☆ 4.6 Article

Effects of recast layer on fatigue performance of laser-drilled holes in nickel-based superalloy

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Shielding effects on fatigue and crack growth of the recasting zone induced by laser manufacturing in a nickel-based superalloy

Tinglian Zhang et al.

Summary: The present study investigated the fatigue properties and crack growth of laser recasting materials using experimental and computational methods. The shielding effect observed is attributed to strength mismatch, leading to cyclic softening and mean stress relaxation in the under-matched recasting material. The recasting material exhibits higher crack nucleation resistance and lower crack growth rate compared to the base material, indicating that the weak recasting zone does not significantly impact the overall mechanical performance of the structure.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of heat treatments on microstructure and mechanical properties of laser melting multi-layer materials

Tinglian Zhang et al.

Summary: The effects of different heat treatments on the microstructure and mechanical properties of laser melting nickel-based superalloys were systematically investigated in this study. The strength improvement of the heat-treated material was mainly derived from aging treatment and direct aging treatment, and it is recommended to use direct aging treatment for strengthening laser melting materials.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Optics

A process modeling approach for micro drilling of aerospace alloys with a waterjet guided laser system

Levent Subasi et al.

Summary: Laser drilling is an effective method for creating cooling holes on gas turbine parts. Waterjet guided laser (WJGL) is a hybrid process that offers improved machining results by coupling a laser beam with a thin cylindrical waterjet. It has potential for micro drilling operations on aerospace jet engine parts. However, further research is needed to understand the effects of process variables on material removal rate.

OPTICS AND LASER TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Industrial

Additive manufacturing of functionally graded inconel 718: Effect of heat treatment and building orientation on microstructure and fatigue behaviour

Saeede Ghorbanpour et al.

Summary: This paper investigates the effect of post-process heat treatments on the microstructure and fatigue crack growth behavior of functionally graded (FG) laser powder bed fusion (L-PBF) Inconel 718 (IN718) superalloy. The study shows that heat treatments can enhance the damage tolerance of L-PBF IN718 to the level of wrought material. Additionally, the effect of roughness-induced crack closure is found to be dependent on the build orientation.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Optics

Experimental study of nickel-based superalloy IN792 with femtosecond laser drilling method

Fengyun Zhang et al.

Summary: The study investigates a two-step approach for femtosecond laser drilling of nickel-based superalloys, proposing corresponding drilling optimization strategies based on different processing path parameters. Experimental results demonstrate the significant improvement in hole quality achieved with the two-step method compared to the one-step method.

OPTICS AND LASER TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Experimental and analytical investigation on service life of film cooling structure for single crystal turbine blade

Zixu Guo et al.

Summary: This study conducted life tests and analysis on the film cooling structure of single crystal turbine blade to predict service lives and understand damage mechanisms. The strain distribution was measured using digital image correlation, and a model based on the theory of critical distance was improved for life prediction. The crack nucleation mechanism was discussed, finding that microcracks around hole edges were induced by persistent slip bands. Microscopic observation revealed the uneven spatial distributions of matrix channel width and dislocation density, which can be used for life prediction and fault diagnosis of film cooling structures under service conditions.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

添加到收藏夹

Article Mechanics

Evaluation of different drilling quality and fatigue life prediction of nickel-based superalloy using equivalent initial flaw size

Fei Li et al.

Summary: This study evaluates the initial quality and fatigue life of nickel-based superalloys under different drilling processes, proposing a new expression for fatigue crack growth rate and predicting total fatigue life within 2 times error band. The validity of fatigue models and tests is confirmed through the combination of Equivalent Initial Flaw Size (EIFS) and fatigue crack growth rate.

ENGINEERING FRACTURE MECHANICS (2021)

添加到收藏夹

Article Engineering, Industrial

Microstructural characterization and fatigue performance of the recast material induced by laser manufacturing of a nickel-based superalloy

Tinglian Zhang et al.

