4.7 Article

Modeling the micromechanical behaviors of Zircaloy-2 alloy under large deformation

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Engineering, Mechanical

A non-local crystal plasticity constitutive model for hexagonal close-packed polycrystals

Omid Sedaghat et al.

Summary: A strain gradient crystal plasticity finite element model is developed to study the evolution of internal and localized elastic strains in hexagonal close-packed polycrystals. The model results are compared with in-situ neutron diffraction experiments for alpha-zirconium specimens, showing that the non-local model provides a better estimation of localized stresses in regions with sharp strain gradients.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Metallurgy & Metallurgical Engineering

Unloading behaviors of the rare-earth magnesium alloy ZE10 sheet

Weiqin Tang et al.

Summary: The unloading behaviors of the rare-earth magnesium alloy ZE10 sheet were studied using mechanical tests and crystal plasticity modeling. The study found significant anisotropy and loading path dependency in the unloading behaviors of ZE10 sheets. Inelastic strains varied under different loading conditions, with basal slip, twinning, and de-twinning being responsible for the behaviors.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Article Materials Science, Multidisciplinary

Numerical analysis of twin-precipitate interactions in magnesium alloys

Filip Siska et al.

Summary: This paper investigates the interactions between {10 (1) over bar2} ten sile twin and precipitates aligned along basal planes in magnesium alloys. The results show that precipitates influence the shear stress necessary to accommodate twins, and the thickness of precipitates plays a crucial role in twin thickening and propagation.

ACTA MATERIALIA (2021)

Article Engineering, Mechanical

Numerical study of deformation behavior of rolled AZ31B plate under cyclic loading in different material orientations based on the EVPSC-TDT model

F. H. Wang et al.

Summary: The study utilized the EVPSC-TDT model to simulate the stabilized stress-strain hysteresis loops of rolled AZ31B plate in different material orientations under cyclic loading, showing good agreement with experimental data. Parameters influencing plastic response were investigated and the effect of initial CRSS on twinning and detwinning during reverse loading was studied. The discrepancies between simulations and experiments suggest the need for further investigation into microstructure-related properties and internal tensile stresses of twinned grains.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Engineering, Mechanical

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Xiaodan Zhang et al.

Summary: In this study, an elastic visco-plastic self-consistent model with twinning and detwinning scheme, along with a torsion specific finite element approach, is used to simulate the deformation behavior of magnesium alloy solid rod with different initial textures. It was found that the deformation mechanisms, stress-strain response, Swift effect, and deformation texture vary significantly with different initial textures and loading paths, highlighting the importance of understanding the influence of these factors on mechanical properties.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Article Engineering, Mechanical

The effects of heat treatment on the response of WE43 Mg alloy: crystal plasticity finite element simulation and SEM-DIC experiment

Sriram Ganesan et al.

Summary: This study investigates the effects of heat treatment on the mechanical response of a WE43 Mg alloy using an integrated framework of SEM-DIC experiment and CPFE simulation, focusing on local displacement and strain. By evaluating the CPFE framework with results from SEM-DIC experiment, the effects of heat treatment were analyzed using CRSS and relative slip activity. The study also addresses the contributions of different strengthening mechanisms on CRSS in WE43 Mg alloy.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Mechanics

Effect of uniaxial loading direction on mechanical responses and texture evolution in cold pilgered Zircaloy-4 tube: Experiments and modeling

Siying Deng et al.

Summary: The mechanical responses of cold pilgered Zircaloy-4 (Zr-4) tubes were measured under different uniaxial loading directions, revealing anisotropic yield stress and strain hardening behavior. The variations in activation of deformation mechanisms predicted by the Schmid factor distribution and visco-plastic self-consistent (VPSC) model explain the complex mechanical behavior observed. Additionally, texture evolution under different loading directions were disclosed based on VPSC method, showing significant changes in the activity of deformation mechanisms with different uniaxial loading directions.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2021)

Article Engineering, Mechanical

A three-dimensional mechanistic study of the drivers of classical twin nucleation and variant selection in Mg alloys: A mesoscale modelling and experimental study

Chaitanya Paramatmuni et al.

