相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Measurement and analysis of machining induced tribological characteristics in dual jet minimum quantity lubrication assisted turning of duplex stainless steel
Munish Kumar Gupta et al.
MEASUREMENT (2022)
Impact of hybrid cooling approach on milling and surface morphological characteristics of Nimonic 80A alloy
Nimel Sworna Ross et al.
JOURNAL OF MANUFACTURING PROCESSES (2022)
Investigation of signal behaviors for sensor fusion with tool condition monitoring system in turning
Mustafa Kuntoglu et al.
MEASUREMENT (2021)
Sustainable milling of Ti-6Al-4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment
Muhammad Jamil et al.
JOURNAL OF CLEANER PRODUCTION (2021)
Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect
Danil Yu Pimenov et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)
Cooling techniques to improve the machinability and sustainability of light-weight alloys: A state-of-the-art review
Murat Sarikaya et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Investigation of microstructure, mechanical and machinability properties of Mo-added steel produced by powder metallurgy method
Mehmet Akif Erden et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Tool Wear and Surface Evaluation in Drilling Fly Ash Geopolymer Using HSS, HSS-Co, and HSS-TiN Cutting Tools
Mohd Fathullah Ghazali et al.
MATERIALS (2021)
A novel method for improving drilling performance of CFRP/Ti6AL4V stacked materials
Nafiz Yasar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
A review on conventional and advanced minimum quantity lubrication approaches on performance measures of grinding process
Munish Kumar Gupta et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Circulating purification of cutting fluid: an overview
Xifeng Wu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Influence of duplex jets MQL and nano-MQL cooling system on machining performance of Nimonic 80A
Mehmet Erdi Korkmaz et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Review on design and development of cryogenic machining setups for heat resistant alloys and composites
Navneet Khanna et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Enhancing cutting tool sustainability based on remaining useful life prediction
Huibin Sun et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Comparative evaluation of soybean oil-based MQL flow rates and emulsion flood cooling strategy in high-speed face milling of Inconel 718
Anthony Chukwujekwu Okafor et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Comparative performance studies of turning 4140 steel with TiC/TiCN/TiN-coated carbide inserts using MQL, flooding with vegetable cutting fluids, and dry machining
Rukmini Srikant Revuru et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
A decision support methodology for integrated machining process and operation plans for sustainability and productivity assessment
Qais Y. Hatim et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
A review of the chip breaking methods for continuous chips in turning
Bahattin Yilmaz et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Tool wear, surface quality, and residual stresses analysis of micro-machined additive manufactured Ti-6Al-4V under dry and MQL conditions
Waqas Khaliq Khan et al.
TRIBOLOGY INTERNATIONAL (2020)
Performance analysis of coated carbide tool in turning of Nimonic 80A superalloy under different cutting environments
Mustafa Gunay et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
The effects of cryogenic cooling on the grinding process of polyether ether ketone (PEEK)
Mohammad Khoran et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Sustainability-based performance evaluation of hybrid nanofluid assisted machining
Aqib Mashood Khan et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Energy-based cost integrated modelling and sustainability assessment of Al-GnP hybrid nanofluid assisted turning of AISI52100 steel
Aqib Mashood Khan et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Manufacturing cost estimation based on the machining process and deep-learning method
Fangwei Ning et al.
JOURNAL OF MANUFACTURING SYSTEMS (2020)
High-speed machining of aluminium alloy using vegetable oil based small quantity lubrication
Balakrushna Guntreddi et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2020)
Lipophilic magnetite nanoparticles coated with stearic acid: A potential green and low cost way to improve thermal stability and tribological properties of fully formulated low viscosity engine oils
Andre Zuin et al.
TRIBOLOGY INTERNATIONAL (2020)
Comprehensive machining analysis to establish cryogenic LN2 and LCO2 as sustainable cooling and lubrication techniques
Prassan Shah et al.
TRIBOLOGY INTERNATIONAL (2020)
Evaluation of turning with different cooling-lubricating techniques in terms of surface integrity and tribologic properties
Radoslaw W. Maruda et al.
