☆ 4.7 Article

Precipitation phase and twins strengthening behaviors of as-cast non-equiatomic CoCrFeNiMo high entropy alloys

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Microstructure and microhardness of dual-phase high-entropy alloy by high-pressure torsion: Twins and stacking faults in FCC and dislocations in BCC

Payam Edalati et al.

Summary: Dual-phase HEAs have attracted significant attention due to their promising mechanical properties, and experimental investigation on the AlFeCoNiCu alloy reveals diverse microstructural evolution behaviors of the two phases during plastic deformation, leading to a high microhardness of 495 Hv under high-pressure torsion.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Synergistic effect of Nb and Mo alloying on the microstructure and mechanical properties of CoCrFeNi high entropy alloy

Rui Fan et al.

Summary: Through alloying with Nb and Mo, a new type of Laves phase with hexagonal close-packed structure was formed, and a fine lamellar structure Laves phase was obtained by adjusting the ratio of Nb and Mo, leading to enhanced strength and ductility of the CoCrFeNi alloy system.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Synergistic strengthening of heterogeneous structures and dual-morphology nano-precipitates in Co1.5CrNi1.5Al0.2Ti0.1V0.1 medium-entropy alloy

Xiaofeng Fan et al.

Summary: This study presents the design of a novel non-equiatomic medium-entropy alloy with heterogeneous grain structures and dual-morphology nano-precipitates. The material exhibits high yield strength and ductility, mainly attributed to precipitation strengthening and hetero-deformation induced strengthening.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Significant lattice-distortion effect on compressive deformation in Mo-added CoCrFeNi-based high-entropy alloys

Jiaxiang Li et al.

Summary: The study compared the deformation behaviors of different Mo content HEAs and found that lattice distortion is a key factor affecting the deformation behavior of HEAs, with high-Mo HEAs exhibiting a higher strain-hardening rate.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Crack-resistant σ/FCC interfaces in the Fe40Mn40Co10Cr10 high entropy alloy with the dispersed σ-phase

Donggyun You et al.

Summary: The morphology and size of the a-phase in Fe40Mn40Co10Cr10 non-equiatomic high entropy alloy play a significant role in its mechanical properties. Fine sigma-precipitates can increase strength without severe ductility loss, while coarsened sigma-phase leads to early failure. Controlling the size and dispersion of the sigma-phase to increase sigma/FCC interfaces is essential for developing HEAs with an excellent strength-ductility combination and damage tolerance.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Chemistry, Physical

Influence of Mo/Cr ratio on the lamellar microstructure and mechanical properties of as-cast Al0.75CoCrFeNi compositionally complex alloys

Alex Asabre et al.

Summary: The microstructure and mechanical properties of Al-Co-Cr-Fe-Ni-Mo alloys were studied, and it was found that the variation of Mo content significantly influenced the organization and performance of the alloys. With increasing Mo content, the BCC phase gradually transformed into TCP phases, leading to an increase in microhardness and tensile strength. However, high Mo content made the alloys brittle and resulted in reduced strength at higher temperatures.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Vacuum arc melted and heat treated AlCoCrFeNiTiX based high-entropy alloys: Thermodynamic and microstructural investigations

Saadet Guler et al.

Summary: This study proposes a phase diagram suitable for the AlCoCrFeNiTiX system using ThermoCalc software and compares it with experimental results. The effects of titanium on the microstructure evaluations and phase transformations in high-entropy alloys were investigated.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

The synergistic addition of Al, Ti, Mo and W to strengthen the equimolar CoCrFeNi high-entropy alloy via thermal-mechanical processing

Jiale Man et al.

Summary: In this study, the tensile mechanical properties and microstructures of (CoCrFeNi)((100-x))(WMo)(x) and (CoCrFeNi)((100-x-6))(WMo)(x)(Al Ti)(6) (x = 1, 3, and 5) HEAs were investigated. The results showed that thermal-mechanical processing enhanced the alloys with the precipitation of submicron TCP sigma phase and the addition of Al and Ti further strengthened the alloys through the formation of a heterogeneous microstructure. The synergistic addition of W, Mo, Al and Ti improved the mechanical property of the equimolar CoCrFeNi-HEA, with Ti playing a role in enhancing the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation on microstructure heterogeneity of the HPDC AlSiMgMnCu alloy through 3D electron microscopy

Fei Liu et al.

