☆ 4.7 Article

Quantitative thermomechanical characterisation of 3D-woven SiC/SiC composites from in-situ tomographic and thermographic imaging

COMPOSITE STRUCTURES (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Multidisciplinary

Disclosing residual thermal stresses in UHT fibre-reinforced ceramic composites and their effect on mechanical behaviour and damage evolution

Pietro Galizia et al.

Summary: The impact of residual thermal stresses (RTS) on the reusability of CMCs with high-temperature capabilities and ablation resistance was studied. The RTS of ZrB2-SiC ceramic reinforced with carbon fibers was found to depend on fiber anisotropy and fiber coating. Microstructural analysis revealed the presence of residual porosity, cracks, porosity within fiber bundles, volumetric content of the fibers, and degree of dispersion. The level of RTS was determined by comparing stiffness-displacement curves and cyclic dilatometric curves, and its correlation with thermomechanical behavior was evaluated through flexural tests.

COMPOSITES PART B-ENGINEERING (2023)

添加到收藏夹

Article Instruments & Instrumentation

In situ tomographic study of a 3D-woven SiC/SiC composite part subjected to severe thermo-mechanical loads

Leonard Turpin et al.

Summary: In this study, a high-temperature multi-axial test was conducted to characterize the thermomechanical behavior of a 3D-woven SiC/SiC composite aeronautical part. The results showed that the mesostructure had an influence on fracture phenomena under realistic operating conditions.

JOURNAL OF SYNCHROTRON RADIATION (2022)

添加到收藏夹

Article Engineering, Manufacturing

Numerical modeling of 3D woven composite reinforcements: A review

Yanneck Wielhorski et al.

Summary: The literature on numerical modeling of 3D woven composite reinforcements has seen a wide range of studies in the last two decades, with two distinct strategies emerging: predictive approaches involving mechanical constructions and numerical simulations, and descriptive approaches focusing on extracting real textile geometry. Different strategies have been employed for yarn behavior modeling at different scales, with a proposed common terminology for organizing and discussing strategies.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

添加到收藏夹

Article Materials Science, Ceramics

In situ observation of the capillary infiltration of molten silicon in a SiC/SiC composite by X-ray radiography

H. Carpentier et al.

Summary: Capillary infiltration is an innovative fabrication method for metal and ceramic-matrix composites. The study presents an in situ observation setup for capillary infiltration of molten silicon and reveals the two-step mechanism involved in the process.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Coupling tomographic and thermographic measurements for in-situ thermo-mechanical tests

Leonard Turpin et al.

Summary: This paper presents an experimental method and full-field measurement procedure for determining the thermo-mechanical properties of complex 3D woven ceramic composite materials, capturing 3D tomographic images of the sample at different loading stages and mapping the thermal field onto a 3D mesh using a pin-hole projective model. An integrated digital image correlation algorithm is proposed to calibrate the projection model, with a focus on the silhouette of the sample shape. The procedure is illustrated with an experimental case study.

MEASUREMENT SCIENCE AND TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Composites

Multiscale characterization and representation of variability in ceramic matrix composites

Khaled H. Khafagy et al.

Summary: This paper presents a detailed characterization study of structural and manufacturing flaws in Carbon fiber Silicon-Carbide-Nitride matrix (C/SiNC) CMCs at different length-scales, using various analytical methods. An image processing algorithm and a three-dimensional stochastic representative volume element (SRVE) generation algorithm were developed to accurately quantify architectural parameters variability and provide precise material texture representations at multiple length scales. The developed algorithm accurately accounts for material features and flaws based on a range of multiscale structural and defects characterization results.

JOURNAL OF COMPOSITE MATERIALS (2021)

添加到收藏夹

Article Mechanics

Optimal procedure for the identification of constitutive parameters from experimentally measured displacement fields

Stephane Roux et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

3D Detection and Quantitative Characterization of Cracks in a Ceramic Matrix Composite Tube Using X-Ray Computed Tomography

Y. Chen et al.

EXPERIMENTAL MECHANICS (2020)

添加到收藏夹

Article Materials Science, Ceramics

Creep behavior identification of an environmental barrier coating using full-field measurements

Thibaut Archer et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Linking microstructure and local mechanical properties in SiC-SiC fiber composite using micromechanical testing

Yevhen Zayachuk et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Mechanics

The correlation framework: Bridging the gap between modeling and analysis for 3D woven composites

Arturo Mendoza et al.

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Article Mechanics

Variational segmentation of textile composite preforms from X-ray computed tomography

Jean Benezech et al.

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Review Materials Science, Multidisciplinary

Digital Volume Correlation: Review of Progress and Challenges

A. Buljac et al.

EXPERIMENTAL MECHANICS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Damage investigation and modeling of 3D woven ceramic matrix composites from X-ray tomography in-situ tensile tests

Vincent Mazars et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Mechanics

An automated procedure for the generation and conformal discretization of 3D woven composites RVEs

Badadjida Wintiba et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Mechanics

Prediction of linear and non-linear behavior of 3D woven composite using mesoscopic voxel models reconstructed from X-ray micro-tomography

Yang Liu et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Engineering, Mechanical

Integrated digital image correlation applied to elastoplastic identification in a biaxial experiment

Morgan Bertin et al.

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2016)

添加到收藏夹

Article Mechanics

Internal geometric modelling of 3D woven composites: A comparison between different approaches

N. Isart et al.

COMPOSITE STRUCTURES (2015)

添加到收藏夹

Article Engineering, Multidisciplinary

General definition of 3D warp interlock fabric architecture

Francois Boussu et al.

COMPOSITES PART B-ENGINEERING (2015)

添加到收藏夹

Article Mechanics

Meso-scale FE analyses of textile composite reinforcement deformation based on X-ray computed tomography

N. Naouar et al.

COMPOSITE STRUCTURES (2014)

添加到收藏夹

Article Chemistry, Physical

Real-time quantitative imaging of failure events in materials under load at temperatures above 1,600 °C

Hrishikesh A. Bale et al.

NATURE MATERIALS (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of porosity on the elastic behaviour of CVI SiC/SiC composites

L. Gelebart et al.

JOURNAL OF NUCLEAR MATERIALS (2009)

添加到收藏夹

Article Engineering, Manufacturing

Three-dimensional image correlation from X-ray computed tomography of solid foam

Stephane Roux et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)

添加到收藏夹

Article Engineering, Multidisciplinary

Probabilistic analysis of a SiC/SiC ceramic matrix composite turbine vane

Pappu L. N. Murthy et al.

COMPOSITES PART B-ENGINEERING (2008)

添加到收藏夹

Article Engineering, Mechanical

Methods and applications of digital volume correlation

B. K. Bay

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2008)

添加到收藏夹

Review Materials Science, Composites

Meso-FE modelling of textile composites: Road map, data flow and algorithms

Stepan V. Lomov et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Stress intensity factor measurements from digital image correlation: post-processing and integrated approaches

Stephane Roux et al.

INTERNATIONAL JOURNAL OF FRACTURE (2006)

添加到收藏夹

Review Materials Science, Characterization & Testing

Digital image correlation: from displacement measurement to identification of elastic properties - a review

F Hild et al.

STRAIN (2006)

添加到收藏夹

Article Materials Science, Composites

Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: an overview

R Naslain

COMPOSITES SCIENCE AND TECHNOLOGY (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.