4.7 Article

Tuning ceramic content, mechanical and ablative properties of C/C-ZrC-ZrxCuy composites via using various C/C skeletons

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Materials Science, Ceramics

Effect of CVI SiC content on ablation and mechanism of C/C-SiC-ZrC-Cu composites

Yuanqi Weng et al.

Summary: C/C-SiC-ZrC-Cu composites were fabricated using different infiltration methods, and new phases of Cu6.69Si and Cu3Si were generated during Cu infiltration. The formed phases improved the wettability and interface combination between Cu and the carbon matrix. The ablation tests showed that the CVI SiC content significantly affected the structure of the protective oxide layer and had inverse effects on the ablation rate at different temperatures. The formed Si-Zr-C-O and Si-Cu-CO layers during ablation prevented carbon matrix oxidation.

CERAMICS INTERNATIONAL (2022)

Article Materials Science, Multidisciplinary

Structure evolution and ablative mechanism of C/C-ZrC-ZrxCuy composites with low porosity fabricated by pressure assisted reactive melt infiltration

Yuanqi Weng et al.

Summary: C/C-ZrC-ZrxCuy composites were fabricated using the PARMI process, yielding a matrix with three different ZrC-ZrxCuy regions and sequentially decreasing ZrC particle sizes. The heat-absorbing effect of the Cu phase slowed down surface temperature increase during 30 seconds of ablation. After 60 seconds of ablation, the porous ZrO2 skeleton transformed into a protective integrated cover, reducing the ablation rates of the composites significantly.

CORROSION SCIENCE (2022)

Article Nanoscience & Nanotechnology

Correlation of C/C preform density and microstructure and mechanical properties of C/C-ZrC-based ultra-high-temperature ceramic matrix composites

Hao Zhang et al.

Summary: This study investigated the correlation of C/C preform density with the microstructure and mechanical properties of C/C-ZrC composites, revealing that the composite density decreased with increasing preform density and the flexural strength initially increased and then decreased with preform density. The highest flexural strength of 241 MPa was achieved at a C/C preform density of 1.28 g/cm(3).

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Article Materials Science, Ceramics

Microstructure and mechanical performance evolution of C/C-ZrC composites exposed to oxyacetylene flame

Tianyu Liu et al.

Summary: The C/C-ZrC composites were prepared using ICVI and RMI methods. Ablation behavior of the composites was studied under oxyacetylene flame. The results showed that with increased ablation time, the ablation rates increased initially and then stabilized, while the flexural strength and modulus of the composites significantly increased after 15 seconds of ablation.

CERAMICS INTERNATIONAL (2021)

Article Materials Science, Ceramics

Effects of preform pore structure on infiltration kinetics and microstructure evolution of RMI-derived Cf/ZrC-ZrB2-SiC composite

Xiaowu Chen et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Article Chemistry, Physical

Oxygen adsorption on ideal ZrB2 and ZrC surfaces

Chunyu Cheng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Article Materials Science, Ceramics

Effect of ZrC amount and distribution on the thermomechanical properties of Cf/SiC-ZrC composites

Haijun Zhou et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2019)

Article Materials Science, Multidisciplinary

Influence of diamond graphitization on the microstructure and performance of micro-diamond modified C/C composites

Lei Chen et al.

DIAMOND AND RELATED MATERIALS (2019)

Article Materials Science, Ceramics

Microstructure and ablation properties of La2O3 modified C/C-SiC composites prepared via precursor infiltration pyrolysis

Cunqian Fang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Article Materials Science, Multidisciplinary

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Zhe Zhou et al.

ADVANCED ENGINEERING MATERIALS (2018)

Article Materials Science, Multidisciplinary

Microstructural development of a C/C-ZrC-Cu composite prepared by reactive melt infiltration with Zr/Cu powder mixture

Huang Wu et al.

MATERIALS CHARACTERIZATION (2018)

Article Materials Science, Coatings & Films

Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

Zhe Zhou et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2016)

Article Materials Science, Multidisciplinary

Ablative and Mechanical Properties of C/C-ZrC Composites Prepared by Precursor Infiltration and Pyrolysis Process

Kezhi Li et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2015)

Article Materials Science, Multidisciplinary

Comparison of ablative behaviour for ZrC and ZrC-Cu doped carbon/carbon composites in oxyacetylene torch environment

Z. H. Hao et al.

MATERIALS RESEARCH INNOVATIONS (2014)

Article Nanoscience & Nanotechnology

Fabrication and properties of PIP 3D Cf/ZrC-SiC composites

Chunlei Yan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Article Materials Science, Multidisciplinary

Mechanism of ablation of 3D C/ZrC-SiC composite under an oxyacetylene flame

Si'an Chen et al.

CORROSION SCIENCE (2013)

Article Materials Science, Multidisciplinary

Fabrication of Cf/ZrC composites by infiltrating Cf/C performs with Zr-Cu alloys

Yulin Zhu et al.

MATERIALS LETTERS (2013)

Article Nanoscience & Nanotechnology

Influence of reactive melt infiltration parameters on microstructure and properties of low temperature derived Cf/ZrC composites

Dong Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

Article Materials Science, Ceramics

Phase diagram of the Al2O3-HfO2-Y2O3 system

S. M. Lakiza et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2011)

Article Engineering, Industrial

A new processing technique for copper-graphite multifilamentary nanocomposite wire: Microstructures and electrical properties

A. Guillet et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)

Article Materials Science, Multidisciplinary

Oxygen adsorption on Cu(100): First-principles pseudopotential calculations

M Alatalo et al.

PHYSICAL REVIEW B (2004)