☆ 4.7 Article

Effect of YSZ/TaSi2-MCrAlY thermal barrier coatings on oxidation resistance in air and water vapor

CERAMICS INTERNATIONAL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Corrosion behavior of high-entropy (La0.2Nd0.2Sm0.2Eu0.2Gd0.2)Ce2O7 in different aggressive molten salt

Yun Xue et al.

Summary: The high-entropy material HECO shows smaller corrosion depth than LCO except for partial exfoliation. The sluggish diffusion effect of HECO inhibits nucleation of corrosion products and leads to a reduction in corrosion depth through horizontal growth. Additionally, the correlation between the aggressiveness of molten salt and the corrosion alleviation is observed.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Size effects on high temperature oxidation of MCrAlY coatings processed via APS and HVOF depositions

Ali Kalush et al.

Summary: This paper demonstrates the impact of defects inherited from the deposition processes on the lifetime of MCrAlY coatings. The oxidation behavior of two coatings, processed by different projection techniques, was investigated. Thicker coatings were found to have a higher oxidation rate and experienced chemical failure. Additionally, thicker coatings also developed mechanically induced chemical failure.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Chemistry, Physical

Effects of Stepped Heating on the Initial Growth of Oxide Scales on NiCrAlHf Bond Coat Alloy under Air and Water Vapor Atmospheres

Yang He et al.

Summary: Temperature and atmosphere significantly affect the oxidation of MCrAlY (M = Ni, Co) bond coating. The initial growth behavior of the NiCrAlHf bond coat alloy was studied at 1100 degrees C under different atmospheric conditions and heating methods. The results showed that using stepped heating at low temperatures led to the formation of a thick Al2O3 oxide layer and large HfO2 particles. However, in air and water vapor atmospheres, the oxide scale was thinner and the HfO2 precipitates were smaller in stepped heating compared to constant heating, possibly due to different microstructures induced by the size and distribution of the HfO2 particles, particularly voids within the oxide scale.

MATERIALS (2022)

添加到收藏夹

Article Materials Science, Ceramics

High-entropy (La0.2Nd0.2Sm0.2Eu0.2Gd0.2)2Ce2O7: A potential thermal barrier material with improved thermo-physical properties

Yun Xue et al.

Summary: By designing and synthesizing high-entropy (La0.2Nd0.2Sm0.2Eu0.2Gd0.2)(2)Ce2O7, the thermal expansion property of oxides is improved and the thermal conductivity is reduced. The multicomponent material has a higher thermal expansion coefficient and prominent thermal insulation behavior, and maintains phase stability at high temperatures, making it a promising TBC material.

JOURNAL OF ADVANCED CERAMICS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A new strategy for long-term complex oxidation of MAX phases: Database generation and oxidation kinetic model establishment with aid of machine learning

Chunyu Guo et al.

Summary: In this study, a comprehensive oxidation database of MAX phases was generated using a machine learning model combined with experimental data. The long-term complexity of the oxidation process was accurately addressed, providing guidance for understanding the complex oxidation of other ceramics and alloys.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Multidisciplinary Sciences

Effect of Sn doping concentration on the oxidation of Al-containing MAX phase (Ti3AlC2) combining simulation with experiment

Chunyu Guo et al.

Summary: The effect of Sn doping concentration on the oxidation behavior of Ti3AlC2 was investigated, and it was found that excessive Sn doping impairs its oxidation resistance when the concentration exceeds 10 mol%.

FUNDAMENTAL RESEARCH (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

Progress in cognition of gas-solid interface reaction for non-oxide ceramics at high temperature

Enhui Wang et al.

Summary: With the advancement of science and technology, non-oxide ceramics (NOCs) play a crucial role in various fields at high temperatures. However, they are prone to complex gas-solid interface reactions under harsh conditions, emphasizing the importance of understanding these reactions for material performance improvement. Different approaches, including theoretical, experimental, and simulative methods, are used to efficiently study the reaction behavior and mechanisms of NOCs at the gas-solid interface.

