☆ 4.7 Article

On accurate characterization of interfacial morphology and damage evolution of thermoplastic composite welded joints: A microscale study via in-situ micro-CT

COMPOSITES SCIENCE AND TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Mechanics

Experimental and numerical evaluation of conduction welded thermoplastic composite joints

B. H. A. H. Tijs et al.

Summary: This study investigates the strength and failure behavior of conduction welded thermoplastic composite joints through numerical and experimental evaluation. The research finds that the joint strength is highly influenced not only by the failure mechanisms of the welded interface but also of the surrounding plies. The high-fidelity modeling methodology can predict the experimental failure mode of welded joints with high accuracy and offers new insights into the key variables influencing the strength of thermoplastic welded joints.

COMPOSITE STRUCTURES (2022)

添加到收藏夹

Article Materials Science, Composites

Low velocity impact resistance of thin and toughened carbon fibre reinforced epoxy

Andreas Klingler et al.

Summary: This study investigates the effect of core-shell rubber nanoparticle and block copolymer matrix modifications on the low velocity impact resistance of thin, multi-axial carbon fibre reinforced epoxy laminates. The results show that the damage resistance is greatly enhanced to impact energies of 9 J and 13 J, but a proper bonding between matrix and the embedded fibres is essential. Lower impact energies do not activate the toughening agents effectively.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Manufacturing

Improving the quality of continuous ultrasonically welded thermoplastic composite joints by adding a consolidator to the welding setup

Bram Jongbloed et al.

Summary: Continuous ultrasonic welding is a promising technique for joining thermoplastic composite structures, but current research shows the presence of deconsolidation voids at the welding interface, leading to reduced strength. This study aims to improve weld quality by adding a consolidation shoe to the welding setup and determines the optimal consolidation pressure, shoe size, and distance from the sonotrode through a stepwise approach. Results show that the furthest consolidation distance achieves high-quality welds with minimal porosity and high strength.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

添加到收藏夹

Article Engineering, Manufacturing

The effects of misaligned adherends on static ultrasonic welding of thermoplastic composites

C. B. G. Brito et al.

Summary: This research investigates the influence of misaligned adherends on static ultrasonic welding of thermoplastic composites by creating different angles through changing the clamping configuration. The results show that increasing the angle between adherends decreases power consumption, increases process time, decreases weld uniformity, and increases the risk of overheating. Reducing the top adherends' bending stiffness by increasing the clamping distance significantly reduces the adverse effects of adherend misalignment on weld quality.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

添加到收藏夹

Article Engineering, Biomedical

Ultrasonic welding of polyetheretherketone for dental applications

Nesreen Abdulfattah et al.

Summary: This study aimed to determine the optimal welding parameters for different dental PEEK grades using ultrasonic welding in order to achieve maximum weld strength. The results showed that increasing welding energy led to increased welding time and surface deformation, while a reasonable welding energy resulted in higher shear bond strength.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2022)

添加到收藏夹

Article Engineering, Manufacturing

Texture and intermetallic compounds of the Cu/Al dissimilar joints by high power ultrasonic welding

Jian Liu et al.

Summary: This study systematically investigated the microstructure and intermetallic compounds of Cu/Al joints produced by high power ultrasonic welding (HUSW). The research found that the welding time had little effect on the grain morphology and size of pure copper, but had a significant impact on the aluminum alloy. Moreover, the texture characteristics of copper and aluminum alloy also changed during the welding process.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Materials Science, Composites

Leakage performance of CFRP laminate under cryogenic temperature: Experimental and simulation study

Jinxin Meng et al.

Summary: This paper experimentally assesses the leakage properties of CFRP laminates with various lay-up configurations under different loads and temperatures. It also discusses the effects of temperature, cooling conditions, and loading on the leakage rates, while characterizing the internal microstructure evolution and defects of the composites. A novel 3D image-based model is developed to predict the leakage properties of the composites under various loads.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Computer Science, Artificial Intelligence

A multi-view clustering framework via integrating K-means and graph- cut

Han Lu et al.

Summary: This study proposes a multi-view clustering framework based on K-means and graph, and develops an efficient clustering method. The method calculates the discrete cluster assignment matrix directly and considers the different contributions of views using an auto-weighted strategy. It fits both Gaussian and non-Gaussian distributed datasets.

