☆ 4.6 Article

A study on ultrasonic welding of thermoplastics with significant differences in physical properties under different process parameters

MATERIALS TODAY COMMUNICATIONS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Multidisciplinary

Fusion Bonding Possibility for Incompatible Polymers by the Novel Ultrasonic Welding Technology: Effect of Interfacial Compatibilization

Xie Fu et al.

Summary: In this study, fusion bonding of incompatible polymers PP and PA6 was achieved by introducing an interlayer solder sheet (ISS) consisting of maleic anhydride-functionalized polypropylene (PP-g-MAH) and polyamide6 (PA6). The welding strength reached a high level, and the copolymer acted as an emulsifier to enhance the interfacial adhesion between PP and PA6.

ACS OMEGA (2022)

添加到收藏夹

Review Engineering, Manufacturing

Ultrasonic welding of fiber reinforced thermoplastic composites: Current understanding and challenges

Yaqiong Wang et al.

Summary: This paper presents the current understanding of the ultrasonic welding of fiber reinforced thermoplastic composites, focusing on weldability, welding quality, and underlying mechanisms in acoustic transmission, heat generation, and joint formation. Challenges in understanding this technique include special physical properties due to fibrous fillers, interphase interaction under ultrasonic energy, and melting and molecular inter-diffusion at the interface.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

添加到收藏夹

Article Biochemistry & Molecular Biology

Structural and Barrier Properties of Compatibilized PE/PA6 Multinanolayer Films

Quentin Lozay et al.

Summary: The study focused on the production of PE/PA6 multilayer films using multinanolayer coextrusion technique, which revealed changes in crystalline morphology and microstructure when the thickness of each polymer layer decreased to the nano-scale, impacting the gas and water transport properties. Despite the change in crystal orientation, a slight improvement in gas barrier properties was observed.

MEMBRANES (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Transformation plasticity of AF1410 steel and its influences on the welding residual stress and distortion: Experimental and numerical study

Kaiyuan Zhang et al.

Summary: This study investigated the influence of transformation plasticity on welding residual stress and distortion in AF1410 steel through experimental and numerical simulation methods. The results showed that transformation plasticity can reduce stress variation, but has little impact on distortion.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Engineering, Manufacturing

Friction stir spot welding of dissimilar ABS and PA6 by a tool with newly designed tooth-shaped flat pin

Yinfei Yan et al.

Summary: A specially designed flat-pin tool was used to friction stir spot weld ABS and PA6 plates, effectively enhancing the mechanical interlocking between the lapped sheets. The study also found that rotational speed significantly influences weld formation, PA6 morphology, and joint mechanical properties.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Engineering, Electrical & Electronic

Strategy of Fabricating Flexible Strain Sensor via Layer-by-Layer Assembly of Conductive Hydrogels

Yao Chen et al.

Summary: A flexible strain sensor with a hydrogels-conductive materials-hydrogels hierarchical sandwich structure was prepared using layer-by-layer assembly technology in this study. The introduction of MXene materials significantly improved the sensitivity of the sensor. The sensor could withstand various forms of deformation and stress, showing potential applications in human-activity monitoring.

ACS APPLIED ELECTRONIC MATERIALS (2021)

添加到收藏夹

Article Materials Science, Composites

On the sensitivity of the ultrasonic welding process of epoxy- to polyetheretherketone (PEEK)-based composites to the welding force and amplitude of vibrations

Eirini Tsiangou et al.

Summary: This paper investigates the sensitivity of the ultrasonic welding process for joining dissimilar composites to variations in welding force or vibration amplitude, finding that reducing either parameter increases heating time and maximum temperatures. Despite local signs of thermal degradation, these alterations do not significantly affect the maximum lap shear strength of the welded joints.

COMPOSITES PART C: OPEN ACCESS (2021)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Ultrasonic welding of GF/PA6T composites: Experimental investigation and process optimization

R. Kalyan Kumar et al.

Summary: This paper presents an optimization study on joining glass filled high-performance polyamide parts by ultrasonic welding, with a confirmation of experimental results matching the fitted statistical model.

