☆ 4.7 Article

Effect of aging temperature on microstructure and mechanical properties of a novel Ti-6121 alloy

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Variant selection, coarsening behavior of α phase and associated tensile properties in an α plus β titanium alloy

Lei Lei et al.

Summary: The study investigated the effect of cooling rates on variant selection, coarsening behavior of alpha phase, and microstructure evolution in alpha+ beta TC21 alloy. Different microstructure characteristics were observed under air cooling and furnace cooling conditions, leading to variations in tensile properties of the alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Obtaining heterogeneous α laths in selective laser melted Ti-5Al-5Mo-5V-1Cr-1Fe alloy with high strength and ductility

Taomei Zhang et al.

Summary: In this study, direct ageing treatments were used to improve the strength of a selective laser melted titanium alloy. The microstructure and mechanical behavior of the alloy were systematically investigated. It was found that duplex ageing treatment can regulate the microstructure and mechanical properties of the alloy, resulting in improved ductility and ultimate tensile strength.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Strength and ductility optimization of laser additive manufactured metastable β titanium alloy by tuning a phase by post heat treatment

Xiaotong Pang et al.

Summary: The metastable beta titanium alloy TB2 fabricated by laser melting deposition showed good ductility and high ultimate tensile strength. The beta solution plus two-step aging treatment was proved to achieve a good combination of strength and ductility for the TB2 alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced mechanical properties of Ti-5Al-5Mo-5V-3Cr-1Zr by bimodal lamellar precipitate microstructures via two-step aging

Yalong Wang et al.

Summary: A simple two-step aging heat treatment was proposed to design a bimodal microstructure with fine-scale and coarse alpha precipitates in a beta-titanium alloy. The multi-scale alpha microstructure exhibited a synergistic combination of yield strength and ductility, with deformation twins contributing to increased ductility and dislocation tangles contributing to higher strength. This work provides a new strategy to overcome the trade-off between strength and ductility by designing a heterogeneous microstructure.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Engineering, Manufacturing

Effect of heating treatment on the microstructural evolution and dynamic tensile properties of Ti-6Al-4V alloy produced by selective laser melting

Yang Liu et al.

Summary: The paper systematically studied the influence of heating treatment on the microstructure and dynamic tensile properties of Ti-6Al-4 V alloy processed by selective laser melting. It was found that the strength gradually decreased as the heating temperature increased, while the strain to fracture initially increased and then tended to drop after exceeding 13 transus. Good balance of strength and ductility can be achieved with alpha + 13 treatment.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of precursory α and ωphase on microstructure evolution and tensile properties of metastable β titanium alloy

Ruixue Zhang et al.

Summary: The microstructure evolution and tensile properties in a metastable beta titanium alloy, Ti-5Al-5Mo-5V-3Cr-0.6Fe alloy, with different aging conditions were investigated. The results showed that the nanoscale omega phase formed during low-temperature aging had no effect on the tensile properties. Additionally, the small size omega phase failed to assist secondary alpha(s) nucleation and refine alpha(s) during high-temperature aging due to omega dissolution. On the other hand, the alpha phase precipitated during low-temperature aging played a considerable role in refining lamellar alpha(s) and increasing tensile strength.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening

Jiming Lv et al.

Summary: This research investigated the influences of laser shock peening (LSP) on the residual stress state, microstructures, and mechanical properties of Ti-6Al-4V alloy fabricated by selective laser melting (SLM). The results showed that LSP treatment adjusted the residual stress from tensile to compressive state and promoted the formation of high-density dislocations and parallel nano mechanical twins (nano-MTs) in the coarse lamellar alpha' structures, resulting in grain refinement. The ultimate tensile strength and elongation of the SLMed Ti-6Al-4V alloy increased by approximately 14.3% and 18.3% after LSP treatment, respectively. The study revealed that the combination of high levels of compressive residual stress and grain refinement achieved by LSP contributed to the enhancement of both strength and ductility in the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hierarchical structure and deformation behavior of a novel multicomponent β titanium alloy with ultrahigh strength

X. Li et al.

Summary: By utilizing the general [Mo] equivalent criterion and d-electron orbital theory, a new ultrahigh-strength beta titanium alloy TB17 was developed and its microstructure and elements partitioning were systematically investigated. The results demonstrate that the hierarchical structures can be tailored by solution plus aging (STA) heat treatment, leading to superhigh strength and considerable plasticity.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microtexture evolution effected by Mo content in α plus β titanium alloys

Min Qi et al.

