相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。The Study on Microstructural Evolution During Post-processing of Additively Manufactured Ti64
Bryan Naab et al.
TMS 2022 151ST ANNUAL MEETING & EXHIBITION SUPPLEMENTAL PROCEEDINGS (2022)
Mechanism of stress relaxation and phase transformation in additively manufactured Ti-6Al-4V via in situ high temperature XRD and TEM analyses
F. R. Kaschel et al.
ACTA MATERIALIA (2020)
Experimental study on additive/subtractive hybrid manufacturing of 6511 steel: process optimization and machining characteristics
Qian Bai et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Effects of laser power on geometry, microstructure and mechanical properties of printed Ti-6Al-4V parts
F. R. Kaschel et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography
Wei Liu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Effects of internal porosity and crystallographic texture on Charpy absorbed energy of electron beam melting titanium alloy (Ti-6Al-4V)
Nikolas Hrabe et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Influence of hot isostatic pressing on mechanical response of as-built SLM titanium alloy
M. Roudnicka et al.
2ND INTERNATIONAL CONFERENCE ON MATERIAL STRENGTH AND APPLIED MECHANICS (2019)
Effect of Surface Roughness on Fatigue Strength of Ti-6Al-4V Alloy Manufactured by Additive Manufacturing
Masanori Nakatani et al.
FATIGUE DESIGN 2019, INTERNATIONAL CONFERENCE ON FATIGUE DESIGN, 8TH EDITION (2019)
Selective Laser Melting Produced Ti-6Al-4V: Post-Process Heat Treatments to Achieve Superior Tensile Properties
Gerrit M. Ter Haar et al.
MATERIALS (2018)
Research on Selective Laser Melting of Ti6Al4V: Surface Morphologies, Optimized Processing Zone, and Ductility Improvement Mechanism
Di Wang et al.
METALS (2018)
Mechanism of porosity formation and influence on mechanical properties in selective laser melting of Ti-6Al-4V parts
Jonathan Stef et al.
MATERIALS & DESIGN (2018)
Surface roughness of Ti-6A1-4V parts obtained by SLM and EBM: Effect on the High Cycle Fatigue life
Bastien Vayssette et al.
7TH INTERNATIONAL CONFERENCE ON FATIGUE DESIGN, FATIGUE DESIGN 2017 (2018)
Fatigue crack growth mechanisms at the microstructure scale in as-fabricated and heat treated Ti-6A1-4V ELI manufactured by electron beam melting (EBM)
Haize Galarraga et al.
ENGINEERING FRACTURE MECHANICS (2017)
Fatigue and fracture behaviour of laser powder bed fusion stainless steel 316L: Influence of processing parameters
Meng Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
S. Tammas-Williams et al.
SCIENTIFIC REPORTS (2017)
Microstructure, static properties, and fatigue crack growth mechanisms in Ti-6Al-4V fabricated by additive manufacturing: LENS and EBM
Yuwei Zhai et al.
ENGINEERING FAILURE ANALYSIS (2016)
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Todd M. Mower et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
The Nature of Tensile Ductility as Controlled by Extreme-Sized Pores in Powder Metallurgy Ti-6Al-4V Alloy
P. Kumar et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting
Samuel Tammas-Williams et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)
Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties
M. Qian et al.
MRS BULLETIN (2016)
Comparison of the microstructures and mechanical properties of Ti-6Al-4V fabricated by selective laser melting and electron beam melting
Xiaoli Zhao et al.
MATERIALS & DESIGN (2016)
Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting
Galina Kasperovich et al.
MATERIALS & DESIGN (2016)
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Galina Kasperovich et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Fatigue performance evaluation of selective laser melted Ti-6Al-4V
P. Edwards et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Electron Beam Additive Manufacturing of Titanium Components: Properties and Performance
P. Edwards et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2013)
Microstructures and Mechanical Properties of Ti6Al4V Parts Fabricated by Selective Laser Melting and Electron Beam Melting
H. K. Rafi et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2013)
Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti-6Al-4V
Chunlei Qiu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties
Bey Vrancken et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2012)
X-ray analysis of ZnO nanoparticles by Williamson-Hall and size-strain plot methods
A. Khorsand Zak et al.
SOLID STATE SCIENCES (2011)
Towards a physics-based description of fatigue variability behavior in probabilistic life-prediction
S. K. Jha et al.
ENGINEERING FRACTURE MECHANICS (2009)
分享论文