MATERIALS TODAY-PROCEEDINGS (2021)

添加到收藏夹

Article Materials Science, Composites

Continuous ultrasonic welding of thermoplastic composites: Enhancing the weld uniformity by changing the energy director

Bram Jongbloed et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

Carbon nanotube-geopolymer nanocomposites: A molecular dynamics study of the influence of interfacial chemical bonding upon the structural and mechanical properties

M. F. Kai et al.

CARBON (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigations on the mechanism of microweld changes during ultrasonic wire bonding by molecular dynamics simulation

Yangyang Long et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Nondestructive Strategy to Effectively Enhance the Interfacial Adhesion of PBO/Epoxy Composites

Shaohua Wu et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

添加到收藏夹

Article Polymer Science

Effect of Flow-Induced Molecular Alignment on Welding and Strength of Polymer Interfaces

Marco A. G. Cunha et al.

MACROMOLECULES (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Online quality inspection of ultrasonic composite welding by combining artificial intelligence technologies with welding process signatures

Yang Li et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

On differences and similarities between static and continuous ultrasonic welding of thermoplastic composites

Bram Jongbloed et al.

COMPOSITES PART B-ENGINEERING (2020)

添加到收藏夹

Article Polymer Science

Welding dynamics in an atomistic model of an amorphous polymer blend with polymer-polymer interface

Dmitry G. Luchinsky et al.

JOURNAL OF POLYMER SCIENCE (2020)

添加到收藏夹

Article Polymer Science

Nanorheology with a Conventional Rheometer: Probing the Interfacial Properties in Compatibilized Multinanolayer Polymer Films

Quentin Beuguel et al.

ACS MACRO LETTERS (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Experimental and numerical procedure for studying strength and heat generation responses of ultrasonic welding of polymer blends

M. Natesh et al.

MEASUREMENT (2019)

添加到收藏夹

Article Chemistry, Physical

Experimental Studies on Thermo-Mechanical Behavior of Ultrasonically Welded PC/ABS Polymer Blends

T. Chinnadurai et al.

SILICON (2018)

添加到收藏夹

Article Mechanics

Numerical analysis and experimental observation of ultrasonic wave propagation in CFRP with curved fibers

Takeshi Ashizawa et al.

COMPOSITE STRUCTURES (2018)

添加到收藏夹

Article Engineering, Manufacturing

Towards robust sequential ultrasonic spot welding of thermoplastic composites: Welding process control strategy for consistent weld quality

Tian Zhao et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

添加到收藏夹

Article Engineering, Manufacturing

Laser conduction welding characteristics of dissimilar metals Mg/Ti with Al interlayer

Chengwei Zang et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

添加到收藏夹

Article Engineering, Manufacturing

The study of laser transmission joining PA66 and PVC with large compatibility difference

Huixia Liu et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

添加到收藏夹

Article Materials Science, Composites

On the effect of flat energy directors thickness on heat generation during ultrasonic welding of thermoplastic composites

Genevieve Palardy et al.

COMPOSITE INTERFACES (2016)

添加到收藏夹

Article Polymer Science

A Reptation Model of Slip at Entangled Polymer-Polymer Interfaces

Andrew Gustafson et al.

MACROMOLECULES (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of ultrasonic assisted underwater wet welding joints

Q. J. Sun et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Engineering, Manufacturing

On avoiding thermal degradation during welding of high-performance thermoplastic composites to thermoset composites

Irene Fernandez Villegas et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)

添加到收藏夹

Article Engineering, Manufacturing

Strength development versus process data in ultrasonic welding of thermoplastic composites with flat energy directors and its application to the definition of optimum processing parameters

Irene Fernandez Villegas

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2014)

添加到收藏夹

Article Polymer Science

Structure and Strength at Immiscible Polymer Interfaces

Ting Ge et al.

ACS MACRO LETTERS (2013)

添加到收藏夹

Article Materials Science, Composites

Study on Heating Process of Ultrasonic Welding for Thermoplastics

Zongbo Zhang et al.

JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2010)

添加到收藏夹

Review Engineering, Manufacturing

Advances in fusion bonding techniques for joining thermoplastic matrix composites: a review

C Ageorges et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.