☆ 4.7 Article

Molecular dynamics simulation on crystal defects of single-crystal silicon during elliptical vibration cutting

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Manufacturing

Deformation behaviors and inverse Hall-Petch effect in nanoindentation of silicon: An atomistic simulation study with experimental validation

Yachao Wang et al.

Summary: This research explores the deformation behaviors of monocrystalline and polycrystalline silicon materials in nanoindentation using atomistic simulation approach. The study validates the molecular dynamics simulation model for nanoindentation, reveals intriguing phenomena like phase transformation and grain size effects, and observes an inverse Hall-Petch effect in the nanoindentation process of silicon.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Engineering, Manufacturing

Molecular dynamics study of crystal orientation effect on surface generation mechanism of single-crystal silicon during the nano-grinding process

Pengyue Zhao et al.

Summary: This study used molecular dynamics simulation method to investigate the nano-grinding process of single-crystal silicon workpieces with different surface crystal orientations, and compared the results with experimental results. It was found that while the machined surface quality was similar for workpieces with different surface crystal orientations, subsurface damage, processing force, phase transition, and residual stress varied significantly. Among the three types of workpieces, the single-crystal silicon workpiece with {110} surface crystal orientation showed the best processing effect.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Chemistry, Physical

Surface deformation, phase transition and dislocation mechanisms of single crystalline 6H-SiC in oblique nano-cutting

Shuo Zhang et al.

Summary: Compared with conventional orthogonal cutting, this study systematically investigates the oblique nano-cutting of 6H-SiC by tilting the tool at different angles through molecular dynamics simulations. The deformation mechanism, surface deformation, and cutting force variation are studied, and the transition path of amorphization is clarified. Dislocation analysis reveals that basal dislocation systems dominate the behavior, while in oblique nano-cutting, the basal 1/3 < 1 (1) over bar 00> Shockley partial dislocation of 6H-SiC is more activated due to the inclined-cutting-edge-derived shear stress.

APPLIED SURFACE SCIENCE (2022)

添加到收藏夹

Article Engineering, Manufacturing

The state of the art for numerical simulations of the effect of the microstructure and its evolution in the metal-cutting processes

Hongguang Liu et al.

Summary: This paper summarizes the state of the art in modeling approaches for the effect of microstructures and their evolution during metal-cutting processes, analyzes the advantages and drawbacks, and provides future research directions.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2022)

添加到收藏夹

Article Engineering, Electrical & Electronic

Study of deformation mechanism of structural anisotropy in 4H-SiC film by nanoindentation

Lianghao Xue et al.

Summary: This study systematically investigated the deformation mechanism of structural anisotropy in 4H-SiC film on different indentation planes, revealing that the hardness and Young's modulus vary on different planes and the formation of defects and dislocations depends on the specific indentation plane.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2022)

添加到收藏夹

Article Engineering, Mechanical

Effects of grain size and protrusion height on the surface integrity generation in the nanogrinding of 6H-SiC

Zhonghuai Wu et al.

Summary: This paper investigates the effects of non-uniform abrasive grains on the deformation and material removal mechanisms of 6H-SiC during nanogrinding using molecular dynamics simulations. The study finds that different sizes of abrasive grains and cutting depths can result in different grinding mechanisms, which in turn affect the plastic deformation of the material.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Article Engineering, Manufacturing

Investigation of surface integrity transition of SiCp/Al composites based on specific cutting energy during ultrasonic elliptical vibration assisted cutting

Jiakang Zhou et al.

Summary: This study investigates the surface integrity transition of SiCp/Al composites during ultrasonic elliptical vibration-assisted cutting (UEVC) and establishes a quantitative criterion to evaluate the surface integrity. Experimental results show that the cutting speed and processing method have a significant impact on the surface integrity of SiCp/Al composites.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Materials Science, Ceramics

Atomistic investigation of machinability of monocrystalline 3C-SiC in elliptical vibration-assisted diamond cutting

Liang Zhao et al.

Summary: The study reveals the mechanisms governing machined surface formation of hard brittle monocrystalline 3C-SiC in ultrasonic elliptical vibration-assisted diamond cutting through molecular dynamics simulations. Different deformation modes and their correlations with surface integrity are shown.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Instruments & Instrumentation

Investigation of surface integrity and material removal mechanism of single-crystal Si subjected to micro-laser-assisted machining

Ruiwen Geng et al.

