☆ 4.7 Article

Effect of oxidizer dilution on thermophotovoltaic performance of premixed ammonia/hydrogen/air combustion in radial micro-combustor

FUEL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Thermodynamics

Effect of pins and exit-step on thermal performance and energy efficiency of hydrogen-fueled combustion for micro-thermophotovoltaic

Bo Xie et al.

Summary: By designing the combustor coupling with pins and exit-step configurations, the micro thermophotovoltaic system shows improved energy efficiency and thermal performance. The optimal length ratio of exit-step to combustor is found to be 0.66 for reducing exhaust loss, resulting in stable flame and high energy efficiency.

ENERGY (2022)

添加到收藏夹

Article Thermodynamics

Beyond the combustion chamber: Heat transfer and its impact on micro-thermophotovoltaic systems performance

Eliton Fontana et al.

Summary: The conversion of thermal radiation into electrical current in thermophotovoltaic devices is influenced by heat transfer, especially for micro-scale devices where heat management is crucial. A model considering wavelength-selective optical filters has been proposed to estimate cell efficiency by discretizing the radiation spectrum into bands and using average values. Results show the importance of optimal emitter/cell distance and secondary cooling mechanisms in improving cell efficiency.

ENERGY (2022)

添加到收藏夹

Review Energy & Fuels

Influencing factors of wall temperature and flame stability of micro-combustors in micro-thermophotovoltaic and micro-thermoelectric systems

Peng Qian et al.

Summary: Micro-thermophotovoltaic and micro-thermoelectric systems have attracted extensive attention for their compact configuration, no mechanical noise, wide fuel applicability, and high energy density. The focus of research has been on micro-combustors, with concerns about wall temperature and flame stability. Various micro-combustors with different designs have been proposed, but the effects of influential parameters need to be analyzed and summarized for further research.

FUEL (2022)

添加到收藏夹

Article Chemistry, Physical

Influence of CH4/air injection location on non-premixed flame blow-off limits in a novel micro-combustor

Lun Ma et al.

Summary: This paper develops a novel non-premixed CH4/air micro-combustor to avoid flame flash-back issue and extend flame blow-off limits. The influence of two different CH4/air injection locations on flame blow-off limits is numerically investigated, and the mechanisms in this micro-combustor are profoundly revealed. The results show that this novel configuration can anchor the flame without flame flash-back issue and significantly extend flammability. The larger blow-off limits are attained for the Air((in))/CH4(out) injection location compared to the Air((out))/CH4(in) injection location.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

添加到收藏夹

Article Engineering, Environmental

NOx emission reduction in ammonia-powered micro-combustors by partially inserting porous medium under fuel-rich condition

Siliang Ni et al.

Summary: This study investigates the NOx emission performance in fuel-rich combustion of ammonia using micro combustors with double-rib structure partially inserted with porous medium. The results show that the porous medium can effectively reduce NO generation and emission under a larger inlet velocity. Increasing the thermal conductivity of the porous material can greatly decrease the emission of NO, but increase the emission of N2O. Additionally, increasing the porosity of the porous material leads to an increase in NO emission but a decrease in N2O emission.

CHEMICAL ENGINEERING JOURNAL (2022)

添加到收藏夹

Article Energy & Fuels

Study on combustion characteristic of premixed H2/C3H8/air and working performance in the micro combustor with block

Qingguo Peng et al.

Summary: The combustion characteristics and thermal performance of premixed H-2/C3H8/air in a micro planar combustor with a block insert were experimentally and numerically tested. The effects of hydrogen blended fraction, equivalence ratio, flow rate, and block width on flame stability and heat transfer were discussed and analyzed. The results showed that adding hydrogen improved combustion stability in the micro combustor, and the lowest hydrogen blending mole fraction for a steady flame of the premixed H-2/C3H8/air was obtained through experimental study.

FUEL (2022)

添加到收藏夹

Article Energy & Fuels

Effect of intake method on ammonia/oxygen non-premixed combustion in the micro combustor with dual-inlet

Yi Zhang et al.