Summary: This work investigates twin inception in a 3D reconstructed microstructure, finding that stored energy density is a key factor in identifying the nucleation site in Mg alloy AZ31. The experimentally observed twin variant is driven by local twin resolved shear stress at the predicted nucleation site.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Mechanics

Effect of twinning on the yield surface shape of Mg alloy plates under in-plane biaxial loading

H. Qiao et al.

Summary: The EVPSC-TDT model was used to investigate the yield behavior of a strongly basal textured Mg alloy plate under biaxial loading, with material parameters calibrated according to experimental uniaxial tension and compression tests. The predicted yield surface under various biaxial loadings matched well with experimental data, with the shape changes explained by activated deformation modes. Twining behaviors and their effects on the yield surface shape were also discussed, along with the influence of initial texture on the shape of the yield surface of Mg alloy plates.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2021)

Article Materials Science, Multidisciplinary

A microstructure-based modeling approach to predict the mechanical properties of Zr alloy with hydride precipitates

Shank S. Kulkarni et al.

Summary: This study presents a microstructure-based finite element model to predict the stress-strain response of Zircaloy containing hydrides, considering the effect of hydride formation on mechanical properties. Parametric study and experimental validation show that the volume fraction, orientation, and lamellae width of the hydride phase significantly influence the overall material properties.

COMPUTATIONAL MATERIALS SCIENCE (2021)

Article Engineering, Mechanical

A crystal plasticity finite element model embedding strain-rate sensitivities inherent to deformation mechanisms: Application to alloy AZ31

William G. Feather et al.

Summary: This paper introduces a numerical method to embed any value of the power-law exponent in a crystal plasticity finite element model, reflecting the true material strain-rate sensitivity, and successfully applies it to predict the complex strain-rate sensitive response of AZ31 Mg alloy. Calculations show that the model captures the phenomena related to the effect of changing applied strain-rate on mechanical response.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Engineering, Mechanical

Grain-size effect on the deformation of Mg-3Al-3Sn alloy: Experiments and elastic-viscoplastic self-consistent modeling

Gaoming Zhu et al.

Summary: Grain refinement in Mg-3Al-3Sn alloy can increase yield strength while decreasing strain hardening exponent, with different slip modes being affected by the grain size. A model taking grain size into account successfully predicts the deformation behavior, showing that prismatic slip is the dominant mode in this alloy and coarse-grained samples exhibit higher dislocation nucleation coefficient due to twin formation.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Article Materials Science, Multidisciplinary

Effects of temperature and alloying content on the phase transformation and {10(1)over-bar1} twinning in Zr during rolling

Xinglong An et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Article Materials Science, Multidisciplinary

Characterization and modeling of {10(1)over-bar2} twin banding in magnesium

YubRaj Paudel et al.

ACTA MATERIALIA (2020)

Article Engineering, Mechanical

Modeling of 3D plastic anisotropy and asymmetry of extruded magnesium alloy and its applications in three-point bending

Fei-Fan Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Article Engineering, Mechanical

Strain hardening, twinning and texture evolution in magnesium alloy using the all twin variant polycrystal modelling approach

Sudeep K. Sahoo et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Article Materials Science, Multidisciplinary

Crystal plasticity modeling and neutron diffraction measurements of a magnesium AZ31B plate: Effects of plastic anisotropy and surrounding grains

Huamiao Wang et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2020)

Article Nanoscience & Nanotechnology

On plastic anisotropy and deformation history-driven anelasticity of an extruded magnesium alloy

Huai Wang et al.

SCRIPTA MATERIALIA (2020)

Article Engineering, Mechanical

Multiscale modeling of twinning and detwinning behavior of HCP polycrystals

Mohammadreza Yaghoobi et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Article Materials Science, Multidisciplinary

Twinning behaviors and grain refinement mechanisms during friction stir processing of Zr alloy

Shuo Li et al.

MATERIALS CHARACTERIZATION (2020)

Article Engineering, Mechanical

Forming limits of magnesium alloy AZ31B sheet at elevated temperatures

Zihan Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Article Materials Science, Multidisciplinary

On the nucleation of deformation twins at the early stages of plasticity

Hamidreza Abdolvand et al.

ACTA MATERIALIA (2020)

Article Materials Science, Multidisciplinary

Deformation mechanisms of zirconium alloys under biaxial tension at room temperature

Gang Chen et al.

