☆ 4.5 Article

Local-distortional interaction behaviour and design of cold-formed steel built-up columns

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Civil

Design of locally buckling cold-formed steel built-up columns formed unlipped channel sections

Akshay Mangal Mahar et al.

Summary: This study proposes a design procedure for predicting the local buckling strength of cold-formed steel built-up I and box section columns. The procedure combines the Effective Width Method and the Direct Strength Method. Finite element analysis and compression tests were performed to validate the models used in the study. The results show that the local buckling strength of built-up I sections is equal to the sum of its section' strength, whereas for box sections, the strength can be higher due to the nesting of sections. The proposed design procedure provides more accurate strength predictions for the built-up section columns compared to the existing methods.

THIN-WALLED STRUCTURES (2022)

添加到收藏夹

Article Construction & Building Technology

Direct Strength Method for Cold-Formed Steel Unlipped Channel Columns Subject to Local Buckling

Akshay Mangal Mahar et al.

Summary: This paper evaluates the strength of unlipped channel columns using the Direct Strength Method, finding that the aspect ratio significantly affects the local buckling strength of plain unlipped channel sections. The current DSM design specified in codes ignores this parameter, resulting in unconservative designs.

INTERNATIONAL JOURNAL OF STEEL STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

Global buckling strength of discretely fastened back-to-back built-up cold-formed steel columns

Akshay Mangal Mahar et al.

Summary: This study introduces a new design equation for built-up cold-formed steel columns to address inconsistencies in the AISI S100 specification. By considering the interaction between fastener spacing and overall slenderness ratio, a compound slenderness ratio is proposed to provide more accurate strength predictions.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)

添加到收藏夹

Article Engineering, Civil

Simplified design method of cold-formed steel columns with built-up box sections

Xuhong Zhou et al.

Summary: This study investigates the buckling behavior and ultimate strength of axially loaded pin-ended cold-formed steel built-up box section columns, considering the effects of local and local-flexural interactive buckling modes. Experimental and theoretical research were conducted, and a simplified design method was proposed based on test results and numerical analysis. The study highlights the importance of factors such as slenderness ratio, web depth-to-thickness ratio, and screw spacing in determining the ultimate strength of built-up columns.

ENGINEERING STRUCTURES (2021)

添加到收藏夹

Article Engineering, Civil

A Computational Study on Buckling Behavior of Cold-Formed Steel Built-Up Columns Using Compound Spline Finite Strip Method

Akshay Mangal Mahar et al.

Summary: This paper presents a computational methodology for calculating the critical buckling stress of built-up cold-formed steel columns with discrete fasteners, comparing with the buckling behavior of single sections. The study shows that a significant increment in buckling stress for a built-up section is observed when the fastener spacing is kept less than the critical buckling half-wavelength of respective modes. Additionally, the presence of sheathed wall studs leads to the elimination of global buckling deformations.

INTERNATIONAL JOURNAL OF STRUCTURAL STABILITY AND DYNAMICS (2021)

添加到收藏夹

Article Engineering, Civil

Built-up back-to-back cold-formed steel compression members failing by local and distortional buckling

Son Tung Vy et al.

Summary: This research focuses on the compression behavior and capacity of built-up back-to-back CFS channel sections, examining the effects of screw fastener characteristics and arrangements. It proposes a simple DSM-based design method after conducting compression tests, developing finite element models, and conducting a parametric study. The study aims to improve the accuracy of current design equations and provide recommendations for CFS design standards.

THIN-WALLED STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

Behavior and Design of Cold-Formed Steel Bolted Connections Subjected to Combined Actions

Seyed Mohammad Mojtabaei et al.

Summary: This study focuses on the failure mode of cold-formed steel bolted connections subject to combined axial compression, shear, and bending moment. Design equations for the compressive capacity of CFS bolted connections are developed based on geometric and material non-linear analysis with imperfections. Interaction equations for combined loading conditions are proposed, and reliability analyses are performed according to Eurocode and AISI standards. The findings suggest that a linear equation accurately captures the interaction between bending moment and axial force, with the effect of shear force on bending moment capacity being negligible.