Summary: MTPV systems are receiving attention for their high energy density and compact size. A study using non-premixed combustion with ammonia as a carbon-free fuel showed improved thermal performance and reduced NO emissions. Optimization of inlet species, equivalence ratio, and total inlet velocity can further enhance performance, increasing outer wall temperature and decreasing NO emissions.

FUEL (2022)

添加到收藏夹

Article Chemistry, Physical

Reaction zone characteristics, thermal performance and NOx/N2O emissions analyses of ammonia MILD combustion

Amirreza Mohammadpour et al.

Summary: Numerical study of pure ammonia MILD combustion in a furnace reveals that lowering the furnace wall temperature and diluting the inlet air with nitrogen can improve the characteristics of the reaction zone, reduce fuel and oxidizer consumption rates, increase turbulent Reynolds number, and decrease exhaust emissions.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

添加到收藏夹

Article Chemistry, Physical

An integrated system for ammonia production from renewable hydrogen: A case study

Merve Ozturk et al.

Summary: This study presents an analysis and assessment study of an integrated system for producing ammonia, consisting of a cryogenic air separation unit, polymer electrolyte membrane electrolyzer, and reactor. The system's efficiency is impacted by solar radiation intensity and inlet air conditions, with an increase in solar influx leading to decreased efficiencies. Additionally, the mass flow rate of inlet air significantly affects ammonia production.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Experimental and numerical studies of the diluent influence (N2 , Ar, He, Xe) on stable premixed methane flames in micro-combustion

Hugo Chouraqui et al.

Summary: This study focuses on the influence of diluent on stable methane flames in a fused silica micro flow reactor, utilizing experimental and numerical investigations. Experimental methods are applied to different diluents to study their effects on methane flames, as well as their thermodynamic and transport properties. The numerical study supports experimental observations and provides insights that are difficult to achieve in micro-devices.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical investigation on a multi-channel micro combustor fueled with hydrogen for a micro-thermophotovoltaic system

Ziqiang He et al.

Summary: This study compared the heat transfer performance and energy output of different channel shapes MCMC and CMC in the MTPV system, finding that the MCMC with diamond channels had a higher outer wall temperature at a certain flow rate. Additionally, the double-layer MCMC with counterflow structure achieved the highest total energy conversion efficiency under specific conditions.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Engineering, Environmental

Mitigating NOx emissions from an ammonia-fueled micro-power system with a perforated plate implemented

Tao Cai et al.

Summary: The study investigates the effect of implementing a perforated plate on NOx emissions in ammonia-fueled micro-power systems, finding that an optimized perforated plate can significantly reduce NO emissions due to the formation of a low flame temperature recirculation zone. Additionally, increasing hole width helps minimize NO generation, while hole position variation leads to an opposite trend in NOx emissions.

JOURNAL OF HAZARDOUS MATERIALS (2021)

添加到收藏夹

Article Energy & Fuels

Heat transfer and entropy production evaluation on premixed hydrogen/air-fuelled micro-combustors with internal threads

Siliang Ni et al.

Summary: The proposed micro-combustor with tailored internal threads aims to improve the wall temperature uniformity and enhance the second law efficiency of a micro thermophotovoltaic (MTPV) system. Computational fluid dynamics simulations show that the corrugated thread structures can reduce flame temperature and improve heat transfer significantly. The study also reveals the impact of inlet velocity and nominal diameter on thermal performances of the system.

FUEL (2021)

添加到收藏夹

Article Chemistry, Physical

Effects of hydrogen addition to methane on the thermal and ignition delay characteristics of fuel-air, oxygen-enriched and oxy-fuel MILD combustion

E. Ebrahimi Fordoei et al.

Summary: The study demonstrates that adding H2 to CH4 can result in a more uniform temperature field with higher peak and average temperatures, while compensation for additional ignition delay time can be achieved by considering the presence of H2 in the fuel composition.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Chemical structure and laminar burning velocity of atmospheric pressure premixed ammonia/hydrogen flames

Ksenia N. Osipova et al.

Summary: This paper presents experimental data on the flame structure of laminar premixed ammonia and ammonia/hydrogen flames at different equivalence ratios and the laminar flame speed of ammonia/hydrogen flames. Experimental data were compared with modeling results obtained using detailed chemical-kinetic mechanisms of ammonia oxidation. The study shows that slightly rich conditions and increasing pressure can reduce NO formation in ammonia flames.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Chemistry, Physical

Investigation of thermal performance and energy conversion in a novel planar micro-combustor with four-corner entrances for thermo-photovoltaic power generators

Xiao Yang et al.