MATERIALS LETTERS (2020)

Article Nanoscience & Nanotechnology

Pre-deformation enhanced {10-12} twinning in a zirconium alloy

Xin Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Article Metallurgy & Metallurgical Engineering

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Xiaoqian Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Article Engineering, Mechanical

Crystallographic orientation sensitive measurement of strain rate sensitivity in Zircaloy-2 via synchrotron X-ray diffraction

Travis Skippon et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2019)

Article Engineering, Mechanical

Twinning and detwinning behaviors of commercially pure titanium sheets

Chao Ma et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2019)

Article Nanoscience & Nanotechnology

Detwinning behavior in commercial pure zirconium during orthogonal re-compression after pre-compression and annealing

Xin Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Article Nanoscience & Nanotechnology

Numerical study of large strain behavior of OFHC copper: The role of latent hardening

X. Q. Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Article Materials Science, Multidisciplinary

Strain-Path Dependence of {10(1)over-bar2} Twinning in a Rolled Mg-3Al-1Zn Alloy: Influence of Twinning Model

Lingyu Zhao et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)

Article Engineering, Mechanical

Strain rate sensitivities of deformation mechanisms in magnesium alloys

Huamiao Wang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2018)

Article Chemistry, Physical

Effect of pre-annealing deformation on thermally activated twin boundary migration in a zirconium alloy

Weijun He et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Article Nanoscience & Nanotechnology

Grain size effect on the thermally activated twin boundary migration in a zirconium alloy

Weijun He et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Article Nanoscience & Nanotechnology

Effect of temperature on the selection of deformation modes in Zircaloy-4

G. Bharat Reddy et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Article Chemistry, Physical

Modeling of {10-12}-{10-12} secondary twinning in pre-compressed Mg alloy AZ31

H. Qiao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Article Materials Science, Multidisciplinary

Microstructural and textural characterization of Zircaloy-4 processed by rolling at different temperatures

Devasri Fuloria et al.

MATERIALS CHARACTERIZATION (2017)

Article Nanoscience & Nanotechnology

Stacking faults observed in {10(1)over-bar2} extension twins in a compressed high Sn content Zr alloy

Hongbing Yu et al.

SCRIPTA MATERIALIA (2017)

Article Materials Science, Multidisciplinary

Temperature dependence of work hardening in sparsely twinning zirconium

Jaiveer Singh et al.

ACTA MATERIALIA (2017)

Article Materials Science, Multidisciplinary

Effect of local stress fields on twin characteristics in HCP metals

M. Arul Kumar et al.

ACTA MATERIALIA (2016)

Article Mechanics

Study of large strain behavior of OFHC copper: The role of polycrystal plasticity model

X. Q. Guo et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2016)

Article Materials Science, Multidisciplinary

Hydride formation on deformation twin in zirconium alloy

Ju-Seong Kim et al.

JOURNAL OF NUCLEAR MATERIALS (2016)

Article Nanoscience & Nanotechnology

The effect of loading direction and Sn alloying on the deformation modes of Zr: An in-situ neutron diffraction study

K. V. Mani Krishna et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Article Nanoscience & Nanotechnology

A new empirical equation for termination of twinning in magnesium alloys

H. Qiao et al.

SCRIPTA MATERIALIA (2016)

Article Materials Science, Multidisciplinary

Strain rate and temperature effects on the selection of primary and secondary slip and twinning systems in HCP Zr

Marko Knezevic et al.

ACTA MATERIALIA (2015)

Article Materials Science, Multidisciplinary

Modelling the role of slips and twins in magnesium alloys under cyclic shear

H. Wang et al.

COMPUTATIONAL MATERIALS SCIENCE (2015)

Article Engineering, Mechanical

Modeling twinning and detwinning behavior of Mg alloy ZK60A during monotonic and cyclic loading

H. Qiao et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2015)

Article Mechanics

On twinning and anisotropy in rolled Mg alloy AZ31 under uniaxial compression

X. Q. Guo et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2015)

Article Mechanics

Evaluation of elastic-viscoplastic self-consistent polycrystal plasticity models for zirconium alloys

H. Qiao et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2015)

Article Materials Science, Multidisciplinary

Deformation Twinning in Zirconium: Direct Experimental Observations and Polycrystal Plasticity Predictions

Jaiveer Singh et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)

Article Metallurgy & Metallurgical Engineering

Study of Lattice Strain Evolution in Stainless Steel Under Tension: The Role of Self-Consistent Plasticity Model

X. Q. Guo et al.

STEEL RESEARCH INTERNATIONAL (2015)

Article Materials Science, Multidisciplinary

Observations of the Atomic Structure of Tensile and Compressive Twin Boundaries and Twin-Twin Interactions in Zirconium

Benjamin M. Morrow et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)

Article Nanoscience & Nanotechnology

Effect of strain rate on twinning in a Zr alloy

Rajeev Kapoor et al.