Summary: A three-dimensional transient thermal model was developed to investigate temperature responses in μ-LAM processing of single-crystal Si, where dislocation motion velocity increased to approximately 2.57 x 10(9) times, facilitating ductile deformation. Residual stress significantly decreased with μ-LAM, increasing rotation speed aided ductile machining and suppressed micro-pits, while surface roughness and amorphous layer thickness decreased with increased rotation speed.

INFRARED PHYSICS & TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Effect of abrasive grain position patterns on the deformation of 6H-silicon carbide subjected to nano-grinding

Zhonghuai Wu et al.

Summary: This study used molecular dynamics simulations to investigate the influence of grain position patterns on the deformation of 6H-SiC. It was found that the plastic deformation of 6H-SiC is characterized by a thin amorphous layer at the surface and dislocations in the subsurface, with details varying depending on grain position patterns and gaps.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dynamic mechanical contact behaviors and sintering mechanism of Al nanoparticles subjected to high-speed impact

Jun Jiang et al.

Summary: The research found that Al nanoparticles transform from long-range ordered structure to short-range ordered structure and eventually into amorphous structure under high-speed impact, with a critical speed at which the atoms completely transform into amorphous structure. Surface atoms exhibit larger displacement than internal atoms during head-on impact, and various parameters experience different changes at different initial impact speeds.

MATERIALS CHEMISTRY AND PHYSICS (2021)

添加到收藏夹

Article Engineering, Electrical & Electronic

Numerical investigation on material removal mechanism in elliptical vibration cutting of single-crystal silicon

Changlin Liu et al.

Summary: The study utilized molecular dynamics simulation to investigate the material removal mechanism in single crystal silicon EVC, revealing a shift from extrusion to shear as the dominant material removal mechanism within a single vibration cycle. Furthermore, the formation mechanism of subsurface damage in extrusion and shear stages was analyzed, along with the factors influencing the extrusion to shear transition.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2021)

添加到收藏夹

Article Engineering, Mechanical

Structural anisotropy effect on the nanoscratching of monocrystalline 6H-silicon carbide

Zhonghuai Wu et al.

Summary: This paper comprehensively studied the structural anisotropy effect on the nanoscratching of 6H-SiC using large-scale molecular dynamics simulations. Different combinations of scratching conditions resulted in significant variations in scratching-induced deformation morphology, activated dislocations, and scratching forces due to the strong anisotropy effect of the material. The basal plane (0001) along < 1100 > direction was identified as the best combination for conducting nanoscratching on 6H-SiC.

WEAR (2021)

添加到收藏夹

Article Chemistry, Physical

Machining mechanism and deformation behavior of high-entropy alloy under elliptical vibration cutting

Dinh-Quan Doan et al.

Summary: The study revealed that both strain and stress are concentrated at the contact area between the workpiece and cutting tool, as well as at the grain boundaries, under both conventional cutting and ultrasonic elliptical vibration-assisted cutting. Molecular dynamics simulation showed that the temperature of the workpiece is significantly higher under UEVAC, which can facilitate phase transformation and make the cutting process easier. Additionally, the deformation behavior of polycrystalline materials is strongly influenced by grain boundaries, and the cutting force under UEVAC decreases with increasing vibration frequency and amplitude ratio.

INTERMETALLICS (2021)

添加到收藏夹

Article Automation & Control Systems

Effect of tool rake angle on the material removal mechanism transition of single-crystal silicon: a molecular dynamics study

Changlin Liu et al.

Summary: With a decrease in tool rake angle, the material removal mechanism shifts from shear to extrusion, and ultimately no material is removed. The transition from shear to extrusion is greatly influenced by the tool rake angle and workpiece crystal orientation, while the transition from extrusion to no removal is mainly affected by the position of the stagnation region and frictional force on the tool rake face.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Manufacturing

Surface generation of tungsten carbide in laser-assisted diamond turning

Kaiyuan You et al.

Summary: The study investigates the removal mechanism of binderless polycrystalline tungsten carbide material through conventional cutting and in-process-heat laser-assisted cutting. The results show that the high-temperature nanoindentation test reveals improved machinability of WC at an elevated temperature, and the optimal laser power for obtaining a better surface finish ranges from 10 W to 15 W.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

添加到收藏夹

Article Engineering, Manufacturing

Numerical investigation on subsurface damage in nanometric cutting of single-crystal silicon at elevated temperatures

Changlin Liu et al.