Summary: A novel planar micro-combustor design with four-corner entrances is proposed in this study, showing superior performance in terms of high-temperature uniformity, thermal efficiency, and energy efficiency compared to conventional designs. The implemented plate-insertion strategy effectively overcomes variations in combustor performance under different operating conditions. This work provides important insights and design ideas for the development of high-efficiency micro-power systems.

JOURNAL OF POWER SOURCES (2021)

添加到收藏夹

Article Thermodynamics

Numerical investigations on hydrogen-fueled micro-cylindrical combustors with cavity for micro-thermophotovoltaic applications

Wei Zuo et al.

Summary: The study found that the micro-cylindrical combustor with cavity has better thermal performance compared to the one without cavity. By analyzing the effects of cavity length and depth, the optimal cavity size was determined, and it was concluded that the combustor with cavity has better potential for applications in micro-TPV systems.

ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

Effect analysis on energy conversion enhancement and NOx emission reduction of ammonia/hydrogen fuelled wavy micro-combustor for micro-thermophotovoltaic application

Lei Han et al.

Summary: The study found that the wavy combustors have higher average temperatures and improved temperature uniformity compared to conventional smooth combustors. The flame stability of hydrogen/ammonia blended combustion is better in the wavy combustors. NOx emission reduction can be achieved by increasing the nitrogen fuel mass ratio. This research demonstrates the effective design of a micro-combustor with enhanced thermal performance and reduced NOx emissions.

FUEL (2021)

添加到收藏夹

Article Energy & Fuels

Thermal performance and NOx emission characteristics studies on a premixed methane-ammonia-fueled micro-planar combustor

Yuze Sun et al.

Summary: This study numerically investigates the thermal and emission performances of a micro-planar combustor fueled with a methane/ammonia mixture. The results show complex variations in outer wall temperature and non-uniformity with different parameters, as well as contradictory trends in CO and NO emissions with equivalence ratios.

FUEL (2021)

添加到收藏夹

Article Chemistry, Applied

Energy conversion efficiency improvement studies on unconventional premixed micro-combustors partially inserted with porous medium

Siliang Ni et al.

Summary: This study investigates the thermal performance and radiation efficiency of micro-combustors with curved surfaces through experiments and numerical simulations. Results show that double-channel combustors have higher efficiency and porous medium improves temperature uniformity. The T-shaped combustor exhibits the best performance under certain conditions.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Energy & Fuels

Combustion characteristics of hydrogen-air mixture in a radial micro combustor for using in thermophotovoltaic devices

Alireza Alipoor et al.

Summary: This research aims to investigate the performance and feasibility of a radial micro combustion chamber by numerical study of combustion characteristics of H-2-air pre-mixture and calculation of emitter and total efficiency of the system. Results show that the inlet velocity significantly affects the location of the combustion zone, while the equivalence ratio impacts the combustion temperature. Wall thermal conductivity and radiation emissivity have significant influence on the system's total efficiency.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2021)

添加到收藏夹

Article Chemistry, Physical

Comparative investigation of combustion and thermal characteristics of a conventional micro combustor and micro combustor with internal straight/spiral fins for thermophotovoltaic system

Ziqiang He et al.

Summary: The study focuses on the impact of hydrogen mass flow rate, equivalence ratio, and materials on the thermal performance of micro-thermophotovoltaic (MTPV) system, providing suggestions for improving energy output.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Thermal performances and emitter efficiency improvement studies on premixed micro-combustors with different geometric shapes for thermophotovoltaics applications

Siliang Ni et al.

Summary: This study compared the thermal performance and efficiency of unconventional T- and Y-shaped micro-combustors with the traditional I-shaped one. Results showed significant improvements in thermal performance and efficiency for T- and Y-shaped combustors under the same conditions. Optimization of parameters can enhance combustion efficiency.