CRITICAL REVIEWS IN SOLID STATE AND MATERIALS SCIENCES (2021)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and oxidation behaviour of MoSi2 coating combined MoB diffusion barrier layer on Mo substrate at 1300 °C

Ruixiong Zhai et al.

Summary: Using a two-step pack cementation method, double layers of MoSi2-MoB were applied on the surface of a Mo substrate to enhance its oxidation resistance at high temperatures. The formation of a dense and continuous SiO2 layer with low O-2 permeability contributed to the excellent high-temperature oxidation resistance of the double layers.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Ceramics

Formation of MoSi2 and Si/MoSi2 coatings on TZM (Mo-0.5Ti-0.1Zr-0.02C) alloy by hot dip silicon-plating method

Yingyi Zhang et al.

Summary: MoSi2 and Si-MoSi2 composite coatings with fine MoSi2 grain size and high surface silicon concentration were successfully deposited on TZM alloy using a hot dip silicon-plating method. The gradient structure of the coatings, including MoSi2 layer, Mo5Si3C layer, and Si-MoSi2 layer, contributes to reducing stress mutation and crack propagation. SEM and CLSM results demonstrate that a significant portion of MoSi2 grains are covered by silicon layer, leading to very low coating surface roughness when deposition time exceeds 10 minutes.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Screening for Al2O3 failure in MCrAlY APS coatings using short-term oxidation at high temperature

Damien Texier et al.

Summary: High temperature oxidation behavior of APS processed NiCoCrAlY coating was investigated at 1150 ?C. Intrinsic chemical failure (InCF) occurred after the full consumption of Al, leading to Cr2O3 growth and CrN precipitation at the Al2O3/alloy interface. Mass gain slowed down after InCF, and even resulted in mass loss associated with the volatilization of Cr2O3.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of Ta on oxidation resistance of TiC/hastelloy composites

Qian Qi et al.

Summary: This study investigates the effect of Ta on the oxidation resistance of TiC/hastelloy composites and finds that increasing Ta content can optimize the oxidation resistance by forming an oxide scale with CrTaO4. Ta-doped TiO2 inhibits inward diffusion of oxygen, while CrTaO4 suppresses outward diffusion of Ni, Ti, and Cr, resulting in better protective effects for the composites.

JOURNAL OF MATERIALS SCIENCE (2021)

添加到收藏夹

Article Materials Science, Ceramics

Effects of Ta content on the oxidation and high-temperature tribological behaviors of (Zr, Ta) N coating deposited by double-cathode glow plasma alloy

Mengjuan Yin et al.

Summary: This research investigated the surface properties of ZrN, TaN, and (Zr, Ta)N coatings with different Ta contents, revealing that the addition of Ta can enhance oxidation resistance, reduce thermal stress, and decrease the wear rate of the coatings. The formation of a dense (Zr, Ta)-rich oxide on the coating surface contributes to the improved performance of the coatings.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Characterization of MCrAlY/nano-Al2O3 nanocomposite powder produced by high-energy mechanical milling as feedstock for high-velocity oxygen fuel spraying deposition

F. Ghadami et al.

Summary: Al2O3 nanoparticles and MCrAlY/nano-Al2O3 nanocomposite powder can be produced using high-energy ball milling, suitable for thermal spraying coating. The ball-milled Al2O3 powder after a long duration has the smallest crystallite size and the highest lattice strain, while the particle size of MCrAlY/nano-Al2O3 nanocomposite powder decreases with increasing mechanical-milling duration.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Low-pressure plasma spraying of ZrB2-SiC coatings on C/C substrate by adding TaSi2

Rui-qiang Wang et al.

Summary: The TaSi2 modified ZrB2-SiC coatings were prepared to improve density and ablation resistance. Ta element was mainly present in the form of fine particles with nanoscale in the coatings, contributing to the reduction of porosity and enhancement of mechanical properties and ablation resistance.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Thermal barrier coating for diesel engine application - A review

Vishwanath S. Godiganur et al.

Summary: Thermal barrier coatings (TBCs) show potential for improving efficiency in diesel engines, with different materials used to adapt to low-temperature applications compared to gas turbines. This paper provides a simplified review of the durability and reliability of TBCs in diesel engines, focusing on aspects such as residual stress, thermal cycling performance, thermal conductivity, and thermal reflectance.

