☆ 4.6 Article

Effect of Hot Isostatic Pressing Process Parameters on Properties and Fracture Behavior of Tungsten Alloy Powders and Sintered Bars

MATERIALS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Microstructural and mechanical characterisation of WC-Co alloys elaborated by liquid phase sintering and hot isostatic pressing: study of WC crystallites size evolution

Hassiba Rabouhi et al.

Summary: This study aims to investigate the microstructure and WC crystallite size evolution of WC-Co alloys produced by liquid phase sintering and hot isostatic pressing (HIP). The results show a clear improvement in micro-hardness for materials densified by HIP.

CANADIAN METALLURGICAL QUARTERLY (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of tantalum addition method on microstructure and mechanical properties of the 90(W-20Ta)-Ni-Fe alloy

Yong Zhang et al.

Summary: The method of adding initial elements significantly affects the structure and mechanical properties of tungsten alloy. In this study, the 90(W-20Ta)-Ni-Fe alloy was prepared using direct addition of elements and W-Ta pre-alloying. The diffusion of elements and phase transformation behavior under different conditions were discussed. It was found that direct addition of tantalum led to the deterioration of alloy structure, while W-Ta pre-alloying improved both the uniformity and strength of the alloy.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Densification behavior of tungsten alloy powders during hot isostatic pressing

Biao Hu et al.

Summary: The Shima yielding criterion was used to simulate the densification behavior of 93 W-Ni-Fe alloy during HIP process. The densification process of tungsten alloy powders was found to consist of expansion, shrinking, and uniform densification stages. The relative density increased by 2.3% with a temperature increase of 100 degrees Celsius.

MATERIALS TODAY COMMUNICATIONS (2022)

添加到收藏夹

Article Chemistry, Physical

Densification and microstructure formation mechanisms of 80 W-14Ni6Fe fabricated by laser powder bed fusion

Han Ye et al.

Summary: Laser additive manufacturing (LAM) provides a feasible route for machining complex tungsten alloy parts. In this study, high-density and defect-free tungsten alloy specimens were obtained using laser powder bed fusion (LPBF). The microstructure and strengthening mechanisms of the LPBFed tungsten alloy were investigated, and the alloy exhibited high tensile strength.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Review Chemistry, Physical

Effect of Rare Earth Metals (Y, La) and Refractory Metals (Mo, Ta, Re) to Improve the Mechanical Properties of W-Ni-Fe Alloy-A Review

Senthilnathan Natarajan et al.

Summary: Tungsten heavy alloys have improved mechanical properties and achieved good tensile and compressive strengths at high temperatures through doping with other elements.

MATERIALS (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Influence of hot isostatic pressing on microstructure, properties and deformability of selective laser melting TC4 alloy

Tai-qi Yan et al.

Summary: The study investigated the effect of different hot isostatic pressing regimes on the properties of TC4 alloy fabricated by selective laser melting technology. Results showed that the phase constitution and microstructure of the alloy changed after hot isostatic pressing, leading to a decrease in strength and hardness but an increase in ductility. The optimal hot isostatic pressing regime was found to be 940 degrees C/3 h/150 MPa, achieving a tensile strength of approximately 890 MPa and an elongation of around 14.0%.

CHINA FOUNDRY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Consolidation and properties of tungsten by spark plasma sintering and hot isostatic pressing

Jong Min Byun et al.

Summary: The study attempted to fabricate dense tungsten using a combination process of spark plasma sintering and hot isostatic pressing, achieving an improvement in relative density and higher strength. X-ray diffractometry and X-ray photoelectron spectroscopy analysis revealed that the specimens were mainly composed of tungsten with trace amounts of metallic tungsten bound with oxygen. The strength testing showed promising results with biaxial bending test.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fine tungsten precipitates in the matrix phase and their influence on the mechanical properties of a tungsten heavy alloy

G. Prabhu et al.

Summary: Post-sintering cyclic heat treatment of W-Ni-Co alloys leads to the formation of fine tungsten precipitates in the matrix, with the volume fraction of precipitates increasing with the number of heat treatment cycles. This study investigates the influence of increasing precipitate fraction on the mechanical properties of 92W-5Ni-3Co alloy through varying the number of heat treatment cycles and cooling rates to prevent the re-formation of brittle intermetallic phase. The potential of W-Ni-Co alloys with fine precipitates in enhancing mechanical properties, especially in critical applications like kinetic energy penetrators, is highlighted for further improvement through thermomechanical treatments.

PHILOSOPHICAL MAGAZINE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of hot isostatic pressing on thermal conductivity of additively manufactured pure tungsten

Jinhan Chen et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

Fabrication of ultrafine-grain and great-performance W-Ni-Fe alloy with medium W content

Lei Ye et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of W-ZrO2 alloys by different preparation techniques

Fangnao Xiao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Nuclear Science & Technology

Mechanical properties and microstructure of W/CuY and W/CuCrZr composites produced by hot isostatic pressing

M. Eddahbi et al.

FUSION ENGINEERING AND DESIGN (2019)

添加到收藏夹

Article Nuclear Science & Technology

Influence of the fabrication route of tunsgen-2 wt.% vanadium in the microstructure and mechanical properties

T. Palacios et al.

FUSION ENGINEERING AND DESIGN (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation of electrochemical micromachining of tungsten microtools

Xinxin Qi et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2018)

添加到收藏夹

Review Metallurgy & Metallurgical Engineering

Sintering of Tungsten and Tungsten Heavy Alloys of W-Ni-Fe and W-Ni-Cu: A Review

N. Senthilnathan et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural and mechanical characteristics of W-2Ti and W-1TiC processed by hot isostatic pressing

A. Munoz et al.

JOURNAL OF NUCLEAR MATERIALS (2014)

添加到收藏夹

Article Materials Science, Ceramics

Binderless sub-micron WC consolidated by hot pressing and treated by hot isostatic pressing

Yong Wang et al.

JOURNAL OF THE CERAMIC SOCIETY OF JAPAN (2014)

添加到收藏夹

Article Nuclear Science & Technology

Bonding tungsten, W-Cu-alloy and copper with amorphous Fe-W alloy transition

Song Wang et al.

FUSION ENGINEERING AND DESIGN (2013)

添加到收藏夹

Article Nuclear Science & Technology

Development of oxide dispersion strengthened W alloys produced by hot isostatic pressing

J. Martinez et al.

FUSION ENGINEERING AND DESIGN (2011)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.