☆ 4.5 Article

Analysis of Drilling Behaviour in Jute Fibres Reinforced Natural Composites

JOURNAL OF NATURAL FIBERS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Review Materials Science, Textiles

Drilling Performance of Natural Fiber Reinforced Polymer Composites: A Review

Khurshid Malik et al.

Summary: This paper reviews the past and present research studies of the drilling behavior of NFRCs and their hybrids, exploring various drilling techniques and parameters, as well as analyzing drill bit geometry and materials. The study highlights methods of improving drilling properties for these composites, including chemical treatment of natural fibers and optimizing drilling performance parameters.

JOURNAL OF NATURAL FIBERS (2022)

添加到收藏夹

Article Materials Science, Composites

Drilling of natural fiber-reinforced based polyurethane foam composite

Alessandro Ellenberger et al.

Summary: The combination of natural fibers and renewable source matrices can replace non-renewable materials in composites manufacturing. This study investigates the drilling process and its impact on surface damages and temperature in composites made of pinus sawdust and sisal fibers with a polyurethane foam derived from vegetable oils matrix. The results show that drilling parameters have an influence on the generation of damages, and lower cutting speed and feed rate are more suitable for drilling these types of composites.

JOURNAL OF COMPOSITE MATERIALS (2022)

添加到收藏夹

Article Materials Science, Composites

Image processing method for delamination and fiber pull-out assessment during drilling of natural fiber composites

Muhammad Helmi Abdul Kudus et al.

Summary: Natural fiber-reinforced composites are promising alternative materials for modern moderate-to-high-technology products, but their heterogeneous structure can cause processing defects. Drilling of composites is essential for assembly, but can lead to delamination damage and fiber pull-out. A new image processing method has been developed to characterize these defects and investigate the effects of drilling parameters on them.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2022)

添加到收藏夹

Article Engineering, Manufacturing

Effects of machining parameters on surface quality of composites reinforced with natural fibers

Raveen John et al.

Summary: This study analyzed the effects of machining parameters on the surface quality of natural fiber reinforced composites during end milling, finding significant differences in silicon content and hardness values of different fibers impacting the surface quality. Kenaf/PP composites showed the lowest delamination damages and best surface finish, while RH/PP composites were the most challenging to machine. Spindle speed was found to have a greater influence on machined surface quality compared to feed rate for NFRCs.

MATERIALS AND MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Materials Science, Composites

Predicting the delamination factor in carbon fibre reinforced plastic composites during drilling through the Gaussian process regression

Yun Zhang et al.

Summary: CFRP is widely used in aircraft structural applications due to its superior properties, but drilling-induced delamination is a major concern. In this study, a GPR model is developed to predict delaminations in CFRP composites during drilling, which, combined with the Taguchi method, can provide faster optimization of machining processes with more quantitative data extracted from fewer experimental trials.

JOURNAL OF COMPOSITE MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation of Drilling Process Parameters of Palmyra Based Composite

A. Mohan Kumar et al.

Summary: The drilling process is crucial in the final assembly of mechanical parts. This study aimed to determine the minimum thrust force produced by the drill tool at specified drilling process parameters. The results showed that the candlestick drill bit generated the least thrust force at the specified drilling process parameters, followed by the twist and step cone drill bits.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2021)

添加到收藏夹

Article

Comparative Analysis of Drilling Behaviour of Synthetic and Natural Fiber-Based Composites

A. Mohan Kumar et al.

Advances in Materials Science and Engineering (2021)

添加到收藏夹

Article Automation & Control Systems

Mechanical characterization and optimization of delamination factor in drilling bidirectional jute fibre-reinforced polymer biocomposites

Ahmed Belaadi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Study the Impact of Drilling Process Parameters on Natural Fiber Reinforced Herringbone Epoxy Composites

Nagamadhu Mahadevappa et al.

ANNALES DE CHIMIE-SCIENCE DES MATERIAUX (2020)

添加到收藏夹

Article Materials Science, Composites

An experimental study on milling of natural fiber (jute)- reinforced polymer composites

Yahya H. Celik et al.

JOURNAL OF COMPOSITE MATERIALS (2019)

添加到收藏夹

Article Engineering, Manufacturing

Experimental investigation on drilling of natural flax fiber-reinforced composites

H. Rezghi Maleki et al.

MATERIALS AND MANUFACTURING PROCESSES (2019)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Study on Drilling of Woven Sisal and Aloevera Natural Fibre Polymer Composite

A. Shadrach Jeya Sekaran et al.

MATERIALS TODAY-PROCEEDINGS (2019)

添加到收藏夹

Article Materials Science, Composites

The challenges of natural fiber in manufacturing, material selection, and technology application: A review

Tabrej Khan et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2018)

添加到收藏夹

Review Mechanics

Recent advances in drilling hybrid FRP/Ti composite: A state-of-the-art review

Jinyang Xu et al.

COMPOSITE STRUCTURES (2016)

添加到收藏夹

Article Engineering, Multidisciplinary

Comprehensive study on machinability of sustainable and conventional fibre reinforced polymer composites

Sikiru Oluwarotimi Ismail et al.

ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2016)

添加到收藏夹

Article Automation & Control Systems

Regression modeling and optimization of machinability behavior of glass-coir-polyester hybrid composite using factorial design methodology

S. Jayabal et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)

添加到收藏夹

Article Automation & Control Systems

Thrust force and delamination of core-saw drill during drilling of carbon fiber reinforced plastics (CFRP)

C. C. Tsao

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2008)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.