TRIBOLOGY INTERNATIONAL (2020)
Critical review on ecological, economical and technological aspects of minimum quantity lubrication towards sustainable machining
Gurpreet Singh et al.
JOURNAL OF CLEANER PRODUCTION (2020)
Sustainability Assessment, Investigations, and Modelling of Slot Milling Characteristics in Eco-Benign Machining of Hardened Steel
Angelos P. Markopoulos et al.
METALS (2020)
Experimental investigation on the performance of MQL drilling of AISI 321 stainless steel using nano-graphene enhanced vegetable-oil-based cutting fluid
Amrit Pal et al.
TRIBOLOGY INTERNATIONAL (2020)
Low-Velocity Impact Behavior of Porous Metal Matrix Composites Produced by Recycling of Bronze and Iron Chips
Omer Sinan Sahin et al.
IRANIAN JOURNAL OF SCIENCE AND TECHNOLOGY-TRANSACTIONS OF MECHANICAL ENGINEERING (2019)
A general framework for sustainability assessment of manufacturing processes
Mohammed H. Saad et al.
ECOLOGICAL INDICATORS (2019)
Multi-Objective Optimization of Energy Consumption and Surface Quality in Nanofluid SQCL Assisted Face Milling
Aqib Mashood Khan et al.
ENERGIES (2019)
Effects of hybrid Al2O3-CNT nanofluids and cryogenic cooling on machining of Ti-6Al-4V
Muhammad Jamil et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N2 assisted turning of Ti-6Al-4V
Mozammel Mia et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Modeling and optimization of sustainable manufacturing process in machining of 17-4 PH stainless steel
P. Sivaiah et al.
MEASUREMENT (2019)
Sustainability in Ultra Precision and Micro Machining: A Review
Frank Schneider et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2019)
Ecological trends in machining as a key factor in sustainable production - A review
G. M. Krolczyk et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Advances in ultra-precision machining of micro-structured functional surfaces and their typical applications
Shaojian Zhang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)
The relationship between lean and environmental performance: Practices and measures
Marcos Dieste et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Enhanced machinability of SiC-reinforced metal-matrix composite with hybrid turning
Wei Bai et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Role of textured tool in improving machining performance: A review
Priya Ranjan et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Hybrid cryogenic MQL for improving tool life in machining of Ti-6Al-4V titanium alloy
Alborz Shokrani et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Influence of minimum quantity lubrication in the surface quality of milled maraging steel
Italo V. Tomaz et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Effect of cutting parameters on tool wear under minimum quantity cooling lubrication (MQCL) conditions
Niancong Liu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Study on modal analysis and chip breaking mechanism of Inconel 718 by ultrasonic vibration-assisted drilling
Shuo Chen et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Experimental comparison of the performance of nanofluids, cryogenic and hybrid cooling in turning of Inconel 625
Cagri Vakkas Yildirim
TRIBOLOGY INTERNATIONAL (2019)
Robust Polymer Nanocomposite Membranes Incorporating Discrete TiO2 Nanotubes for Water Treatment
Najia Mahdi et al.
NANOMATERIALS (2019)
Optimization of cutting conditions using artificial neural networks and the Edgeworth-Pareto method for CNC face-milling operations on high-strength grade-H steel
Adel Taha Abbas et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Thrust force modelling and surface roughness optimization in drilling of AA-7075: FEM and GRA
Nafiz Yasar
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2019)
Operations scheduling for waste minimization: A review
Corentin Le Hesran et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Cutting parameter optimization for machining operations considering carbon emissions
Guanghui Zhou et al.
JOURNAL OF CLEANER PRODUCTION (2019)
Green or lean? A supply chain approach to sustainable performance
Baofeng Huo et al.
JOURNAL OF CLEANER PRODUCTION (2019)
The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045
Amiril Sahab Abdul Sani et al.