Summary: The lubricant effect of the amorphous layer and the recrystallization process are determined as two important reasons for suppressing subsurface damage at high cutting temperature on single-crystal silicon.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Materials Science, Ceramics

Amorphization-governed elasto-plastic deformation under nanoindentation in cubic (3C) silicon carbide

Liang Zhao et al.

CERAMICS INTERNATIONAL (2020)

添加到收藏夹

Article Engineering, Electrical & Electronic

Atomistic simulation of influence of laser nano-structured diamond abrasive on the polishing behavior of silicon

Houfu Dai et al.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2020)

添加到收藏夹

Article Engineering, Chemical

Dynamic mechanical contact behaviours of amorphous nanoparticles subjected to high-speed impact

Weifu Sun et al.

POWDER TECHNOLOGY (2020)

添加到收藏夹

Article Automation & Control Systems

A simulation investigation on elliptical vibration cutting of single-crystal silicon

Changlin Liu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Industrial

On ductile-regime elliptical vibration cutting of silicon with identifying the lower bound of practicable nominal cutting velocity

Jianjian Wang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Manufacturing

Molecular dynamics simulation of the material removal in the scratching of 4H-SiC and 6H-SiC substrates

Zige Tian et al.

INTERNATIONAL JOURNAL OF EXTREME MANUFACTURING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Monitoring micro-structural evolution during aluminum sintering and understanding the sintering mechanism of aluminum nanoparticles: A molecular dynamics study

Jun Jiang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Automation & Control Systems

Influence of elliptical vibration on the behavior of silicon during nanocutting

Houfu Dai et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

添加到收藏夹

Article Engineering, Mechanical

Study on strain rate and heat effect on the removal mechanism of SiC during nano-scratching process by molecular dynamics simulation

Binbin Meng et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

A numerical study on subsurface quality and material removal during ultrasonic vibration assisted cutting of monocrystalline silicon by molecular dynamics simulation

Houfu Dai et al.

MATERIALS RESEARCH EXPRESS (2019)

添加到收藏夹

Article Engineering, Manufacturing

Heat effect on the material removal in the machining of fibre-reinforced polymer composites

Weixing Xu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Amorphization induced by 60° shuffle dislocation pileup against different grain boundaries in silicon bicrystal under shear

Hao Chen et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Automation & Control Systems

Observed edge radius behavior during MD nanomachining of silicon at a high uncut chip thickness

Lukman N. Abdulkadir et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

添加到收藏夹

Article Chemistry, Physical

A numerical study on the material removal and phase transformation in the nanometric cutting of silicon

Jinshi Wang et al.

APPLIED SURFACE SCIENCE (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of recovery and side flow on surface generation in nano-cutting of single crystal silicon

Feifei Xu et al.

COMPUTATIONAL MATERIALS SCIENCE (2018)

添加到收藏夹

Article Automation & Control Systems

A study on the tool edge geometry effect on nano-cutting

Feifei Xu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Molecular Dynamics Modeling and Simulation of Diamond Cutting of Cerium

Junjie Zhang et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Side Flow Effect on Surface Generation in Nano Cutting

Feifei Xu et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Anisotropy of Single-Crystal Silicon in Nanometric Cutting

Zhiguo Wang et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Article Chemistry, Multidisciplinary

A study on the surface quality and brittle-ductile transition during the elliptical vibration-assisted nanocutting process on monocrystalline silicon via molecular dynamic simulations

Bo Zhu et al.

RSC ADVANCES (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Molecular Dynamics Modeling and Simulation of Diamond Cutting of Cerium

Junjie Zhang et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Side Flow Effect on Surface Generation in Nano Cutting

Feifei Xu et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Anisotropy of Single-Crystal Silicon in Nanometric Cutting

Zhiguo Wang et al.

NANOSCALE RESEARCH LETTERS (2017)

添加到收藏夹

Editorial Material Energy & Fuels

Better than ever

Pierre-Jean Ribeyron

NATURE ENERGY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interaction between phase transformations and dislocations at incipient plasticity of monocrystalline silicon under nanoindentation

Junjie Zhang et al.