ENERGY (2021)

添加到收藏夹

Article Chemistry, Applied

Experimental and theoretical investigations of a new cascaded reactor for ammonia as a renewable fuel

H. Ishaq et al.

Summary: This study developed a cascaded ammonia synthesis system by serially connecting two ammonia synthesis reactors with pre-reduced KMR catalyst, leading to improved synthesis rates. Experimental results showed that under the right operating temperature and pressure, employing a cascaded ammonia synthesis system can increase ammonia conversion efficiencies.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Chemistry, Applied

Role of hydrogen addition in propane/air flame characteristic and stability in a micro-planar combustor

Aikun Tang et al.

Summary: Experimental study on micro-scale combustion with a micro-planar quartz combustor shows that blending hydrogen significantly extends flame stability by overcoming flame instability and inhibiting flame type transition. The addition of hydrogen affects flame dynamics and helps maintain flame symmetry.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Chemistry, Applied

Enhancing heat transfer performance analyses of a hydrogen-fueled meso-combustor with staggered bluff-bodies

Tao Cai et al.

Summary: This study aims to improve the energy conversion efficiency of a thermo-photo-voltaic system by optimizing combustor performance through the use of staggered bluff-bodies. The implementation of staggered bluff-bodies significantly enhances heat transfer performance and increases mean wall temperature. Results also show that the equivalence ratio and dimensions of the staggered bluff-bodies have a significant impact on system performance.

FUEL PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Chemistry, Physical

Influence of hole size and number on pressure drop and energy output of the micro-cylindrical combustor inserting with an internal spiral fin with holes

Ting Zhao et al.

Summary: The study found that the spiral fin opening can reduce pressure loss and optimize outer wall temperature distribution, but has a negative impact on the mean outer wall temperature and energy output of the micro combustor and MTPV systems. With the increase of the hole size and hole number of the spiral fin, the pressure loss decreases, outer wall temperature uniformity improves significantly, but the mean outer wall temperature and total energy output decrease.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Evaluation of NOx emissions characteristics in a CO2-Free micro-power system by implementing a perforated plate

Tao Cai et al.

Summary: Ammonia, as a carbon-free fuel with high hydrogen content, has potential applications in transportation, propulsion, and power generation sectors. However, direct combustion of ammonia leads to high NOx emission, which needs to be mitigated. Factors such as plate porosity, thickness, distance, and inlet pressure play important roles in reducing NO formation.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2021)

添加到收藏夹

Article Energy & Fuels

Performance Evaluation of H2/Air Premixed Combustion in a Suddenly Expanded Microcombustor with Wall Fin

Arees Qamareen et al.

Summary: The study investigated the influence of a 2D, axisymmetric microcombustor with a backward-facing step and triangular wall fin on combustion performance, with numerical results indicating that the wall fin blockage ratio alters the reaction zone and significantly improves combustor performance at lower inlet velocities. The location and shape of the wall fin were found to influence the temperature distribution, while a higher blockage ratio had adverse effects on combustion characteristics at higher inlet velocities.

ENERGY TECHNOLOGY (2021)

添加到收藏夹

Article Thermodynamics

Maps of flame dynamics for premixed lean hydrogen-air combustion in a heated microchannel

Alireza Alipoor et al.

ENERGY (2020)

添加到收藏夹

Article Energy & Fuels

Bluff-body effect on thermal and NOx emission characteristics in a micro-planar combustor fueled with premixed ammonia-oxygen

Tao Cai et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2020)

添加到收藏夹

Article Chemistry, Applied

Effects of fuel composition and wall thermal conductivity on thermal and NOx emission performances of an ammonia/hydrogen-oxygen micro-power system

Tao Cai et al.

FUEL PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Energy & Fuels

NOx emission and thermal performances studies on premixed ammonia-oxygen combustion in a CO2-free micro-planar combustor

Tao Cai et al.

FUEL (2020)

添加到收藏夹

Article Chemistry, Applied

Experimental study on N2O and NOx emission characteristics of five high-volatile fuels in bubbling bed combustion

Miao Miao et al.

