☆ 4.7 Article

Impact of HVOF sprayed Vanadium Carbide (VC) based novel coatings on slurry erosion behaviour of hydro-machinery SS316 steel

TRIBOLOGY INTERNATIONAL (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Coatings & Films

Cavitation erosion behavior of high velocity oxy fuel (HVOF) sprayed (VC plus CuNi-Cr) based novel coatings on SS316 steel

Vikrant Singh et al.

Summary: In this study, a mixture of VC and CuNi-Cr was successfully used to enhance the cavitation erosion resistance of SS316 steel. The increase in VC content in the coatings resulted in higher hardness, porosity, and thickness, and changed the failure mode of the coatings from ductile to brittle.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of laser cladding parameters on slurry erosion performance of NiCrSiBC+50WC claddings

Sarpreet Singh et al.

Summary: Laser cladding was used to deposit hard layers of NiCrSiBC + 50WC powder on SS410 steel. The laser cladding parameters significantly influenced the micro-hardness of the coatings, while the powder feed rate had a minimal effect. The NiCrSiBC + 50WC clad surfaces exhibited enhanced slurry erosion resistance due to their higher hardness. The main wear mechanisms observed in the slurry eroded clads were plastic deformation, micro-cutting, crater formation, and ploughing. A combination of high scanning speed, high laser beam power, and intermediate powder feed rate was found to be suitable for developing coatings with superior wear resistance.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

添加到收藏夹

Article Materials Science, Ceramics

Cavitation erosion characteristics at various flow velocities in NaCl medium of carbide-based cermet coatings prepared by HVOF spraying

Sheng Hong et al.

Summary: The study found that WCN coating exhibited higher hardness and elastic modulus, lower volume loss rate, and enhanced CE resistance compared to CN coating in NaCl medium. Increasing flow velocity led to higher volume loss rates for both coatings.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of fuel pressure, feed rate, and spray distance on cavitation erosion of Rodojet sprayed Al2O3+50%TiO2 coated AISI410 steel

Shivam Pandey et al.

Summary: Research on cavitation erosion of hydro-machinery revealed the importance of protective coatings with Al2O3 and TiO2 materials, where the coating parameters play a crucial role in resisting cavitation damage. Comparing the cavitation erosion of bare AISI410 steel with coated surfaces, it was found that the coatings provide higher resistance to cavitation erosion.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Erosion behavior of laser cladded Colmonoy-6+50%WC on SS410 steel under accelerated slurry erosion testing

Sarpreet Singh et al.

Summary: Research on laser cladding Colmonoy-6 + 50% WC powder on SS410 steel surfaces significantly improved the wear erosion resistance of the material. Impact velocity was found to be the major contributor to slurry erosion, followed by impact angle, average particle size, and slurry concentration.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

添加到收藏夹

Review Engineering, Manufacturing

Recent advancements in nano-lubrication strategies for machining processes considering their health and environmental impacts

Kishan Zadafiya et al.

Summary: This paper discusses the impact of using nanofluid as a cutting fluid on machining processes, emphasizing the importance of nano lubrication systems in improving the heat transfer characteristics of base fluids.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Engineering, Mechanical

Erosion tribo-performance of HVOF deposited Stellite-6 and Colmonoy-88 micron layers on SS-316L

Jashanpreet Singh et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Xiao-bin Liu et al.

SURFACE ENGINEERING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wear, erosion and corrosion resistance of HVOF-sprayed WC and Cr3C2 based coatings for electrolytic hard chrome replacement

Qun Wang et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Microwave-Assisted Post-processing of Detonation Gun-Sprayed Coatings for Better Slurry and Cavitation Erosion Resistance

Abhishek Babu et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Slurry Erosion Behavior of HVOF-Sprayed WC-10Co-4Cr Coated SS 316 Steel with and Without PTFE Modification

Anuj Bansal et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2019)

添加到收藏夹

Review Engineering, Multidisciplinary

Micro and nano ceramic-metal composite coatings by thermal spray process to control slurry erosion in hydroturbine steel: an overview

Vibhu Sharma et al.

ENGINEERING RESEARCH EXPRESS (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Performance Analysis of CA6NM Hydro-Turbine Steel Under Accelerated Conditions by Using an Indigenously Developed Slurry Erosion Tester

Rajeev Kumar et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2018)

添加到收藏夹

Article Thermodynamics

A methodology for assessment of erosive wear on a Francis turbine runner

Junaid H. Masoodi et al.

ENERGY (2017)

添加到收藏夹

Article Chemistry, Physical

Erosion and corrosion resistance of laser cladded AISI 420 stainless steel reinforced with VC

Zhe Zhang et al.

APPLIED SURFACE SCIENCE (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Design and Development of High-Velocity Slurry Erosion Test Rig Using CFD

H. S. Grewal et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2013)

添加到收藏夹

Article Engineering, Manufacturing

Interrupted machining analysis for Ti6Al4V and Ti5553 titanium alloys using physical vapor deposition (PVD)-coated carbide inserts

Navneet Khanna et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2013)

添加到收藏夹

Article Engineering, Mechanical

Slurry erosion behaviour of HVOF sprayed WC-10Co-4Cr and Al2O3+13TiO2 coatings on a turbine steel

Deepak Kumar Goyal et al.

WEAR (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Study on mechanical and erosion wear behavior of hybrid composites using Taguchi experimental design

S. S. Mahapatra et al.

MATERIALS & DESIGN (2009)

添加到收藏夹

Article Mechanics

Mechanics of submerged jet cavitating action: material properties, exposure time and temperature effects on erosion

Ezddin Ali Farag Hutli et al.

ARCHIVE OF APPLIED MECHANICS (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Slurry erosion studies on surface modified 13Cr-4Ni steels: Effect of angle of impingement and particle size

T. Manisekaran et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2007)

添加到收藏夹

Article Engineering, Mechanical

Slurry erosion of thermal spray coatings and stainless steels for hydraulic machinery

J. F. Santa et al.

WEAR (2007)

添加到收藏夹

Article Engineering, Mechanical

Slurry wear and cavitation erosion of thermal-sprayed cermets

K Sugiyama et al.

WEAR (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Structure and wear behaviour of HVOF sprayed Cr3C2-NiCr and WC-Co coatings

T Sahraoui et al.

MATERIALS & DESIGN (2003)

添加到收藏夹

Article Engineering, Industrial

Laser cladding of aerospace materials

L Sexton et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.