TRIBOLOGY INTERNATIONAL (2019)
Recent Advances in the Machining of Titanium Alloys using Minimum Quantity Lubrication (MQL) Based Techniques
Salman Pervaiz et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2019)
Vegetable Oil-Based Lubrication in Machining: Issues and Challenges
M. A. Mahadi et al.
INTERNATIONAL CONFERENCE ON RECENT ADVANCES IN INDUSTRIAL ENGINEERING AND MANUFACTURING (2019)
Multi-objective optimization for energy efficient machining with high productivity and quality for a turning process
Kuldip Singh Sangwan et al.
26TH CIRP CONFERENCE ON LIFE CYCLE ENGINEERING (LCE) (2019)
Vegetable Oil Based Lubricants: Challenges and Prospects
Timothy Yakubu Woma et al.
TRIBOLOGY ONLINE (2019)
Energy conscious cryogenic machining of Ti-6Al-4V titanium alloy
Alborz Shokrani et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2018)
Multi-sensor information fusion for remaining useful life prediction of machining tools by adaptive network based fuzzy inference system
Jun Wu et al.
APPLIED SOFT COMPUTING (2018)
Surface quality and topographic inspection of variable compliance part after precise turning
P. Nieslony et al.
APPLIED SURFACE SCIENCE (2018)
Machining β-titanium alloy under carbon dioxide snow and micro-lubrication: a study on tool deflection, energy consumption, and tool damage
Asif Iqbal et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Real-time cutting tool state recognition approach based on machining features in NC machining process of complex structural parts
Changqing Liu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Arc characteristic evaluation of the double-electrode GTAW process using high current values
Mateus Barancelli Schwedersky et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Performance evaluation of Ti-6Al-4V machining using nano-cutting fluids under minimum quantity lubrication
H. Hegab et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Optimisation of cutting parameters for minimizing carbon emission and maximising cutting quality in turning process
Yusuf Tansel Ic et al.
INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH (2018)
Performance evaluation of vegetable oil based nano cutting fluids in machining using grey relational analysis-A step towards sustainable manufacturing
Padmini Rapeti et al.
JOURNAL OF CLEANER PRODUCTION (2018)
An approach to cleaner production for machining hardened steel using different cooling-lubrication conditions
Mozammel Mia et al.
JOURNAL OF CLEANER PRODUCTION (2018)
On the concurrent optimization of environmental and economic targets for machining
Paolo C. Priarone et al.
JOURNAL OF CLEANER PRODUCTION (2018)
Multi-objective optimization of tool path considering efficiency, energy-saving and carbon-emission for free-form surface milling
Li Li et al.
JOURNAL OF CLEANER PRODUCTION (2018)
An extensive review of the water consumption and cutting fluid based sustainability concerns in the metal cutting sector
Salman Pervaiz et al.
JOURNAL OF CLEANER PRODUCTION (2018)
Effects of duplex jets high-pressure coolant on machining temperature and machinability of Ti-6Al-4V superalloy
Mozammel Mia et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
Parametric and nonparametric description of the surface topography in the dry and MQCL cutting conditions
G. M. Krolczyk et al.
MEASUREMENT (2018)
Recycling of waste Ti machining chips by planetary milling: Generation of Ti powder and development of in situ TiC reinforced Ti-TiC composite powder mixture
S. R. Shial et al.
POWDER TECHNOLOGY (2018)
A machine vision system for micro-milling tool condition monitoring
Yiquan Dai et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2018)
Energy centric selection of machining conditions for minimum cost
Vincent Aizebeoje Balogun et al.
ENERGY (2018)
Mechanical properties and microstructure of composites produced by recycling metal chips
Abdullah Aslan et al.
INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2018)
Wear analysis of PVD-coated twist drills under MQL
Marlon Jose Cardoso et al.