FUEL PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Chemistry, Physical

Investigation of an integrated system with industrial thermal management options for carbon emission reduction and hydrogen and ammonia production

H. Ishaq et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

The numerical study of the energy and exergy efficiencies of the micro-combustor by the internal micro-fin for thermophotovoltaic systems

Ebrahim Nadimi et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Energy & Fuels

Enhancement of hydrogen combustion efficiency by helium dilution in a micro-combustor with wall cavities

Aiwu Fan et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2018)

添加到收藏夹

Article Thermodynamics

Effect of backward facing step on radiation efficiency in a micro combustor

Hosein Faramarzpour et al.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2018)

添加到收藏夹

Article Chemistry, Applied

Numerical study on energy conversion performance of micro-thermophotovoltaic system adopting a heat recirculation micro-combustor

Aikun Tang et al.

FUEL PROCESSING TECHNOLOGY (2018)

添加到收藏夹

Article Chemistry, Physical

Power-to-ammonia in future North European 100 % renewable power and heat system

Jussi Ikaheimo et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2018)

添加到收藏夹

Article Energy & Fuels

Numerical study of hydrogen-air combustion characteristics in a novel micro-thermophotovoltaic power generator

Alireza Alipoor et al.

APPLIED ENERGY (2017)

添加到收藏夹

Article Thermodynamics

Effect of the length of a plate flame holder on flame blowout limit in a micro-combustor with preheating channels

Jianlong Wan et al.

COMBUSTION AND FLAME (2016)

添加到收藏夹

Article Thermodynamics

Structure of premixed ammonia plus air flames at atmospheric pressure: Laser diagnostics and kinetic modeling

Christian Brackmann et al.

COMBUSTION AND FLAME (2016)

添加到收藏夹

Article Energy & Fuels

An experimental study of methane-oxygen-carbon dioxide premixed flame dynamics in non-adiabatic cylinderical meso-scale reactors with the backward facing step

Mohammadreza Baigmohammadi et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2015)

添加到收藏夹

Article Engineering, Environmental

Flame-anchoring mechanisms of a micro cavity-combustor for premixed H2/air flame

Jianlong Wan et al.

CHEMICAL ENGINEERING JOURNAL (2015)

添加到收藏夹

Article Thermodynamics

An experimental study of the effects of equivalence ratio, mixture velocity and nitrogen dilution on methane/oxygen pre-mixed flame dynamics in a meso-scale reactor

Soroush Sarrafan Sadeghi et al.

ENERGY CONVERSION AND MANAGEMENT (2014)

添加到收藏夹

Article Thermodynamics

Experimental study of n-heptane/air combustion in meso-scale burners with porous media

Junwei Li et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

PEEK/SiO2 Composites with High Thermal Stability for Electronic Applications

R. K. Goyal et al.

ELECTRONIC MATERIALS LETTERS (2013)

添加到收藏夹

Review Thermodynamics

A review on microcombustion: Fundamentals, devices and applications

Niket S. Kaisare et al.

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2012)

添加到收藏夹

Article Thermodynamics

Experimental investigation on flame pattern formations of DME-air mixtures in a radial microchannel

Aiwu Fan et al.

COMBUSTION AND FLAME (2010)

添加到收藏夹

Article Thermodynamics

Ammonia chemistry in oxy-fuel combustion of methane

Teresa Mendiara et al.

COMBUSTION AND FLAME (2009)

添加到收藏夹

Article Environmental Sciences

Combating global warming via non-fossil fuel energy options

Marc A. Rosen

INTERNATIONAL JOURNAL OF GLOBAL WARMING (2009)

添加到收藏夹

Article Thermodynamics

Dynamics of premixed hydrogen/air flames in microchannels

Gianmarco Pizza et al.

COMBUSTION AND FLAME (2008)

添加到收藏夹

Article Thermodynamics

Regime diagrams and characteristics of flame patterns in radial microchannels with temperature gradients

Aiwu Fan et al.

COMBUSTION AND FLAME (2008)

添加到收藏夹

Article Engineering, Electrical & Electronic

Experimental study on flame pattern formation and combustion completeness in a radial microchannel

Aiwu Fan et al.

JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2007)

添加到收藏夹

Article Thermodynamics

On the formation of multiple rotating Pelton-like flame structures in radial microchannels with lean methane-air mixtures

Sudarshan Kumar et al.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2007)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.