JOURNAL OF STRUCTURAL ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

Built-up nested cold-formed steel compression members subject to local or distortional buckling

Son Tung Vy et al.

Summary: This research investigated the behavior and capacity of nested CFS channel compression members, carrying out experimental tests, developing finite element models, and conducting a parametric study. The study concluded that the accuracy of current design standards and research papers needs further validation, and recommended a simple design method based on DSM.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

Tests and design of built-up section columns

Dang Khoa Phan et al.

Summary: This study investigated the strength and behavior of built-up section columns composed of three or four lipped channel sections. It was found that singly-symmetric columns typically experienced local, distortional, and/or flexural-torsional buckling failure modes, while doubly-symmetric columns usually failed in local, distortional, and/or flexural buckling modes. The research proposed a design procedure for built-up sections experiencing flexural-torsional buckling, which is not explicitly stipulated in current design standards or previous studies.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)

添加到收藏夹

Article Engineering, Civil

Distortional buckling behavior of cold-formed steel built-up closed section columns

Yanchun Li et al.

Summary: This study investigated the distortional buckling behavior of cold-formed steel built-up columns, examining the effect of screw spacing on their mechanical properties. Results showed that the built-up columns exhibited a combination effect when the screw spacing was less than a certain value, and gradually approached the sum of two single columns when the screw spacing exceeded that value. Additionally, five different models were proposed to predict the critical load of distortional buckling.

THIN-WALLED STRUCTURES (2021)

添加到收藏夹

Article Construction & Building Technology

Improved design procedure for battened cold-formed steel built-up columns composed of lipped angles

M. Anbarasu et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2020)

添加到收藏夹

Article Engineering, Civil

Experimental investigation on cold-formed steel stiffened lipped channel columns undergoing local-distortional interaction

Man-Tai Chen et al.

THIN-WALLED STRUCTURES (2020)

添加到收藏夹

Article Engineering, Civil

Axial capacity of CFS built-up columns comprising of lipped channels with spacers: Nonlinear response and design

M. Anbarasu et al.

ENGINEERING STRUCTURES (2020)

添加到收藏夹

Article Construction & Building Technology

Flexural-torsional buckling strength of thin-walled channel sections with warping restraint

J. Sevugan Rajkannu et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2020)

添加到收藏夹

Article Construction & Building Technology

Local Buckling in Cold-Formed Steel Moment-Resisting Bolted Connections: Behavior, Capacity, and Design

Seyed Mohamad Mojtabaei et al.

JOURNAL OF STRUCTURAL ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Influence of chord compactness and slenderness on axial compression behavior of built-up battened CFS columns

M. Adil Dar et al.

JOURNAL OF BUILDING ENGINEERING (2020)

添加到收藏夹

Article Engineering, Civil

Compressive behavior of built-up double-box columns consisting of four cold-formed steel channels

Shaofeng Nie et al.

ENGINEERING STRUCTURES (2020)

添加到收藏夹

Article Construction & Building Technology

Experimental and numerical investigations on the axial capacity of cold-formed steel built-up box sections

Krishanu Roy et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2019)

添加到收藏夹

Article Construction & Building Technology

Axial compression behavior of laced cold-formed steel built-up columns with unstiffened angle sections

M. Adil Dar et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2019)

添加到收藏夹

Article Construction & Building Technology

Nonlinear behaviour of back-to-back gapped built-up cold-formed steel channel sections under compression

Krishanu Roy et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2018)

添加到收藏夹

Article Construction & Building Technology

Interaction of Local, Distortional, and Global Buckling in CFS Lipped Channel Compression Members

M. V. Anil Kumar et al.

JOURNAL OF STRUCTURAL ENGINEERING (2018)

添加到收藏夹

Article Engineering, Civil

Elastic buckling analysis of cold-formed steel built-up sections with discrete fasteners using the compound strip method

M. Abbasi et al.

THIN-WALLED STRUCTURES (2018)

添加到收藏夹

Article Engineering, Civil

GBTUL 2.0-A second-generation code for the GBT-based buckling and vibration analysis of thin-walled members

R. Bebiano et al.

THIN-WALLED STRUCTURES (2018)

添加到收藏夹

Article Engineering, Civil

Finite element analysis and design of cold-formed steel built-up closed section columns with web stiffeners

Jia-Hui Zhang et al.

