☆ 4.7 Article

Effect of calcium addition on the microstructure, mechanical properties, and corrosion behavior of AZ61-Nd alloy

ADVANCED COMPOSITES AND HYBRID MATERIALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Effect of Neodymium Modification on the Corrosion Behavior of AZ63 Magnesium Alloy

Jiarun Li et al.

Summary: The influence of Nd alloying on the microstructure and electrochemical behaviors of Mg-6 wt.% Al-3 wt.% Zn alloy was investigated. The results showed that appropriate Nd alloying can decrease the corrosion rate, but over alloying leads to accelerated corrosion.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2023)

添加到收藏夹

Article Chemistry, Physical

Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg-Zn-Gd-Y-Zr alloy

Ya Liu et al.

Summary: The effects of extrusion temperature and extrusion ratio on the microstructure, corrosion resistance, and mechanical properties of Mg-Zn-Gd-Y-Zr alloy were investigated. Higher extrusion temperatures and larger extrusion ratios were found to result in better mechanical properties and corrosion resistance.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of rare earth neodymium (Nd) and heat treatment on anti-corrosion behaviors of the AZ80 magnesium alloy

Minjie Liang et al.

Summary: The corrosion resistance of AZ80-xNd (x = 0, 0.5, and 1.0 wt.%) magnesium alloys is significantly affected by the rare earth neodymium (Nd) and heat treatment. The appropriate Nd content reduces the corrosion rate, but excessive Nd content decreases the corrosion resistance. The corrosion rate of solution treated alloys is higher than that of as-cast alloys, while the corrosion rate of aged alloys is the lowest. Rod-shaped Al3Nd phase and block-shaped Al2Nd phase effectively improve the corrosion resistance of the alloy.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

添加到收藏夹

Article

Microstructure and Mechanical Properties of Annealed Quinary Ni-Mn-Sn-Fe-In Heusler Alloy

Sandeep Nambiar S et al.

Engineered Science (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behavior of AZ31 magnesium alloy with calcium addition

Umer Masood Chaudry et al.

Summary: The effect of calcium on the microstructure and corrosion characteristics of AZ31 was investigated. It was found that the formation of (Mg, Al)(2)Ca in AZ31-0.5Ca contributed to improved corrosion resistance.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

AZ91 alloy nanocomposites reinforced with Mg-coated graphene: Phases distribution, interfacial microstructure, and property analysis

Zhanyong Zhao et al.

Summary: A new organic chemical reduction method was used to synthesize magnesium-coated graphene (GNPs) and fabricate nanocomposites with different contents. The microstructure of the composite was mainly composed of the matrix and the precipitated phase with different morphologies. With the increase of GNPs content, the grain and structure are refined, leading to improved hardness, reduced friction coefficient, and enhanced wear resistance.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Role of interfacial energy anisotropy in dendrite orientation in Al-Zn alloys: A phase field study

Yuhong Zhao et al.

Summary: The influence of interfacial energy anisotropy on dendrite morphology was investigated in Al-Zn alloys using the phase-field method. Different types of dendrite morphology were observed, and the occurrence of solute segregation holes and liquid grooves in dendrites was found to be influenced by the anisotropic interfacial energy. Supersaturation was found to be strongly correlated with the formation of liquid holes and liquid grooves as well as the degree of solute segregation. The relationship between interfacial energy anisotropy, Zn concentration, elastic anisotropy, and dendrite orientation deserves attention.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure, Mechanical Properties, and Corrosion Behavior of Mg-Al-Ca Alloy Prepared by Friction Stir Processing

Wen Wang et al.

Summary: Friction stir processing was used to improve the microstructure and mechanical properties of an Mg-Al-Ca alloy. The decrease in grain size, increase in strength, and decrease in corrosion rates were attributed to the modification. However, the stress corrosion cracking resistance decreased due to filiform corrosion induced by the Al8Mn5 phase.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

添加到收藏夹

Review Nanoscience & Nanotechnology

Waterborne polyurethane and its nanocomposites: a mini-review for anti-corrosion coating, flame retardancy, and biomedical applications

Jianchen Cai et al.

Summary: Waterborne polyurethanes (WPU) are environmentally friendly alternatives to solvent-borne polyurethanes. The properties of WPU can be tailored by choosing different monomers and monomer ratios. This mini-review discusses the synthesis of WPU, the influence of materials on their properties, and strategies to improve their performance. The structure-property relationship for their end-use applications is also emphasized.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

添加到收藏夹

Article Chemistry, Physical

Development of corrosion-resistant Mg-Al-Ca-Mn-Zn alloy sheet with good tensile properties and stretch formability

T. Nakata et al.

Summary: By investigating the effects of Al content on the mechanical properties, formability, and corrosion resistance of magnesium alloy sheets, it was found that moderate Al addition significantly improves these properties, resulting in good overall performance of the alloy sheets.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Anisotropy investigation of an ECAP-processed Mg-Al-Ca-Mn alloy with synergistically enhanced mechanical properties and corrosion resistance

Chao Sun et al.