Summary: The microstructural characteristics of HPDC AlSiMgMnCu alloys were studied using serial block-face scanning electron microscopy. It was found that the volume fractions of a-Fe phase, 13 phase, and Q phase were higher in the skin layer and central zone compared to the segregation band zone. Meanwhile, the volume fractions and sizes of the 0 phase were lower in the skin layer and central zone. The morphology of the phases varied in different regions, with the a-Fe phase showing a plate-like morphology in the skin layer.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Chemistry, Physical

Tuning deformation mechanisms of face-centered-cubic high-entropy alloys via boron doping

Haitao Zhang et al.

Summary: This study demonstrates for the first time the effect of interstitial boron and boron-rich precipitate on the deformation mechanisms of FCC high-entropy alloys. Introducing interstitial boron atoms can transform the dominant deformation mechanism from dislocation slip to deformation twins, while the formation of borides leads to a reversion to dislocation slip.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Precipitation hardening of high entropy alloy CoCrFeMnNi containing titanium

Nadine Eissmann et al.

Summary: The effect of titanium addition beyond the solubility limit was investigated to demonstrate the precipitation hardening possibility of the Cantor alloy CoCrFeMnNi. Following appropriate heat treatment, a significant increase in hardness was detected due to nanometer-sized precipitates identified through TEM analysis.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Superior strength-ductility synergy and strain hardenability of Al/Ta co-doped NiCoCr twinned medium entropy alloy for cryogenic applications

D. D. Zhang et al.

Summary: A novel (NiCoCr)(92)Al6Ta2 medium-entropy alloy was developed with superior cryogenic mechanical properties, showing temperature-dependent mechanical behavior and excellent strength-ductility synergy. The alloy exhibits extraordinary strain hardening capacity and temperature-dependent deformation mechanisms, resulting in enhanced ductility at low temperatures.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Chemistry, Physical

Lattice distortion and atomic ordering of the sigma precipitates in CoCrFeNiMo high-entropy alloy

Sheng-Yun Su et al.

Summary: This study aimed to understand the critical lattice distortion effect of G-phase precipitation in CoCrFeNiMo high-entropy alloys using various quantitative methods. It found values of lattice distortion at different scales and discussed the potential impact of atomic bonding and electronic structure on lattice distortion.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Chemistry, Physical

Microstructure and tensile properties of Co-free Fe4CrNi(AlTi)x high-entropy alloys

Yu Ji et al.

Summary: A series of high Fe-content and Co-free Fe4CrNi(AlTi)(x) high-entropy alloys were designed and the effects of Al and Ti content on microstructures and tensile properties were investigated, revealing a correlation between alloy composition and performance. The Fe4CrNi(AlTi)(0.6) alloy showed a good combination of high strength and large ductility, attributed to the optimal distribution of phases and nanoparticle reinforcements.

INTERMETALLICS (2021)

添加到收藏夹

Article Chemistry, Physical

Mechanical properties of FeMnCoCr high entropy alloy alloyed with C/Si at low temperatures

Fei Yang et al.

Summary: Experimental results show that the microstructure of the high entropy alloy is a single-phase face-centered cubic solid solution, with carbon and silicon completely dissolved in the matrix. With decreasing temperature, the strength and plasticity of the alloy increase, and more secondary nanoscale twins are observed at low temperature.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Twinning engineering of high-entropy alloys: An exercise in process optimization and modeling

Jongun Moon et al.

Summary: By utilizing low-temperature pre-straining and subsequent annealing, the mechanical properties of CoCrFeMnNi high-entropy alloy were improved, confirming the effectiveness of twinning engineering concept.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Tunable mechanical property and strain hardening behavior of a single-phase CoFeNi2V0.5Mo0.2 high entropy alloy

Li Jiang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Deactivating deformation twinning in medium-entropy CrCoNi with small additions of aluminum and titanium

C. E. Slone et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

On the formation of hierarchical microstructure in a Mo-doped NiCoCr medium-entropy alloy with enhanced strength-ductility synergy

Junyang He et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Chemistry, Physical

Microstructural evolution, mechanical and corrosion behaviors of as-annealed CoCrFeNiMox (x=0, 0.2, 0.5, 0.8, 1) high entropy alloys

Zuozhe Niu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

A ductile high entropy alloy strengthened by nano sigma phase

Lu Zhang et al.