Summary: This study investigated the microtexture evolution of alpha in alpha + beta titanium alloys with different Mo content during thermomechanical processing. The results show that the addition of Mo element significantly weakens the microtexture of the prior alpha colony in Ti-6Al-2Sn-4Zr-6Mo (Ti6246) alloy. The study demonstrates the effect of Mo content on the microtexture evolution during thermo-mechanical processing.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Formation and characteristics of bilamellar microstructure in Ti6242S titanium alloy under dual heat treatment

Yu Wang et al.

Summary: This study investigates the formation and characteristics of bilamellar microstructure in Ti6242S titanium alloy under dual heat treatment. It is found that the single-phase heat treatment and cooling process can generate more clusters in the grain boundary and primary lamellar alpha. During two-phase heat treatment, the secondary lamellar alpha nucleates at the grain boundaries or the wide interface of the primary lamellar alpha, and the existing primary lamellar alpha facilitates its formation. V-shaped lamellar alpha and triangular structures are also observed during the heat treatment process.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of duplex aging on microstructure and mechanical properties of near-β titanium alloy processed by isothermal multidirectional forging

Chang-jiang Zhang et al.

Summary: The effects of sub-transus annealing treatment followed by single or duplex aging on the microstructural evolution and mechanical properties of a near-beta titanium alloy were investigated. The results showed that duplex aging resulted in finer secondary alpha phase precipitates, leading to higher strength in the alloy.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Controlling the microstructure and fracture toughness of the Ti-5Al-5Mo-5V-1Cr-1Fe alloy by multiple heat treatments

Zedong Liu et al.

Summary: This study shows the significant influence of microstructure and fracture toughness of the Ti-55511 alloy during STA and STAA heat treatment processes. The proper solution treatment and aging temperature can enhance the toughness of the alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dependence of strength and ductility on secondary a phase in a novel metastable-β titanium alloy

Haoyu Zhang et al.

Summary: This study investigates the correlation between microstructure, strength, and ductility in a novel metastable beta titanium alloy, Ti-6Mo-5V-3Al-2Fe. TEM and SEM were used to observe the secondary alpha phase (alpha(s)) of the aged alloy, and a room temperature tensile test characterized its strength and ductility. The results show that the minimum width and spacing of alpha(s) can be achieved after aging at 470 degrees C for 4h. The study establishes a relational equation between precipitation strengthening and alpha(s) spacing length and demonstrates that the average spacing length of alpha(s) plays a predominant role in the alloy's strengthening. The alloy's ductility is improved by the widening of alpha(s) spacing and the formation of Widmanstaeurotten a phase (WGB alpha) along beta grain boundaries after aging at 620 degrees C for 4h.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

A new β-Ti alloy with good tensile properties by the mixed microstructure characteristics of α phase

Huijin Jin et al.

Summary: This study investigates the mechanical properties, microstructural characteristics, and deformation behavior of a novel high-strength metastable beta alloy. The study demonstrates that by controlling the size, morphology, and orientation combinations of the alpha phase in the beta matrix, a good combination of tensile strength and total elongation can be achieved. The microstructural characteristics of the alpha phase consisting of various alpha structures were obtained through specific heat treatments. The findings suggest that the acicular alpha precipitates act as dislocation barriers, leading to an improvement in the strength of the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Heat treatment effect on the microstructure and elevated temperature tensile property of the Ti6242S alloy fabricated via laser powder bed fusion

Zhiguang Zhu et al.

Summary: The microstructural evolution and the influence of heat treatments on the tensile properties of Ti6242S alloy fabricated via laser powder bed fusion were investigated. The results showed that different heat treatments caused changes in the microstructure and affected the tensile strength of the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Sustaining an excellent strength-ductility combination of a PM α plus β titanium alloy with fine prior β grains and heterogeneous microstructure

Bowen Zhang et al.

Summary: The mechanical properties of two different microstructures of Ti-4Al-4Mo-4Sn-0.5Si alloy were analyzed and compared. The results show that the heterogeneous microstructure exhibits higher tensile yield strength, strain hardening rate, and tensile ductility compared to the homogeneous microstructure with similar high strength.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Engineering, Industrial

Simultaneous improvement of strength and elongation of laser melting deposited Ti-6Al-4V titanium alloy through three-stage heat treatment

Yu Zhou et al.