NEUROCOMPUTING (2022)

添加到收藏夹

Review Engineering, Industrial

Review of the advancements in aluminum and copper ultrasonic welding in electric vehicles and superconductor applications

Michael de Leon et al.

Summary: This paper reviews the current status of ultrasonic welding (UW) for joining aluminum and copper in electric vehicle batteries and superconductors. It addresses important issues such as process characteristics, weld parameter optimization, joint structure morphology, temperature measurements, joint mechanical properties, and quality of the joints. The paper also discusses the use of finite element method for modeling and simulations in predicting the physical phenomena in the dynamic UW process. Additionally, it provides guidelines and valuable knowledge for the integration of UW in electric vehicle battery assembly and superconductors.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

A review study in ultrasonic-welding of similar and dissimilar thermoplastic polymers and its composites

T. G. Unnikrishnan et al.

Summary: Due to the use of integrated materials in various fields, there is a growing demand for new technologies and the ultrasonic joining method has become important. Ultrasonic welding is fast and energy efficient, particularly for thermoplastic composites.

MATERIALS TODAY-PROCEEDINGS (2022)

添加到收藏夹

Article Mechanics

Morphology characterization and in-situ three-dimensional strain fi eld monitor of short carbon fi ber -reinforced polymer composites under tension

Panding Wang et al.

Summary: By combining high and low resolution ?CT scans, this study successfully monitored the 3D geometric morphology and deformation fields of SCFRP composites under different tension states, and determined the influence of micro geometric morphology on material fracture behavior.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Lab-based in-situ micro-CT observation of gaps in prepreg laminates during consolidation and cure

James Kratz et al.

Summary: An experimental technique was developed to obtain 3D microstructural information on typical lay-up features in automated fibre placement or automated tape laying, with a focus on parallel-ply gaps and ply-drop gaps. Using lab-based CT scanning, different mechanisms of squeezing and bleeding during the manufacturing process were observed. The study found that parallel-ply gaps consolidate faster and reach lower porosity levels compared to ply-drop gaps, but previously consolidated voids may reappear and remain in the final microstructure.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Enhancing weld attributes in ultrasonic spot welding of carbon fibre-reinforced thermoplastic composites: Effect of sonotrode configurations and process control

Tian Zhao et al.

Summary: The research aims to improve the manufacturing efficiency and weld attributes of ultrasonic spot welded joints by adopting proper sonotrodes combined with process control techniques. It was conducted in two steps, first using sonotrodes with different diameters for single-spot ultrasonic welding, then proposing a simultaneous spot welding technique for two welded spots. Results showed that increasing sonotrode size and using proper welding force can significantly enhance welding efficiency and attributes.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Mechanics

Characterisation of damage evolution in plain weave SiC/SiC composites using in situ X-ray micro-computed tomography

Daxu Zhang et al.

Summary: This paper investigates the microstructures and tensile damage evolution of plain weave SiC fibre reinforced SiC matrix composites using X-ray computed tomography. The study reveals the initiation and evolution of material damages using deep-learning-based image segmentation. Results show that longitudinal matrix cracking is more severe than transverse cracking, and the lengths of fibre pull-outs at the fracture surface of fibre tows vary widely.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Characterisation of void and fiber distribution in 3D printed carbon-fiber/PEEK using X-ray computed tomography

S. Sommacal et al.

Summary: The study found that the 3D printing process did not eliminate the voids present in the feedstock filament, and the variation of key printing parameters had minor effects on void content in the printed samples. However, the depositional nature of the printing process strongly influenced the internal geometry of the samples.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Chemistry, Physical

3D X-ray Microscopy of Ultrasonically Welded Aluminum/Fiber-Reinforced Polymer Hybrid Joints

Florian Staab et al.

Summary: The study analyzed ultrasonically welded hybrid aluminum/fiber-reinforced PEEK joints non-destructively with an X-ray microscope to investigate the potential and limitations of the technology as a non-destructive testing method. The joints with suitable and unsuitable parameters were compared quantitatively, and the influence of geometric modifications on the resulting hybrid joints was examined on a microscopic level. The use of a tool for 3D segmentation provided quantitative information on volume-specific proportions for comparison.