INDUSTRIAL LUBRICATION AND TRIBOLOGY (2018)
Effect of cryogenic coolant on turning performance characteristics during machining of 17-4 PH stainless steel: A comparison with MQL, wet, dry machining
P. Sivaiah et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2018)
Finite Element Modelling of Cutting Forces and Power Consumption in Turning of AISI 420 Martensitic Stainless Steel
Mehmet Erdi Korkmaz et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2018)
High-pressure coolant on flank and rake surfaces of tool in turning of Ti-6Al-4V: investigations on forces, temperature, and chips
Md Awal Khan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Optimization of MQL flow rate for minimum cutting force and surface roughness in end milling of hardened steel (HRC 40)
Mozammel Mia et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Integrated optimization methodology for intelligent machining of inconel 825 and its shop-floor application
S. K. Tamang et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
Energy efficiency of machining operations: A review
Mariyeh Moradnazhad et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2017)
Energy consumption in machining: Classification, prediction, and reduction strategy
G. Y. Zhao et al.
ENERGY (2017)
Analysis of local cutting edge geometry on temperature distribution and surface integrity when dry drilling of aeronautical alloys
G. Le Coz et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Minimization of turning time for high-strength steel with a given surface roughness using the Edgeworth-Pareto optimization method
A. T. Abbas et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Application of cutting fluids in machining of titanium alloys-a review
Rukmini Srikant Revuru et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Surface integrity and tool life when turning of Ti-6Al-4V with coolant applied by different methods
Rosemar B. Da Silva et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Recycling of contaminated metallic chip based on eco-efficiency and eco-effectiveness approaches
Luisa Simon et al.
JOURNAL OF CLEANER PRODUCTION (2017)
Dry machining: A step towards sustainable machining - Challenges and future directions
Gyanendra Singh Goindi et al.
JOURNAL OF CLEANER PRODUCTION (2017)
On the CO2 characterization in incremental forming of roll bonded laminates
Khalid A. Al-Ghamdi et al.
JOURNAL OF CLEANER PRODUCTION (2017)
Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
G. M. Krolczyk et al.
JOURNAL OF CLEANER PRODUCTION (2017)
Finite element modeling of tool stresses on ceramic tools in hard turning
M. Gunay et al.
MECHANIKA (2017)
Performance of cutting tools with dimple textured surfaces: A comparative study of different texture patterns
Tatsuya Sugihara et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2017)
Review of solid state recycling of aluminum chips
Bingbing Wan et al.
RESOURCES CONSERVATION AND RECYCLING (2017)
Tool wear characterizations in finish turning of AISI 1045 carbon steel for MQCL conditions
Radoslaw W. Maruda et al.
WEAR (2017)
Eco-Friendly Technology for Recycling of Cutting Fluids and Metal Chips: A Review
Choon-Man Lee et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY (2017)
Flank wear characteristics of WC-Co tools when turning Alloy 718 with high-pressure coolant supply
Philipp Hoier et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Hybrid cooling and lubricating technology for CNC milling of Inconel 718 nickel alloy
Alborz Shokrani et al.
27TH INTERNATIONAL CONFERENCE ON FLEXIBLE AUTOMATION AND INTELLIGENT MANUFACTURING, FAIM2017 (2017)
Technical, Economic and Environmental Review of the Lubrication/Cooling Systems used in Machining Processes
E. Benedicto et al.
ADVANCES IN MATERIAL & PROCESSING TECHNOLOGIES CONFERENCE (2017)
The water-energy nexus in manufacturing systems: Framework and systematic improvement approach
Sebastian Thiede et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2017)
Recycling of plastic solid waste: A state of art review and future applications
Narinder Singh et al.
COMPOSITES PART B-ENGINEERING (2017)
Optimization studies in high speed turning of Ti-6Al-4V
Grynal D'Mello et al.
APPLIED SOFT COMPUTING (2017)
Optimization of multi-tool machining processes with simultaneous action
Ryspek Usubamatov et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
An integrated model for predicting the specific energy consumption of manufacturing processes
Jun Xie et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Optimization of cutting parameters to minimize energy consumption during turning of AISI 1018 steel at constant material removal rate using robust design
Carmita Camposeco-Negrete et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Cryogenic manufacturing processes
I. S. Jawahir et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)
An experimental investigation on effect of minimum quantity cooling lubrication (MQCL) in machining titanium alloy (Ti6Al4V)
Salman Pervaiz et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Optimization of energy consumption response parameters for turning operation using Taguchi method
Paramjit Singh Bilga et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Effects of Minimum Quantity Lubrication (MQL) in machining processes using conventional and nanofluid based cutting fluids: A comprehensive review
Anuj Kumar Sharma et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Recent developments in sustainable manufacturing of gears: a review
Kapil Gupta et al.