Summary: The research systematically investigated the microstructures and mechanical properties of laser-induced recast material on nickel-based superalloy Inconel 718, finding that the yield strength and microhardness in the recast zone are lower than that of the base material due to epitaxial growth of columnar grains and a decrease in strengthening phases gamma' and gamma''. On the other hand, the recast-affected zone shows higher yield strength attributed to the growth of strengthening twins, partial dissolution of the delta phase, and cold work hardening.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of different drilling techniques on high-cycle fatigue behavior of nickel-based single-crystal superalloy with film cooling hole

Zhijin Zhang et al.

Summary: The study found that different drilling techniques have a significant impact on the high-cycle fatigue life of the nickel-based single-crystal superalloy, and the fatigue limit of the EDM specimens varies at different temperatures. The destruction of the specimens exhibits a typical multisource rupture morphology.

HIGH TEMPERATURE MATERIALS AND PROCESSES (2021)

添加到收藏夹

Article Engineering, Industrial

Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion

Chuan Guo et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Mechanical

Cyclic plasticity modeling of nickel-based superalloy Inconel 718 under multi-axial thermo-mechanical fatigue loading conditions

Jingyu Sun et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Engineering, Industrial

Investigation of process factors affecting mechanical properties of INCONEL 718 superalloy in wire plus arc additive manufacture process

Xiangfang Xu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

添加到收藏夹

Article Chemistry, Physical

Effects of dielectric fluids on surface integrity for the recast layer in high speed EDM drilling of nickel alloy

Chaojiang Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Engineering, Mechanical

Temperature dependence of strengthening mechanisms in a twinning-induced plasticity steel

Z. Y. Liang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2019)

添加到收藏夹

Article Automation & Control Systems

Investigation of recast and crack formation in laser trepanning drilling of CMSX-4 angled holes

Nicolau Iralal Morar et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

添加到收藏夹

Review Optics

Pulsed Nd:YAG laser beam drilling: A review

Girish Dutt Gautam et al.

OPTICS AND LASER TECHNOLOGY (2018)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Effect of recast layer on the low cycle fatigue life of electric discharge machined inconel 718

M. Anthony Xavior et al.

MATERIALS TODAY-PROCEEDINGS (2018)

添加到收藏夹

Article Engineering, Mechanical

The effect of trepanning speed of laser drilled acute angled cooling holes on the high temperature low cycle corrosion fatigue performance of CMSX-4 at 850 °C

N. Morar et al.

INTERNATIONAL JOURNAL OF FATIGUE (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

The influence of Laves phases on the high-cycle fatigue behavior of laser additive manufactured Inconel 718

Shang Sui et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Engineering, Mechanical

Experimental investigation on low cycle fatigue of DZ125 with film cooling holes in different processes of laser drilling

Jianwei Liang et al.

ENGINEERING FAILURE ANALYSIS (2016)

添加到收藏夹

Article Automation & Control Systems

Effect of temporally modulated pulse on reducing recast layer in laser drilling

Wenqiang Duan et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

添加到收藏夹

Article Engineering, Mechanical

Thermomechanical fatigue crack growth from laser drilled holes in single crystal nickel based superalloy

R. K. Kersey et al.

INTERNATIONAL JOURNAL OF FATIGUE (2013)

添加到收藏夹

Review Multidisciplinary Sciences

Strengthening Materials by Engineering Coherent Internal Boundaries at the Nanoscale

K. Lu et al.

SCIENCE (2009)

添加到收藏夹

Article Nanoscience & Nanotechnology

Nanoscale carbide precipitation in the recast layer of a percussion laser-drilled superalloy

Jacquelynn K. M. Garofano et al.

SCRIPTA MATERIALIA (2009)

添加到收藏夹

Article Engineering, Mechanical

Numerical integration method for kinematic hardening rules with partial activation of dynamic recovery term

M Abdel-Karim

INTERNATIONAL JOURNAL OF PLASTICITY (2005)

添加到收藏夹

Article Nanoscience & Nanotechnology

Misorientation development in grains of tensile strained and crept 2.25%Cr-1%Mo steel

C Fukuoka et al.

SCRIPTA MATERIALIA (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.