterns with high conductivity and resolution. Post-treatments introduced into the washing process have successfully achieved high-quality transparent conductive films, maintaining the conductivity of printed networks and the integrity of patterns. High-performance transparent conductive films with extremely low sheet resistance have been achieved by combining plasma treatment, thermal annealing, and high pressure, making screen-printed Ag NW conductive networks promising for next-generation flexible optoelectronic devices.

ADVANCED MATERIALS INTERFACES (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Nb and Cu co-doped (La,Sr)(Co,Fe)O3: a stable electrode for solid oxide cells

D. M. Neacsa et al.

Summary: Solid oxide cells (SOCs) are electrochemical devices that convert chemical energy into electricity. New Cu and Nb co-doped LSCF materials show better conductivity at high temperatures than traditionally used LSCF materials.

RSC ADVANCES (2021)

添加到收藏夹

Article Chemistry, Physical

A-site deficient chromite with in situ Ni exsolution as a fuel electrode for solid oxide cells (SOCs)

Diana-Maria Amaya-Duenas et al.

Summary: The study focused on the synthesis and characterization of A-site deficient lanthanum strontium chromite perovskite La0.65Sr0.3Cr0.85Ni0.15O3-delta (L65SCrN) decorated with Ni nanoparticles for solid oxide cells, as well as evaluating its performance by various analytical techniques. The fuel electrode based on L65SCrN demonstrated comparable electrochemical performance to state-of-the-art Ni-based cermets on an ESC, showing promise for SOC applications. Further research on Ni exsolution in doped chromites is suggested for optimizing the size of Ni nanoparticles.

JOURNAL OF MATERIALS CHEMISTRY A (2021)

添加到收藏夹

Review Energy & Fuels

Fabrication of high-quality electrode films for solid oxide fuel cell by screen printing: A review on important processing parameters

Nurul Akidah Baharuddin et al.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2020)

添加到收藏夹

Article Multidisciplinary Sciences

Electrochemical conversion of methane to ethylene in a solid oxide electrolyzer

Changli Zhu et al.

NATURE COMMUNICATIONS (2019)

添加到收藏夹

Article Materials Science, Ceramics

Printing of NiO-YSZ nanocomposites: From continuous synthesis to inkjet deposition

Massimo Rosa et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Computer Science, Information Systems

A Novel Approach to the Optimization of a Solid Oxide Fuel Cell Anode Using Evolutionary Algorithms

Szymon Buchaniec et al.

IEEE ACCESS (2019)

添加到收藏夹

Article Chemistry, Multidisciplinary

Screen-Printed Poly(3,4-Ethylenedioxythiophene):Poly(Styrenesulfonate) Grids as ITO-Free Anodes for Flexible Organic Light-Emitting Diodes

Lu Zhou et al.

ADVANCED FUNCTIONAL MATERIALS (2018)

添加到收藏夹

Review Chemistry, Multidisciplinary

Printable Transparent Conductive Films for Flexible Electronics

Dongdong Li et al.

ADVANCED MATERIALS (2018)

添加到收藏夹

Article Energy & Fuels

Production of syngas from H2O/CO2 by high-pressure coelectrolysis in tubular solid oxide cells

Muhammad Taqi Mehran et al.

APPLIED ENERGY (2018)

添加到收藏夹

Article Chemistry, Physical

Highly Active Surface Structure in Nanosized Spinel Cobalt-Based Oxides for Electrocatalytic Water Splitting

Jing Zhou et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2018)

添加到收藏夹

Article Chemistry, Physical

Highly durable solid oxide fuel cells: suppressing chemical degradation via rational design of a diffusion-blocking layer

Seunghwan Lee et al.

JOURNAL OF MATERIALS CHEMISTRY A (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Highly efficient electrochemical reforming of CH4/CO2 in a solid oxide electrolyser

Jinhai Lu et al.

SCIENCE ADVANCES (2018)

添加到收藏夹

Article Materials Science, Ceramics

Densification behavior of yttria-stabilized zirconia powders for solid oxide fuel cell electrolytes

Dhruba Panthi et al.

JOURNAL OF ADVANCED CERAMICS (2018)

添加到收藏夹

Article Energy & Fuels

A robust fuel cell operated on nearly dry methane at 500 degrees C enabled by synergistic thermal catalysis and electrocatalysis

Yu Chen et al.

NATURE ENERGY (2018)

添加到收藏夹

Review Green & Sustainable Science & Technology

A review on proton conducting electrolytes for clean energy and intermediate temperature-solid oxide fuel cells

Shahzad Hossain et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)

添加到收藏夹

Review Chemistry, Multidisciplinary

A review of high temperature co-electrolysis of H2O and CO2 to produce sustainable fuels using solid oxide electrolysis cells (SOECs): advanced materials and technology

Yun Zheng et al.