JOURNAL OF CLEANER PRODUCTION (2016)
Energy consumption model and energy efficiency of machine tools: a comprehensive literature review
Lirong Zhou et al.
JOURNAL OF CLEANER PRODUCTION (2016)
A Review of Sustainable Machining Engineering: Optimization Process Through Triple Bottom Line
Maria Estela Peralta Alvarez et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2016)
Prediction of surface residual stress after end milling based on cutting force and temperature
Yuan Ma et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
A modified mussel-inspired method to fabricate TiO2 decorated superhydrophilic PVDF membrane for oil/water separation
Heng Shi et al.
JOURNAL OF MEMBRANE SCIENCE (2016)
Surface morphology analysis of Duplex Stainless Steel (DSS) in Clean Production using the Power Spectral Density
G. M. Krolczyk et al.
MEASUREMENT (2016)
Prediction of surface roughness in hard turning under high pressure coolant using Artificial Neural Network
Mozammel Mia et al.
MEASUREMENT (2016)
Environmental impacts and hazards associated with metal working fluids and recent advances in the sustainable systems: A review
M. S. Najiha et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)
The influence of the cooling conditions on the cutting tool wear and the chip formation mechanism
Radoslaw W. Maruda et al.
JOURNAL OF MANUFACTURING PROCESSES (2016)
Solid-state recycling of light metals: A review
Shazarel Shamsudin et al.
ADVANCES IN MECHANICAL ENGINEERING (2016)
Experimental investigation and modelling of surface roughness and resultant cutting force in hard turning of AISI H13 Steel
M. Boy et al.
20TH INNOVATIVE MANUFACTURING ENGINEERING AND ENERGY CONFERENCE (IMANEE 2016) (2016)
Minimum Quantity Lubrication: Influence of the oil nature on surface integrity
Sana Werda et al.
3RD CIRP CONFERENCE ON SURFACE INTEGRITY (2016)
Determination of tool life and research wear during duplex stainless steel turning
G. M. Krolczyk et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2015)
Effects of cutting parameters on dry machining Ti-6Al-4V alloy with ultra-hard tools
F. J. Sun et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
A sustainability comparison between conventional and high-speed machining
Khalid A. Al-Ghamdi et al.
JOURNAL OF CLEANER PRODUCTION (2015)
High speed tandem gas tungsten arc welding process of thin stainless steel plate
Guoliang Qin et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Correlation Between Cutting Data Selection and Chip Form in Stainless Steel Turning
Bogdan Slodki et al.
MACHINING SCIENCE AND TECHNOLOGY (2015)
Influence of High-Pressure Coolant Assistance on the Machinability of the Titanium Alloy Ti555-3
Tarek Braham-Bouchnak et al.
MACHINING SCIENCE AND TECHNOLOGY (2015)
Towards greener machine tools - A review on energy saving strategies and technologies
Hae-Sung Yoon et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2015)
A rule-based system for trade-off among energy consumption, tool life, and productivity in machining process
Asif Iqbal et al.
JOURNAL OF INTELLIGENT MANUFACTURING (2015)
Progress of Nanofluid Application in Machining: A Review
Anuj Kumar Sharma et al.
MATERIALS AND MANUFACTURING PROCESSES (2015)
Waste elimination for manufacturing sustainability
Sherif Mostafa et al.
2ND INTERNATIONAL MATERIALS, INDUSTRIAL, AND MANUFACTURING ENGINEERING CONFERENCE, MIMEC2015 (2015)
Simultaneous optimization of multi performance characteristics in dry turning of Inconel 718 using NSGA-II
B. Satyanarayana et al.
MATERIALS TODAY-PROCEEDINGS (2015)
Advancing Environmentally Conscious Machining
Yogie Rinaldy Ginting et al.
12TH GLOBAL CONFERENCE ON SUSTAINABLE MANUFACTURING - EMERGING POTENTIALS (2015)
The relationship between lean operations and sustainable operations
Niall Piercy et al.
