相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。The precipitation behaviours and strengthening mechanism of a Cu-0.4 wt% Sc alloy
Zifan Hao et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)
Microstructure tailoring of Al0.5CoCrFeMnNi to achieve high strength and high uniform strain using severe plastic deformation and an annealing treatment
H. T. Jeong et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)
Evolution of dislocation and stacking-fault densities for a Cu-0.7Cr-0.07Zr alloy during cryogenic tensile test: An in-situ synchrotron X-ray diffraction analysis
P. H. F. Oliveira et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
Contrasting roles of Laves_Cr2Nb precipitates on the creep properties of novel CuCrNbZr alloys
Ling Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Contribution of Zr to strength and grain refinement in Cu-Cr-Zr alloy
Jinshui Chen et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Texture evolution and strengthening mechanism of single crystal copper during ECAP
Tingbiao Guo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Effect of chromium and zirconium content on structure, strength and electrical conductivity of Cu-Cr-Zr alloys after high pressure torsion
D. V. Shangina et al.
MATERIALS LETTERS (2017)
Phase transformation behaviors and properties of a high strength Cu-Ni-Si alloy
Qian Lei et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Microstructure and properties of powder metallurgy Cu-1%Cr-0.65%Zr alloy prepared by hot pressing
Jiamin Zhou et al.
VACUUM (2016)
Deformation microstructures, strengthening mechanisms, and electrical conductivity in a Cu-Cr-Zr alloy
R. Mishnev et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
A high strength and high electrical conductivity bulk CuCrZr alloy with nanotwins
L. X. Sun et al.
SCRIPTA MATERIALIA (2015)
Precipitation Behavior of Cu-1.9Be-0.3Ni-0.15Co Alloy During Aging
Yan-Chuan Tang et al.
ACTA METALLURGICA SINICA-ENGLISH LETTERS (2015)
Varying tensile fracture mechanisms of Cu and Cu-Zn alloys with reduced grain size: From necking to shearing instability
P. Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Ultrafine grains and the Hall-Petch relationship in an Al-Mg-Si alloy processed by high-pressure torsion
Aicha Loucif et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Nanostructuring Nb by various techniques of severe plastic deformation
V. V. Popov et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Strengthening Materials by Engineering Coherent Internal Boundaries at the Nanoscale
K. Lu et al.
SCIENCE (2009)
Enhanced fracture toughness of bulk nanocrystalline Cu with embedded nanoscale twins
E. W. Qin et al.
SCRIPTA MATERIALIA (2009)
Influence of Zr addition on the microstructure evolution and thermal stability of Al-Mg-Mn alloy processed by ECAP at elevated temperature
Jiang Li Ning et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)
Nanocrystalline Al-Mg alloy with ultrahigh strength and good ductility
KM Youssef et al.
SCRIPTA MATERIALIA (2006)
Hall-Petch relation and boundary strengthening
N Hansen
SCRIPTA MATERIALIA (2004)
Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing
YH Zhao et al.
ACTA MATERIALIA (2004)
分享论文
