4.5 Article

Effect of locating the atomizer at the inlet in fountain confined conical spouted beds for drying kaolin suspensions

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Engineering, Chemical

Bed symmetry in the fountain confined conical spouted beds with open-sided draft tubes

Mikel Tellabide et al.

Summary: Bed symmetry in fountain confined conical spouted beds operating with fine particles has been analyzed, showing different effects under various conditions, especially when open-sided draft tubes are used, leading to differences in bed symmetry.

POWDER TECHNOLOGY (2022)

Article Energy & Fuels

Sawdust drying in a series of rectangular base spouted beds using solar energy

A. Reyes et al.

Summary: This study reports experimental results and statistical analysis of sawdust drying using solar energy and phase change materials. The results show that the optimal operating conditions of the dryer can effectively remove moisture from the sawdust and can be sustained for at least 4 hours.

JOURNAL OF ENERGY STORAGE (2022)

Article Food Science & Technology

Dynamic changes of non-volatile compounds and evaluation on umami during infrared assisted spouted bed drying of shiitake mushrooms

Yiming Xu et al.

Summary: This study investigates the dynamic changes of non-volatile components and umami evaluation of shiitake mushrooms during infrared-assisted spouted bed drying (IRSBD). The results show that the drying temperature has a significant effect on drying characteristics, while airflow speed affects the flavor components. The optimal conditions for dehydrating shiitake mushrooms and producing high-quality dried products with rich flavor are a temperature of 55°C and airflow speeds of 8.0-8.5 m/s.

FOOD CONTROL (2022)

Article Engineering, Chemical

Mass transfer in conical spouted beds equipped with internal devices

Xabier Sukunza et al.

Summary: The gas-solid contact in spouted beds is characterized by high heat and mass transfer rates. The mass transfer coefficient in conical spouted beds equipped with internal devices can be accurately predicted using a new correlation that takes into account bed material properties, air inlet temperature and velocity, and dimensions of the internals.

POWDER TECHNOLOGY (2022)

Article Thermodynamics

Pyrolysis of plastic wastes in a fountain confined conical spouted bed reactor: Determination of stable operating conditions

Santiago Orozco et al.

Summary: This study aims to determine the optimal conditions for stable operation in the pyrolysis of waste plastics, focusing on improving gas-solid contact. The research results indicate that polymers with low decomposition temperatures or high branching degrees require lower operating temperatures, and increasing the bed mass to plastic feed rate ratio and spouting velocity can reduce the temperature needed to avoid defluidization. Additionally, the use of a catalyst can effectively lower the temperature required for stable operation by reducing the activation energy of cracking reactions.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Engineering, Chemical

Drying of particulate materials in draft tube conical spouted beds: Energy analysis

Ronaldo Correia de Brito et al.

Summary: The study conducted an energy analysis of a draft tube conical spouted bed for particulate materials and found that the nonporous tube provided the best energy performance for diffusive materials like barley and soybean particles.

POWDER TECHNOLOGY (2021)

Article Engineering, Chemical

Continuous drying of fine and ultrafine sands in a fountain confined conical spouted bed

Xabier Sukunza et al.

Summary: This study analyzed the performance of a fountain confined conical spouted bed in the continuous drying of fine and ultrafine sands, finding that fine sand has higher drying capacity and the best energy utilization can be achieved with high sand flow rates.

POWDER TECHNOLOGY (2021)

Article Engineering, Chemical

New operation regimes in fountain confined conical spouted beds

Mikel Tellabide et al.

CHEMICAL ENGINEERING SCIENCE (2020)

Article Engineering, Chemical

Parametrization of particle coating process with chitosan in spouted bed

Ferreira Mariana Avila et al.

PARTICULATE SCIENCE AND TECHNOLOGY (2020)

Article Engineering, Chemical

Effect of the Solid Inlet Design on the Continuous Drying of Fine and Ultrafine Sand in a Fountain Confined Conical Spouted Bed

Xabier Sukunza et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2020)

Article Energy & Fuels

Design Factors in Fountain Confined Conical Spouted Beds

Idoia Estiati et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2020)

Article Engineering, Chemical

Minimum spouting velocity of fine particles in fountain confined conical spouted beds

Mikel Tellabide et al.

POWDER TECHNOLOGY (2020)

Article Engineering, Chemical

Drying of pasty and granular materials in mechanically and conventional spouted beds

Robson C. Sousa et al.

PARTICUOLOGY (2019)

Article Engineering, Chemical

Pharmaceutical applications of spouted beds: A review on solid dosage forms

Luis Alexandre Pedro de Freitas

PARTICUOLOGY (2019)

Article Engineering, Chemical

Fine particle entrainment in fountain confined conical spouted beds

I. Estiati et al.

POWDER TECHNOLOGY (2019)

Article Engineering, Chemical

Analysis of the dynamics of paste drying in a spouted bed

Carlos Adriano Moreira da Silva et al.

DRYING TECHNOLOGY (2019)

Article Thermodynamics

A new correlation for minimum spouting velocity for conical spouted beds operating with high density particles

Shahab Golshan et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2018)

Article Engineering, Chemical

Study of model application for drying of pulp fruit in spouted bed with intermittent feeding and accumulation

Thayse Naianne Pires Dantas et al.

DRYING TECHNOLOGY (2018)

Article Engineering, Chemical

Fountain confined conical spouted beds

Haritz Altzibar et al.

POWDER TECHNOLOGY (2017)

Article Engineering, Chemical

Minimum spouting velocity for conical spouted beds of vegetable waste biomasses

Juan F. Saldarriaga et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2016)

Article Engineering, Chemical

Operating and Peak Pressure Drops in Conical Spouted Beds Equipped with Draft Tubes of Different Configuration

Haritz Altzibar et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2014)

Article Engineering, Chemical

Moisture Prediction During Paste Drying in a Spouted Bed

B. S. Nascimento et al.

DRYING TECHNOLOGY (2013)

Article Engineering, Chemical

Minimum Spouting Velocity of Conical Spouted Beds Equipped with Draft Tubes of Different Configuration

Haritz Altzibar et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2013)

Article Engineering, Chemical

A Review on Paste Drying with Inert Particles as Support Medium

J. T. Freire et al.

DRYING TECHNOLOGY (2012)

Article Engineering, Chemical

Transient Analysis of Pasty Material Drying in a Spouted Bed of Inert Particles

A. R. F. Almeida et al.

DRYING TECHNOLOGY (2010)

Article Engineering, Chemical

Drying of suspensions and solutions on inert particle surface in mechanically spouted bed dryer

Elisabeth Pallai-Varsanyi et al.

CHINA PARTICUOLOGY (2007)

Article Engineering, Chemical

Coating and drying in spouted bed: Influence of the liouid-particle work of adhesion

M. W. Donida et al.

DRYING TECHNOLOGY (2007)

Article Engineering, Chemical

Experimental analysis of a mechanically stirred spouted bed dryer

A Reyes et al.

DRYING TECHNOLOGY (2000)