MATERIALS (2021)

添加到收藏夹

Article Agriculture, Multidisciplinary

Recognition of early blight and late blight diseases on potato leaves based on graph cut segmentation

Chaojun Hou et al.

Summary: This study proposed an accurate method for recognizing diseases on potato leaves, utilizing an automatic scheme for image segmentation and feature extraction, evaluating performance with various classifiers, and achieving successful recognition of potato diseases and infection degrees.

JOURNAL OF AGRICULTURE AND FOOD RESEARCH (2021)

添加到收藏夹

Article Engineering, Manufacturing

Characterization of multilayer ultrasonic welding based on the online monitoring of sonotrode displacement

Zunnong Ma et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Investigation and characterization of ultrasonically welded GF/PA6T composites

R. Kalyan Kumar et al.

MATERIALS TODAY-PROCEEDINGS (2020)

添加到收藏夹

Article Engineering, Manufacturing

On sequential ultrasonic spot welding as an alternative to mechanical fastening in thermoplastic composite assemblies: A study on single-column multi-row single-lap shear joints

Tian Zhao et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)

添加到收藏夹

Article Engineering, Manufacturing

Shear and tensile joint strengths of carbon fiber-reinforced thermoplastics using ultrasonic welding

Keita Goto et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)

添加到收藏夹

Article Engineering, Manufacturing

Influence mechanism of welding time and energy director to the thermoplastic composite joints by ultrasonic welding

Wang Tao et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of environmental conditions on the resistance of damaged composite materials

Sidi Mohammed Amine Khiat et al.

FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY (2019)

添加到收藏夹

Article Engineering, Manufacturing

Towards robust sequential ultrasonic spot welding of thermoplastic composites: Welding process control strategy for consistent weld quality

Tian Zhao et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

添加到收藏夹

Article Engineering, Manufacturing

Processability and tensile performance of continuous glass fiber/polyamide laminates for structural load-bearing applications

M. Nikforooz et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

添加到收藏夹

Article Engineering, Manufacturing

A study on amplitude transmission in ultrasonic welding of thermoplastic composites

Genevieve Palardy et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

添加到收藏夹

Article Engineering, Manufacturing

Characterization of weld attributes in ultrasonic welding of short carbon fiber reinforced thermoplastic composites

Kaifeng Wang et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

添加到收藏夹

Article Materials Science, Composites

On the effect of flat energy directors thickness on heat generation during ultrasonic welding of thermoplastic composites

Genevieve Palardy et al.

COMPOSITE INTERFACES (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Opposite role of different carbon fiber reinforcements on the non-isothermal crystallization behavior of poly(etheretherketone)

Marco Regis et al.

MATERIALS CHEMISTRY AND PHYSICS (2016)

添加到收藏夹

Article Engineering, Manufacturing

Microstructure, welding mechanism, and failure of Al/Cu ultrasonic welds

Xin Wu et al.

JOURNAL OF MANUFACTURING PROCESSES (2015)

添加到收藏夹

Article Materials Science, Composites

In situ monitoring of ultrasonic welding of thermoplastic composites through power and displacement data

Irene Fernandez Villegas

JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2015)

添加到收藏夹

Article Engineering, Manufacturing

Strength development versus process data in ultrasonic welding of thermoplastic composites with flat energy directors and its application to the definition of optimum processing parameters

Irene Fernandez Villegas

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2014)

添加到收藏夹

Article Materials Science, Composites

Micro-CT investigation on fatigue damage evolution in short fibre reinforced polymers

F. Cosmi et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2013)

添加到收藏夹

Article Materials Science, Composites

Process and performance evaluation of ultrasonic, induction and resistance welding of advanced thermoplastic composites

Irene Fernandez Villegas et al.

JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2013)

添加到收藏夹

Article Engineering, Multidisciplinary

X-ray radiography and micro-computed tomography examination of damage characteristics in stitched composites subjected to impact loading

K. T. Tan et al.

COMPOSITES PART B-ENGINEERING (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

X-ray tomography observation of crack propagation in nuclear graphite

A. Hodgkins et al.

MATERIALS SCIENCE AND TECHNOLOGY (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.