INTERNATIONAL JOURNAL OF OPERATIONS & PRODUCTION MANAGEMENT (2015)
Energy efficiency techniques in machining process: a review
Zhang Yingjie
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Advantages of milling and drilling Ti-6Al-4V components with high-pressure coolant
M. J. Bermingham et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Energy-efficient machining systems: a critical review
Tao Peng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)
Investigation of effects of dry and near dry machining on AISI D2 steel using vegetable oil
Jagdeep Sharma et al.
JOURNAL OF CLEANER PRODUCTION (2014)
Environmental friendly cutting fluids and cooling techniques in machining: a review
Sujan Debnath et al.
JOURNAL OF CLEANER PRODUCTION (2014)
Microhardness and Surface Integrity in Turning Process of Duplex Stainless Steel (DSS) for Different Cutting Conditions
G. Krolczyk et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Monitoring and processing signal applied in machining processes - A review
C. H. Lauro et al.
MEASUREMENT (2014)
Multiple Process Parameter Optimization of WEDM on AISI304 Using Utility Approach
BijoMathew et al.
INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014) (2014)
Minimum Quantity Lubrication (MQL) in Automotive Powertrain Machining
Bruce L. Tai et al.
6TH CIRP INTERNATIONAL CONFERENCE ON HIGH PERFORMANCE CUTTING (HPC2014) (2014)
Machining optimization using swarm intelligence in titanium (6Al 4V) alloy
Indira G. Escamilla-Salazar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Green as the new Lean: how to use Lean practices as a catalyst to greening your supply chain
Christina Maria Dues et al.
JOURNAL OF CLEANER PRODUCTION (2013)
Tool life and wear mechanisms in high speed machining of Ti-6Al-4V alloy with PCD tools under various coolant pressures
Rosemar B. da Silva et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Process parameter optimization during EDM of AISI 316 LN stainless steel by using fuzzy based multi-objective PSO
Arindam Majumder
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2013)
Quantifying the water inventory of machining processes
Fu Zhao et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)
Towards energy and resource efficient manufacturing: A processes and systems approach
Joost R. Duflou et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2012)
Evolutionary techniques in optimizing machining parameters: Review and recent applications (2007-2011)
Norfadzlan Yusup et al.
EXPERT SYSTEMS WITH APPLICATIONS (2012)
Intelligent optimization and selection of machining parameters in finish turning and facing of Inconel 718
J. S. Senthilkumaar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Determination of optimum parameters for multi-performance characteristics in turning by using grey relational analysis
L. B. Abhang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Optimization of Machining Parameters in Turning of Titanium (Grade-5) Alloy Using Response Surface Methodology
S. R. Chauhan et al.
MATERIALS AND MANUFACTURING PROCESSES (2012)
Productivity Improvement in Tooling Manufacture through High Speed 5 Axis Machining
D. Dimitrov et al.
FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)
Initial analysis of cost, energy and carbon dioxide emissions in single point incremental forming - producing an aluminium hat
K. Branker et al.
INTERNATIONAL JOURNAL OF SUSTAINABLE ENGINEERING (2012)
Calculation of optimum cutting parameters based on minimum energy footprint
P. T. Mativenga et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)
A study on energy efficiency improvement for machine tools
M. Mori et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)
Unit process energy consumption models for material removal processes
S. Kara et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)
Tools and techniques for enabling sustainability through lean initiatives
S. Vinodh et al.
CLEAN TECHNOLOGIES AND ENVIRONMENTAL POLICY (2011)
Experimental studies and optimization of process parameters for burrs in dry drilling of stacked metal materials
Shusheng Bi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Machining induced surface integrity in titanium and nickel alloys: A review
Durul Ulutan et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2011)
Environmental comparison of MESO-CLAD® process and conventional machining implementing life cycle assessment
Nicolas Serres et al.
JOURNAL OF CLEANER PRODUCTION (2011)
Tribological characteristics of electroless Ni-B coating and optimization of coating parameters using Taguchi based grey relational analysis
Suman Kalyan Das et al.