CHEMICAL SOCIETY REVIEWS (2017)

添加到收藏夹

Article Chemistry, Physical

Effects of fabrication parameters on the performance of solid oxide electrolyzer cell

Hatice Korkmaz et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2016)

添加到收藏夹

Article Electrochemistry

Communication-Electrolysis at High Efficiency with Remarkable Hydrogen Production Rates

Anthony Wood et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2016)

添加到收藏夹

Article Physics, Applied

Positron annihilation characterization of free volume in micro- and macro-modified Cu0.4Co0.4Ni0.4Mn1.8O4 ceramics

H. Klym et al.

LOW TEMPERATURE PHYSICS (2016)

添加到收藏夹

Article Engineering, Chemical

Challenges in the development of reversible solid oxide cell technologies: a mini review

San Ping Jiang

ASIA-PACIFIC JOURNAL OF CHEMICAL ENGINEERING (2016)

添加到收藏夹

Proceedings Paper Physics, Applied

Features of X-ray Absorption Densitometry of Large-size Objects with Variable Thickness

S. Osipov et al.

III ALL-RUSSIAN SCIENTIFIC AND PRACTICAL CONFERENCE ON INNOVATIONS IN NON-DESTRUCTIVE TESTING (SIBTEST 2015) (2016)

添加到收藏夹

Article Materials Science, Ceramics

Application of BaO-CaO-Al2O3-B2O3-SiO2 glass-ceramic seals in large size planar IT-SOFC

Linghong Luo et al.

CERAMICS INTERNATIONAL (2015)

添加到收藏夹

Article Chemistry, Physical

Syngas production by high temperature steam/CO2 coelectrolysis using solid oxide electrolysis cells

Xinbing Chen et al.

FARADAY DISCUSSIONS (2015)

添加到收藏夹

Article Chemistry, Physical

Fabrication of thin yttria-stabilized-zirconia dense electrolyte layers by inkjet printing for high performing solid oxide fuel cells

Vincenzo Esposito et al.

JOURNAL OF POWER SOURCES (2015)

添加到收藏夹

Article Chemistry, Physical

Local evolution of anode microstructure morphology in a solid oxide fuel cell after long-term stack operation

Grzegorz Brus et al.

JOURNAL OF POWER SOURCES (2015)

添加到收藏夹

Article Chemistry, Physical

Syngas production by high temperature steam/CO2 coelectrolysis using solid oxide electrolysis cells

Xinbing Chen et al.

FARADAY DISCUSSIONS (2015)

添加到收藏夹

Article Chemistry, Physical

Lignite as a fuel for direct carbon fuel cell system

Janusz Jewulski et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2014)

添加到收藏夹

Article Chemistry, Physical

Preparation of half-cell by bi-layer wet powder spraying and tape casting for anode-supported SOFCs

Lei Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

添加到收藏夹

Article Chemistry, Physical

Enhanced triple-phase boundary density in infiltrated electrodes for solid oxide fuel cells demonstrated by high-resolution tomography

Masashi Kishimoto et al.

JOURNAL OF POWER SOURCES (2014)

添加到收藏夹

Article Chemistry, Physical

Measurement of the temperature distribution in a large solid oxide fuel cell short stack

Selahattin Celik et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanomechanical Properties and Thermal Conductivity Estimation of Plasma-Sprayed, Solid-Oxide Fuel Cell Components: Ceria-Doped, Yttria-Stabilized Zirconia Electrolyte

Neelima Mahato et al.

JOM (2013)

添加到收藏夹

Article Chemistry, Physical

Electrolyte degradation in anode supported microtubular yttria stabilized zirconia-based solid oxide steam electrolysis cells at high voltages of operation

M. A. Laguna-Bercero et al.

JOURNAL OF POWER SOURCES (2011)

添加到收藏夹

Article Materials Science, Ceramics

Preparation and Characterization of (La0.8Sr0.2)0.95MnO3-δ (LSM) Thin Films and LSM/LSCF Interface for Solid Oxide Fuel Cells

Jong-Jin Choi et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2011)

添加到收藏夹

Article Chemistry, Physical

Hydrogen and synthetic fuel production using pressurized solid oxide electrolysis cells

Soren Hojgaard Jensen et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2010)

添加到收藏夹

Article Chemistry, Physical

Quantification of SOFC anode microstructure based on dual beam FIB-SEM technique

Hiroshi Iwai et al.

JOURNAL OF POWER SOURCES (2010)

添加到收藏夹

Article Multidisciplinary Sciences

Impact of Anode Microstructure on Solid Oxide Fuel Cells

Toshio Suzuki et al.

SCIENCE (2009)

添加到收藏夹

Article Chemistry, Physical

On the nanostructuring and catalytic promotion of intermediate temperature solid oxide fuel cell (IT-SOFC) cathodes

Jose M. Serra et al.

JOURNAL OF POWER SOURCES (2007)

添加到收藏夹

Article Chemistry, Physical

Carbon deposition and cell performance of Ni-YSZ anode support SOFC with methane fuel

JH Koh et al.

SOLID STATE IONICS (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.