SCRIPTA MATERIALIA (2014)

Article Engineering, Mechanical

Modeling inelastic behavior of magnesium alloys during cyclic loading-unloading

H. Wang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Article Engineering, Mechanical

A crystal plasticity model for hexagonal close packed (HCP) crystals including twinning and de-twinning mechanisms

H. Wang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Article Nanoscience & Nanotechnology

Load partitioning and evidence of deformation twinning in dual-phase fine-grained Zr-2.5%Nb alloy

O. Muransky et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

Article Materials Science, Multidisciplinary

Temperature Dependence of the Activity of Deformation Modes in an HCP Zirconium Alloy

Fei Long et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)

Article Nanoscience & Nanotechnology

On the Swift effect and twinning in a rolled magnesium alloy under free-end torsion

X. Q. Guo et al.

SCRIPTA MATERIALIA (2013)

Article Materials Science, Multidisciplinary

Anomalous Basal Slip Activity in Zirconium under High-strain Deformation

Marko Knezevic et al.

MATERIALS RESEARCH LETTERS (2013)

Article Materials Science, Multidisciplinary

Influence of texture and test velocity on the dynamic, high-strain, tensile behavior of zirconium

J. P. Escobedo et al.

ACTA MATERIALIA (2012)

Article Nanoscience & Nanotechnology

A constitutive model of twinning and detwinning for hexagonal close packed polycrystals

H. Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Article Engineering, Mechanical

Incorporation of twinning into a crystal plasticity finite element model: Evolution of lattice strains and texture in Zircaloy-2

Hamidreza Abdolvand et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2011)

Article Materials Science, Multidisciplinary

Role of {10-12} twinning characteristics in the deformation behavior of a polycrystalline magnesium alloy

Seong-Gu Hong et al.

ACTA MATERIALIA (2010)

Article Materials Science, Multidisciplinary

A finite strain elastic-viscoplastic self-consistent model for polycrystalline materials

H. Wang et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2010)

Article Materials Science, Multidisciplinary

Statistical analyses of deformation twinning in magnesium

I. J. Beyerlein et al.

PHILOSOPHICAL MAGAZINE (2010)

Article Materials Science, Multidisciplinary

Plastic flow anisotropy of pure zirconium after severe plastic deformation at room temperature

G. G. Yapici et al.

ACTA MATERIALIA (2009)

Article Materials Science, Multidisciplinary

Nucleation and growth of twins in Zr: A statistical study

L. Capolungo et al.

ACTA MATERIALIA (2009)

Article Engineering, Mechanical

Quantitative analysis of deformation twinning in zirconium

Rodney J. McCabe et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2009)

Article Materials Science, Multidisciplinary

Modeling texture evolution during uni-axial deformation of Zircaloy-2

F. Xu et al.

JOURNAL OF NUCLEAR MATERIALS (2009)

Article Materials Science, Multidisciplinary

Modeling lattice strain evolution during uniaxial deformation of textured Zircaloy-2

F. Xu et al.

ACTA MATERIALIA (2008)

Article Materials Science, Multidisciplinary

Evidence for basal ⟨a⟩-slip in Zircaloy-2 at room temperature from polycrystalline modeling

F. Xu et al.

JOURNAL OF NUCLEAR MATERIALS (2008)

Article Nanoscience & Nanotechnology

A finite element model of deformation twinning in zirconium

Richard Y. Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Article Nanoscience & Nanotechnology

Development of internal strains in textured Zircaloy-2 during uni-axial deformation

F. Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Article Physics, Multidisciplinary

Universal elastic anisotropy index

Shivakumar I. Ranganathan et al.

PHYSICAL REVIEW LETTERS (2008)

Review Nuclear Science & Technology

Texture development and anisotropic deformation of zircaloys

KL Murty et al.

PROGRESS IN NUCLEAR ENERGY (2006)

Article Materials Science, Multidisciplinary

Texture dependent plastic behavior of Zr 702 at large strain

O Castelnau et al.

JOURNAL OF NUCLEAR MATERIALS (2001)

Article Nanoscience & Nanotechnology

Microstructure and texture evolution during the annealing of a lamination steel

C Oldani et al.

SCRIPTA MATERIALIA (2000)