COMPUTATIONAL MATERIALS SCIENCE (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of microstructure on the cutting behaviour of silicon

Saurav Goel et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Amorphization and nanocrystallization of silicon under shock compression

S. Zhao et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of tool geometry on subsurface damage and material removal in nanometric cutting single-crystal silicon by a molecular dynamics simulation

Houfu Dai et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

An atomistic simulation investigation on chip related phenomena in nanometric cutting of single crystal silicon at elevated temperatures

Saeed Zare Chavoshi et al.

COMPUTATIONAL MATERIALS SCIENCE (2016)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

Global transition path search for dislocation formation in Ge on Si(001)

E. Maras et al.

COMPUTER PHYSICS COMMUNICATIONS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Molecular dynamics simulation study of deformation mechanisms in 3C-SiC during nanometric cutting at elevated temperatures

Saeed Zare Chavoshi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Engineering, Electrical & Electronic

Molecular dynamics study on the thickness of damage layer in multiple grinding of monocrystalline silicon

Xiaoguang Guo et al.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2016)

添加到收藏夹

Article Engineering, Electrical & Electronic

Dislocation-mediated plasticity in silicon during nanometric cutting: A molecular dynamics simulation study

Saeed Zare Chavoshi et al.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2016)

添加到收藏夹

Article Chemistry, Physical

Subsurface damage mechanism of high speed grinding process in single crystal silicon revealed by atomistic simulations

Jia Li et al.

APPLIED SURFACE SCIENCE (2015)

添加到收藏夹

Article Engineering, Mechanical

Pressure and shear-induced amorphization of silicon

S. Zhao et al.

EXTREME MECHANICS LETTERS (2015)

添加到收藏夹

Article Chemistry, Multidisciplinary

Flexible Single-Crystal Silicon Nanomembrane Photonic Crystal Cavity

Xiaochuan Xu et al.

ACS NANO (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Computational Analysis Methods in Atomistic Modeling of Crystals

Alexander Stukowski

JOM (2014)

添加到收藏夹

Article Engineering, Industrial

Fundamental investigation of ultra-precision ductile machining of tungsten carbide by applying elliptical vibration cutting with single crystal diamond

Jianguo Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)

添加到收藏夹

Review Nanoscience & Nanotechnology

Silicon nanostructures for photonics and photovoltaics

Francesco Priolo et al.

NATURE NANOTECHNOLOGY (2014)

添加到收藏夹

Article Automation & Control Systems

Modeling of the effect of tool edge radius on surface generation in elliptical vibration cutting

Xinquan Zhang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)

添加到收藏夹

Article Chemistry, Physical

Research on the effects of machining-induced subsurface damages on mono-crystalline silicon via molecular dynamics simulation

Hongwei Zhao et al.

APPLIED SURFACE SCIENCE (2012)

添加到收藏夹

Article Nanoscience & Nanotechnology

Nanotwinning in monocrystalline silicon upon nanoscratching

Kausala Mylvaganam et al.

SCRIPTA MATERIALIA (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Visualization and analysis of atomistic simulation data with OVITO-the Open Visualization Tool

Alexander Stukowski

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Extracting dislocations and non-dislocation crystal defects from atomistic simulation data

Alexander Stukowski et al.

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2010)

添加到收藏夹

Article Engineering, Multidisciplinary

Fundamental investigation of subsurface damage in single crystalline silicon caused by diamond machining

Jiwang Yan et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2009)

添加到收藏夹

Article Engineering, Industrial

Analysis of 3D elliptical vibration cutting with thin shear plane model

E. Shamoto et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)

添加到收藏夹

Article Engineering, Mechanical

Characteristics of dynamic hard particles in nanoscale ductile mode cutting of monocrystalline silicon with diamond tools in relation to tool groove wear

M. B. Cai et al.

WEAR (2007)

添加到收藏夹

Article Engineering, Industrial

A study on mechanism of nano-cutting single crystal silicon

F. Z. Fang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Analytical potential for atomistic simulations of silicon, carbon, and silicon carbide

P Erhart et al.

PHYSICAL REVIEW B (2005)

添加到收藏夹

Article Nanoscience & Nanotechnology

Molecular dynamics simulation of phase transformations in silicon monocrystals due to nano-indentation

WCD Cheong et al.

NANOTECHNOLOGY (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.