Summary: This study investigated the anisotropy of a 32-pass ECAP processed Mg-3.7Al-1.8Ca-0.4Mn alloy, which exhibited synergistically enhanced mechanical properties and corrosion resistance. The ECAP alloy had homogeneous fine alpha-Mg grains and different distribution of refined Al2Ca particles. The refinement of microstructure resulted in the formation of a protective film on the ECAP alloy, leading to different corrosion mechanisms compared to the as-cast alloy. The distribution of Al2Ca and the texture of alpha-Mg were identified as the main factors affecting the anisotropic properties of the ECAP alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Simultaneously enhanced the strength and ductility in Mg17Al12 intermetallic compound with Ce addition

Baosheng Liu et al.

Summary: The novel Mg17Al12-3Ce alloy, fabricated by addition appropriate Ce, demonstrates significantly enhanced compressive properties compared to Mg17Al12 compound, primarily attributed to refined grains, reduced wetting grain boundaries, and precipitation of Al11Ce3 phase.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Chemistry, Applied

Waterborne acrylic resin co-modified by itaconic acid and γ-methacryloxypropyl triisopropoxidesilane for improved mechanical properties, thermal stability, and corrosion resistance

Zhuanghua Yu et al.

Summary: Waterborne acrylic resin modified with both IA and KH571 was successfully synthesized by seeded emulsion polymerization. The addition of IA and KH571 greatly improved the water resistance and other properties of the resin coating, making it a potential candidate for waterproof and anticorrosive coatings.

PROGRESS IN ORGANIC COATINGS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Phase transformations in an ultralight BCC Mg alloy during anisothermal ageing

Tongzheng Xin et al.

Summary: The phase transformation sequence, precipitation evolution, and optimized microstructure of Mg-Li-Al alloys were investigated. The main reason for alloy softening was analyzed, and the core-shell model of the phase transformation was observed and verified.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Mei-Xuan Li et al.

Summary: The effect of trace Ce addition on the microstructure evolution and corrosion behavior of dilute Mg-0.6Al-0.5Mn-0.25Ca alloys has been investigated. The addition of Ce resulted in the formation of less noble Al8Mn4Ce and Al11Ce3 phases. Notably, the alloy containing 0.3 wt% Ce exhibited the lowest corrosion rate, attributed to factors such as the low potential difference, compact composite oxide film, and enrichment of Fe.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Novel Mg-Al-Sn-Ca with enhanced mechanical properties and high corrosion rate via sub-rapid solidification for degradable magnesium alloy

Dawei Wang et al.

Summary: This study utilizes sub-rapid solidification (SRS) to modify the microstructure, particularly the eutectic phase, of Mg-4.5Al-1.5Sn-0.5Ca alloy. The SRS alloy exhibits superior strength-ductility synergy and increased corrosion rates compared to the conventional solidification alloy. This work proposes a novel degradable magnesium alloy and a processing method for its preparation.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Applied

Hydrothermally synthesized ZnO-RGO-PPy for water-borne epoxy nanocomposite coating with anticorrosive reinforcement

Qingsong Zhu et al.

Summary: Waterborne epoxy nanocomposite coating with hydrothermal synthesized zinc oxide-reduced graphene oxide-polypyrrole exhibited enhanced corrosion resistance and superior coating integrity. The synergistic protection mechanism of this coating includes barrier effects, chemical passivation, and electron acceptance.

PROGRESS IN ORGANIC COATINGS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Strengthening waterborne acrylic resin modified with trimethylolpropane triacrylate and compositing with carbon nanotubes for enhanced anticorrosion

Zhangyin Yan et al.

Summary: In this study, a two-component waterborne acrylic resin modified by TMPTA and KH792 was successfully prepared by solution polymerization. Resin composites were prepared using conductive carbon nanotubes (CNTs). The results showed that the modified resin film had enhanced mechanical properties, contact angle, and water resistance compared to the unmodified resin. Addition of CNTs also improved the corrosion resistance of the films.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

The influence of adding samarium on the microstructure, mechanical performance and corrosion behavior of as-extruded AZ41 alloys

Bao-sheng Liu et al.

Summary: The study found that adding an appropriate amount of Sm can inhibit the beta phase in AZ41 alloys, improve mechanical strength, and significantly enhance corrosion resistance. Among the different Sm content levels, the 2% Sm alloy showed the best tensile properties.

JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Ca addition on the microstructure and mechanical properties of heat-treated Mg-6.0Zn-1.2Y-0.7Zr alloy

Young-Gil Jung et al.

Summary: The addition of Ca improved the ignition resistance and refined the grains of the ZWK611 alloy, leading to enhanced mechanical properties at both room temperature and 150 degrees C. The presence of Tau- and W-phases, as well as the more uniform distribution of MgZn' precipitates in the Ca-added alloys, contributed to the improved performance of the T6-treated alloys.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

添加到收藏夹

Article Chemistry, Physical

The role of Ga in the microstructure, corrosion behavior and mechanical properties of as-extruded Mg-5Sn-xGa alloys

Xuejian Wang et al.

Summary: The addition of Ga element was found to enhance the corrosion resistance and tensile strength of Mg-5Sn alloy, with the maximum elongation to fracture achieved in Mg-5Sn-1Ga alloy. The precipitation of Mg5Ga2 particles and the formation of more stable corrosion products were observed with increasing Ga content in the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behavior of AZ91 Mg alloy with a heterogeneous structure produced by ECAP

Zhenquan Yang et al.

Summary: The microstructure of a commercial AZ91 Mg alloy was modified through ECAP and aging, resulting in improved corrosion resistance. Aging treatment at 150 degrees Celsius for 60-90 hours produced fine beta phase precipitates that enhanced the micro-galvanic effect, leading to increased corrosion rates still lower than that of the as-cast alloy.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Flexible and thermally stable superhydrophobic surface with excellent anti-corrosion behavior

Huibin Zhu et al.

JOURNAL OF MATERIALS SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure, Mechanical and Corrosion Properties of Mg-1.61Al-1.76Ca Alloy under Different Extrusion Temperatures

Zhuo Fu et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

添加到收藏夹

Article Chemistry, Physical

Effect of microalloyed Ca on the microstructure and corrosion behavior of extruded Mg alloy AZ31

Cheng Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Role of second phases on the corrosion resistance of Mg-Nd-Zr alloys

Jianyue Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhancing tensile strength of Mg-Al-Ca wrought alloys by increasing Ca concentration

Qiuyan Huang et al.

VACUUM (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Investigation of rapidly decomposable AZ91-RE-xCu (x=0, 1, 2, 3, 4) alloys for petroleum fracturing balls

Baosheng Liu et al.

JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Highly deformable Mg-Al-Ca alloy with Al2Ca precipitates

Gaoming Zhu et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced mechanical properties and corrosion resistance of a fine-grained Mg-9Al-1Zn alloy: the role of bimodal grain structure and β-Mg17Al12 precipitates

Yenny Cubides et al.

MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Structure, mechanical and corrosion properties of extruded Mg-Nd-Zn, Mg-Y-Zn and Mg-Y-Nd alloys

Drahomir Dvorsky et al.

MATERIALS SCIENCE AND TECHNOLOGY (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

On the role of Laves phases on the mechanical properties of Mg-Al-Ca alloys

M. Zubair et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effects of Ca Addition on the Mechanical Properties and Corrosion Behavior of ZM21 Wrought Alloys

Jiang Yang et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2017)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure and properties of hot extruded Mg-3Zn-Y-xCu (x=0, 1, 3, 5) alloys

Bao-sheng Liu et al.

INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of heat treatment on corrosion behavior of AZ63 magnesium alloy in 3.5 wt.% sodium chloride solution

Jiarun Li et al.

CORROSION SCIENCE (2016)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Degradation research of protective coating on AZ91D Mg alloy components via simulated contamination

Bao-sheng Liu et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2016)

添加到收藏夹

Article Chemistry, Physical

Influence of the Al2Ca phase on microstructure and mechanical properties of Mg-Al-Ca alloys

Zhongtao Jiang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical characterization and corrosion behavior of newly designed Sn and Y added AZ91 alloy

Arun Boby et al.

MATERIALS & DESIGN (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Nd on microstructure and mechanical properties of Mg-Al-Ca alloy

Y. Chen et al.

MATERIALS SCIENCE AND TECHNOLOGY (2014)

添加到收藏夹

Article Electrochemistry

Electrochemical impedance spectroscopy study of thermally grown oxides exhibiting constant phase element behaviour

L. Hamadou et al.

ELECTROCHIMICA ACTA (2013)

添加到收藏夹

Article Electrochemistry

Dielectric Properties of Materials Showing Constant-Phase-Element (CPE) Impedance Response

Mark E. Orazem et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of Zn concentration on the corrosion behavior of Mg-xZn alloys

Yingwei Song et al.

CORROSION SCIENCE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion of hot extrusion AZ91 magnesium alloy: I-relation between the microstructure and corrosion behavior

Tao Zhang et al.

CORROSION SCIENCE (2011)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.