MATERIALS & DESIGN (2011)
Laser stripping of TiAlN coating to facilitate reuse of cutting tools
S. Marimuthu et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2011)
A review on energy saving strategies in industrial sector
E. A. Abdelaziz et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2011)
A review on applications and challenges of nanofluids
R. Saidur et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2011)
Optimization of multi-task turning operations under minimal tool waste consideration
Yi-Chi Wang et al.
ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2011)
Monitoring online cutting tool wear using low-cost technique and user-friendly GUI
J. A. Ghani et al.
WEAR (2011)
Transitioning to sustainable production - part II: evaluation of sustainable machining technologies
Franci Pusavec et al.
JOURNAL OF CLEANER PRODUCTION (2010)
Transitioning to sustainable production - Part I: application on machining technologies
Frand Pusavec et al.
JOURNAL OF CLEANER PRODUCTION (2010)
Sustainable machining: selection of optimum turning conditions based on minimum energy considerations
M. F. Rajemi et al.
JOURNAL OF CLEANER PRODUCTION (2010)
Surface roughness and cutting force prediction in MQL and wet turning process of AISI 1045 using design of experiments
Young Kug Hwang et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2010)
Optimisation of machining parameters for hard machining: grey relational theory approach and ANOVA
Bala Murugan Gopalsamy et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
Cooling techniques for improved productivity in turning
Vishal S. Sharma et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
High Productivity Rough Turning of Ti-6Al-4V Alloy, with Flood and High-Pressure Cooling
E. O. Ezugwu et al.
TRIBOLOGY TRANSACTIONS (2009)
Carbon emissions and CESTM in manufacturing
J. Jeswiet et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2008)
Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718
R. S. Pawade et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2008)
Lubricant base stock potential of chemically modified vegetable oils
Sevim Z. Erhan et al.
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY (2008)
Fuzzy modeling and analysis of machining parameters in machining titanium alloy
S. Ramesh et al.
MATERIALS AND MANUFACTURING PROCESSES (2008)
Surface roughness analysis in machining of titanium alloy
S. Ramesh et al.
MATERIALS AND MANUFACTURING PROCESSES (2008)
Study on the treatment of waste metal cutting fluids using electrocoagulation
M. Kobya et al.
SEPARATION AND PURIFICATION TECHNOLOGY (2008)
Methods for polyurethane and polyurethane composites, recycling and recovery: A review
Khalid Mahmood Zia et al.
REACTIVE & FUNCTIONAL POLYMERS (2007)
Use of selected waste materials in concrete mixes
Malek Batayneh et al.
WASTE MANAGEMENT (2007)
Modeling and analysis for surface roughness in machining glass fibre reinforced plastics using response surface methodology
K. Palanikumar
MATERIALS & DESIGN (2007)
A simple two-phase route to silver nanoparticles/polyaniline structures
Marcela M. Oliveira et al.
JOURNAL OF PHYSICAL CHEMISTRY B (2006)
Taguchi and Gauss elimination method: A dual response approach for parametric optimization of CNC wire cut EDM of PRAISiCMMC
A Manna et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2006)
Optimization of machining techniques - A retrospective and literature review
A Aggarwal et al.
SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES (2005)
Treatment of spent metalworking fluids
C Cheng et al.
WATER RESEARCH (2005)
Application of Taguchi and response surface methodologies for geometric error in surface grinding process
JS Kwak
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2005)
Gas attachment of oil droplets for gas flotation for oily wastewater cleanup
R Moosai et al.
SEPARATION AND PURIFICATION TECHNOLOGY (2003)
Overview of flotation as a wastewater treatment technique
J Rubio et al.
MINERALS ENGINEERING (2002)
Friction and cutting forces in cryogenic machining of Ti-6Al-4V
SY Hong et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2001)
Economical and ecological cryogenic machining
SY Hong
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2001)
Computer-munching microbes: metal leaching from electronic scrap by bacteria and fungi
H Brandl et al.
HYDROMETALLURGY (2001)
Dry machining: Machining of the future
PS Sreejith et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)