THIN-WALLED STRUCTURES (2018)

添加到收藏夹

Article Construction & Building Technology

Interaction of Local, Distortional, and Global Buckling in CFS Lipped Channel Compression Members

M. V. Anil Kumar et al.

JOURNAL OF STRUCTURAL ENGINEERING (2018)

添加到收藏夹

Article Engineering, Civil

Behaviour of laced built-up cold-formed steel columns: Experimental investigation and numerical validation

M. Adil Dar et al.

THIN-WALLED STRUCTURES (2018)

添加到收藏夹

Article Engineering, Civil

End condition effect on distortional buckling of cold-formed steel columns with arbitrary length

Tianhua Zhou et al.

THIN-WALLED STRUCTURES (2017)

添加到收藏夹

Article Engineering, Civil

Experimental investigation and a novel direct strength method for cold-formed built-up I-section columns

Yan Lu et al.

THIN-WALLED STRUCTURES (2017)

添加到收藏夹

Article Engineering, Civil

Experimental investigation of built-up cold-formed steel section battened columns

Mohamed Dabaon et al.

THIN-WALLED STRUCTURES (2015)

添加到收藏夹

Article Engineering, Civil

Numerical investigation and design of cold-formed steel built-up open section columns with longitudinal stiffeners

Jia-Hui Zhang et al.

THIN-WALLED STRUCTURES (2015)

添加到收藏夹

Article Construction & Building Technology

Distortional Buckling of CFS Stiffened Lipped Channel Compression Members

M. V. Anil Kumar et al.

JOURNAL OF STRUCTURAL ENGINEERING (2014)

添加到收藏夹

Article Engineering, Civil

Ultimate load-carrying capacity of cold-formed thin-walled columns with built-up box and I section under axial compression

Yuanqi Li et al.

THIN-WALLED STRUCTURES (2014)

添加到收藏夹

Article Construction & Building Technology

Cold-Formed Steel Lipped Channel Columns Influenced by Local-Distortional Interaction: Strength and DSM Design

Ben Young et al.

JOURNAL OF STRUCTURAL ENGINEERING (2013)

添加到收藏夹

Article Engineering, Civil

Ultimate capacity of battened columns composed of four equal slender angles

M. A. El Aghoury et al.

THIN-WALLED STRUCTURES (2013)

添加到收藏夹

Article Construction & Building Technology

Design Strength of Locally Buckling Stub-Lipped Channel Columns

M. V. Anil Kumar et al.

JOURNAL OF STRUCTURAL ENGINEERING (2012)

添加到收藏夹

Article Engineering, Civil

Compression tests of cold-formed steel I-shaped open sections with edge and web stiffeners

Jia-Hui Zhang et al.

THIN-WALLED STRUCTURES (2012)

添加到收藏夹

Article Construction & Building Technology

Distortional buckling tests of cold-formed steel compression members at elevated temperatures

Thanuja Ranawaka et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2009)

添加到收藏夹

Article Construction & Building Technology

Design of cold-formed steel built-up closed sections with intermediate stiffeners

Ben Young et al.

JOURNAL OF STRUCTURAL ENGINEERING-ASCE (2008)

添加到收藏夹

Article Engineering, Civil

Behavior of cold-formed steel built-up I-sections

TA Stone et al.

THIN-WALLED STRUCTURES (2005)

添加到收藏夹

Article Construction & Building Technology

Behavior of cold-formed steel plain angle columns

E Ellobody et al.

JOURNAL OF STRUCTURAL ENGINEERING (2005)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.