MATERIALS TODAY-PROCEEDINGS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of water vapour on morphology of the Si/Ti-rich phase at the interface between oxide layer and aluminide coating

Chao Li et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Ceramics

Synergistic effect of CeO2 and Al2O3 nanoparticle dispersion on the oxidation behavior of MCrAlY coatings deposited by HVOF

F. Ghadami et al.

CERAMICS INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Ceramics

Preparation, characterization and oxidation behavior of CeO2 -gradient NiCrAlY coatings applied by HVOF thermal spraying process

F. Ghadami et al.

CERAMICS INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of water vapor on the failure behavior of thermal barrier coating with Hf-doped NiCoCrAlY bond coating

Wenhao Duan et al.

JOURNAL OF MATERIALS RESEARCH (2019)

添加到收藏夹

Article Materials Science, Ceramics

Ultra-high temperature oxidation resistance of ZrB2-20SiC coating with TaSi2 addition on siliconized graphite

Yan Ren et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Chemistry, Physical

Key issues of MoSi2-UHTC ceramics for ultra high temperature heating element applications: Mechanical, electrical, oxidation and thermal shock behaviors

Lu Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Structural characteristics and high-temperature oxidation behavior of HVOF sprayed nano-CeO2 reinforced NiCoCrAlY nanocomposite coatings

F. Ghadami et al.

SURFACE & COATINGS TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of test atmosphere composition on high-temperature oxidation behaviour of CoNiCrAlY coatings produced from conventional and ODS powders

T. Huang et al.

MATERIALS AT HIGH TEMPERATURES (2018)

添加到收藏夹

Review Chemistry, Physical

Influence of water vapour on the HfO2 distribution within the oxide layer on CoNiCrAlHf alloys

Chao Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Materials Science, Ceramics

Oxidation of β-SiC at high temperature in Ar/O2, Ar/CO2, Ar/H2O gas mixtures: Kinetic study of the silica growth in the passive regime

Mathieu Q. Brisebourg et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Magnetron sputter deposition of zirconium-silicide coating for mitigating high temperature oxidation of zirconium-alloy

Hwasung Yeom et al.

SURFACE & COATINGS TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Evolution of microstructure and radiative property of metal silicide-glass hybrid coating for fibrous ZrO2 ceramic during high temperature oxidizing atmosphere

Gaofeng Shao et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Chemistry, Physical

Influence of siliconizing on the oxidation behavior of plasma sprayed MoSi2 coating for niobium based alloy

Jia Sun et al.

INTERMETALLICS (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and thermal stability of TaSi2 coating fabricated by vacuum plasma spray

Yaran Niu et al.

SURFACE & COATINGS TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Ceramics

Effect of TGO Thickness on Thermal Cyclic Lifetime and Failure Mode of Plasma- Sprayed TBCs

Hui Dong et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of water vapor on the 1100 °C oxidation behavior of plasma-sprayed TBCs with HVOF NiCoCrAlX bond coatings

J. A. Haynes et al.

SURFACE & COATINGS TECHNOLOGY (2013)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

A Simple Expression for Predicting the Oxidation Limited Life of Thin Components Manufactured from FCC High Temperature Alloys

D. J. Young et al.

OXIDATION OF METALS (2012)

添加到收藏夹

Article Materials Science, Ceramics

Rapid consolidation of nanostructured TaSi2 from mechanochemically synthesized powder by high frequency induction heated sintering

In-Jin Shon et al.

CERAMICS INTERNATIONAL (2011)

添加到收藏夹

Review Materials Science, Multidisciplinary

Mechanical behaviour and oxidation resistance of structural silicides

R Mitra

INTERNATIONAL MATERIALS REVIEWS (2006)

添加到收藏夹

Article Crystallography

Crystallization improvement of Ta2O5 thin films by the addition of water vapor

AP Huang et al.

JOURNAL OF CRYSTAL GROWTH (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Defect structures in TaSi2 thin films produced by co-sputtering

H Inui et al.

ACTA MATERIALIA (2003)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.