相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Processing and mechanical characterization of short carbon fiber-reinforced epoxy composites for material extrusion additive manufacturing
Nadim S. Hmeidat et al.
COMPOSITES PART B-ENGINEERING (2021)
Fibre bridging and nozzle clogging in 3D printing of discontinuous carbon fibre-reinforced polymer composites: coupled CFD-DEM modelling
Hao Zhang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Current status and future directions of fused filament fabrication
Sunpreet Singh et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing
Peng Wang et al.
COMPOSITES PART B-ENGINEERING (2020)
Advances in fused deposition modeling of discontinuous fiber/polymer composites
Chao Hu et al.
CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2020)
Mechanical characteristics of wood, ceramic, metal and carbon fiber-based PLA composites fabricated by FDM
Zhaobing Liu et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)
Mechanical characterization of FDM 3D printing of continuous carbon fiber reinforced PLA composites
M. Heidari-Rarani et al.
COMPOSITES PART B-ENGINEERING (2019)
Interfacial bonding strength of short carbon fiber/acrylonitrile-butadiene-styrene composites fabricated by fused deposition modeling
Wei Zhang et al.
COMPOSITES PART B-ENGINEERING (2018)
Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling
Evgeniy G. Gordeev et al.
PLOS ONE (2018)
Properties of oriented carbon fiber/polyamide 12 composite parts fabricated by fused deposition modeling
Guangxin Liao et al.
MATERIALS & DESIGN (2018)
Effect of process parameters on tensile strength of FDM printed PLA part
Shilpesh R. Rajpurohit et al.
RAPID PROTOTYPING JOURNAL (2018)
Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers
Rafael Thiago Luiz Ferreira et al.
COMPOSITES PART B-ENGINEERING (2017)
3D printing of polymer matrix composites: A review and prospective
Xin Wang et al.
COMPOSITES PART B-ENGINEERING (2017)
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Ryosuke Matsuzaki et al.
SCIENTIFIC REPORTS (2016)
Effects of fiber orientation and anisotropy on tensile strength and elastic modulus of short fiber reinforced polymer composites
Seyyedvahid Mortazavian et al.
COMPOSITES PART B-ENGINEERING (2015)
Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling
Fuda Ning et al.
COMPOSITES PART B-ENGINEERING (2015)
Thermo-mechanical Characterization of Metal/Polymer Composite Filaments and Printing Parameter Study for Fused Deposition Modeling in the 3D Printing Process
Seyeon Hwang et al.
JOURNAL OF ELECTRONIC MATERIALS (2015)
Comparison of tribological behaviour for Nylon6-Al-Al2O3 and ABS parts fabricated by fused deposition modelling This paper reports a low cost composite material that is more wear-resistant than conventional ABS
Kamaljit Boparai et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2015)
Highly oriented carbon fiber-polymer composites via additive manufacturing
Halil L. Tekinalp et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2014)
Influence of pressure on polyamide 66 shear viscosity: a case study towards polar polymers behavior
Simona Ceccia et al.
RHEOLOGICA ACTA (2014)
Influence of temperature and thickness on the off-axis behaviour of short glass fibre reinforced polyamide 6.6-cyclic loading
M. De Monte et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Nanofiber-reinforced polymers prepared by fused deposition modeling
ML Shofner et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2003)