Summary: This study presents a three-stage heat treatment strategy to improve the strength and ductility of laser melting deposited (LMDed) Ti-6Al-4V titanium alloy. The heat treatment transformed the basketweave microstructure into a multiscale-alpha structure. The good deformation compatibility among the multiscale alpha grains effectively impeded crack propagation and led to an increase in yield strength and elongation.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Chemistry, Physical

Synchronous enhancement of the strength and ductility in a metastable β-Ti alloy by a new refined α phase mechanism

Shuang Hu et al.

Summary: Grain refinement is a method to improve the strength and plasticity of metallic materials. A new alpha grain refinement mechanism was found in hot-rolled metastable beta titanium alloys, leading to significant performance breakthroughs and the balance between strength and ductility.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced strength-ductility synergy in laser additive manufactured TC4 titanium alloy by grain refinement

Xiaotong Pang et al.

Summary: The addition of ZrB2 through laser melting deposition can refine the prior-beta grains in the TC4 titanium alloy, resulting in a fine basket-weave structure. The mechanical anisotropy of the modified-TC4 alloys decreases with the increase of ZrB2 content. The alloy with 0.5 wt% ZrB2 addition shows an excellent combination of strength and ductility, with isotropic characteristics.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Realizing superior ductility of selective laser melted Ti-6Al-4V through a multi-step heat treatment

Cheng-Lin Li et al.

Summary: The study found that a single-step annealing process can change the martensitic structure to a fine lamellar α + β structure, providing a Ti-6Al-4V alloy with high strength and ductility. In contrast, the multi-step heat treatment process facilitates the globularization of the α phase, creating an almost equiaxed structure with superior ductility while maintaining a moderate ultimate tensile strength.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of solution treatment and aging on microstructure, tensile properties and creep behavior of a hot-rolled β high strength titanium alloy with a composition of Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe-0.1B-0.1C

Zhaoqi Chen et al.

Summary: In this study, the microstructure, tensile properties, and creep behavior of a hot-rolled beta high strength Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe-0.1B-0.1C alloy were investigated. It was found that heat treatments had a significant impact on the microstructure evolution, tensile properties, and creep behavior of the alloy. The alloy exhibited the highest strength and showed a combined fracture mechanism, with the alloy solution treated and aged at 560 degrees C demonstrating the lowest steady-stage creep rate and minimal creep strain.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Face centered cubic substructure and improved tensile property in a novel β titanium alloy Ti-5Al-4Zr-10Mo-3Cr

Wenguang Zhu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

The interdependence of microstructure, strength and fracture toughness in a novel β titanium alloy Ti-5Al-4Zr-8Mo-7V

Wenguang Zhu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Balancing strength and ductility by controllable heat-treatment twinning in a near β-Ti alloy

Wei Chen et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced mechanical properties in β-Ti alloy aged from recrystallized ultrafine β grains

Bingjie Zhang et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Slip behavior of Bi-modal structure in a metastable β titanium alloy during tensile deformation

Wenguang Zhu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Breaking through the strength-ductility trade-off dilemma in powder metallurgy Ti-6Al-4V titanium alloy

H. Z. Niu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

A novel high-strength β-Ti alloy with hierarchical distribution of α-phase: The superior combination of strength and ductility

Wenguang Zhu et al.

MATERIALS & DESIGN (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructural dependence of strength and ductility in a novel high strength β titanium alloy with Bi-modal structure

Wenguang Zhu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Chemistry, Physical

Effect of α morphology on the diffusional β ⇆ α transformation in Ti-55531 during continuous heating: Dissection by dilatometer test, microstructure observation and calculation

Fu-Wen Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Correlation between alpha phase morphology and tensile properties of a new beta titanium alloy

S. Sadeghpour et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical property correlation and property optimization of a near β titanium alloy Ti-7333

Jiangkun Fan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Chemistry, Physical

Effect of heat treatment on the microstructure and tensile properties of deformed α/β Ti-47Zr-5Al-3V alloy

Yindong Shi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of hot rolling and heat treatment on microstructure and tensile properties of high strength beta titanium alloy sheets

Z. X. Du et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of heat treatments on microstructure and tensile properties of as-extruded TiBw/near-α Ti composites

B. Wang et al.

MATERIALS & DESIGN (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of heat treatment on microstructure and mechanical properties of a new β high strength titanium alloy

Zhaoxin Du et al.

MATERIALS & DESIGN (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tensile and fracture toughness of high strength β Titanium alloy, Ti-10V-2Fe-3Al, as a function of rolling and solution treatment temperatures

G. Srinivasu et al.

MATERIALS & DESIGN (2013)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.