INTERMETALLICS (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of Hf on the microstructure and mechanical properties of CoCrFeNi high entropy alloy

Huan Ma et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Structural investigation of the stability in temperature of some high entropy/multi major components alloys as a function of their electronic structure

M. Calvo-Dahlborg et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

G. W. Hu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Chemistry, Physical

Influence of lattice distortion on stacking fault energies of CoCrFeNi and Al-CoCrFeNi high entropy alloys

Shi Qiu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Analysis of damage-tolerance of TRIP-assisted V10Cr10Fe45Co30Ni5 high-entropy alloy at room and cryogenic temperatures

Yong Hee Jo et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Precipitation-driven metastability engineering of carbon-doped CoCrFeNiMo medium-entropy alloys at cryogenic temperature

Hyeonseok Kwon et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of CoCrFeNiWx high entropy alloys reinforced by μ phase particles

Lei Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tuning δ → γ transformation types to relieve mechanical property degradation in a Co-free face-centered cubic metastable high-entropy alloy

Huabei Peng et al.

MATERIALIA (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

An as-cast high-entropy alloy with remarkable mechanical properties strengthened by nanometer precipitates

Gang Qin et al.

NANOSCALE (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Quantitative determination of the lattice constant in high entropy alloys

Zhijun Wang et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Boundary micro-cracking in metastable Fe45Mn35Co10Cr10 high-entropy alloys

Shaolou Wei et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Chemistry, Physical

Effect of μ-precipitates on the microstructure and mechanical properties of non-equiatomic CoCrFeNiMo medium-entropy alloys

Jae Wung Bae et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strengthening FCC-CoCrFeMnNi high entropy alloys by Mo addition

Gang Qin et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Novel Co-rich high performance twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) high-entropy alloys

Daixiu Wei et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hierarchical microstructure design to tune the mechanical behavior of an interstitial TRIP-TWIP high-entropy alloy

Jing Su et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Cr-rich Co-Cr-Fe-Ni high entropy alloys designed by valence electron concentration

Wei Fang et al.

MATERIALS CHEMISTRY AND PHYSICS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Novel Co-rich high entropy alloys with superior tensile properties

Daixiu Wei et al.

MATERIALS RESEARCH LETTERS (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Effect of carbon addition on the microstructure and mechanical properties of CoCrFeNi high entropy alloy

Huang TianDang et al.

SCIENCE CHINA-TECHNOLOGICAL SCIENCES (2018)

添加到收藏夹

Article Chemistry, Physical

Microstructure and properties of novel CoCrFeNiTax eutectic high-entropy alloys

Wenyi Huo et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

The microstructure and high-temperature properties of novel nano precipitation-hardened face centered cubic high-entropy superalloys

Lu Zhang et al.

SCRIPTA MATERIALIA (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Generalized stacking fault energies, ductilities, and twinnabilities of CoCrFeNi-based face-centered cubic high entropy alloys

M. Beyramali Kivy et al.

SCRIPTA MATERIALIA (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Precipitation strengthening of ductile Cr15Fe20Co35Ni20Mo10 alloys

Kaisheng Ming et al.

SCRIPTA MATERIALIA (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

The origin of negative stacking fault energies and nano-twin formation in face-centered cubic high entropy alloys

Y. H. Zhang et al.

SCRIPTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of CoCrFeNiZrx eutectic high-entropy alloys

Wenyi Huo et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Review Materials Science, Multidisciplinary

A critical review of high entropy alloys and related concepts

D. B. Miracle et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

A precipitation-hardened high-entropy alloy with outstanding tensile properties

J. Y. He et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ductile CoCrFeNiMox high entropy alloys strengthened by hard intermetallic phases

W. H. Liu et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Chemistry, Physical

First principles exploration of near-equiatomic NiFeCrCo high entropy alloys

C. Niu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Strengthening of nanoprecipitations in an annealed Al0.5CoCrFeNi high entropy alloy

Sizhe Niu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Physics, Multidisciplinary

A Criterion for Topological Close-Packed Phase Formation in High Entropy Alloys

Yiping Lu et al.

ENTROPY (2015)

添加到收藏夹

Article Chemistry, Physical

Effects of Nb additions on the microstructure and mechanical property of CoCrFeNi high-entropy alloys

W. H. Liu et al.

INTERMETALLICS (2015)

添加到收藏夹

Article Physics, Applied

Predicting the solid solubility limit in high-entropy alloys using the molecular orbital approach

Saad Sheikh et al.

JOURNAL OF APPLIED PHYSICS (2015)

添加到收藏夹

Article Nanoscience & Nanotechnology

Tensile properties of low-stacking fault energy high-entropy alloys

A. J. Zaddach et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Multidisciplinary Sciences

Accelerated exploration of multi-principal element alloys with solid solution phases

O. N. Senkov et al.

NATURE COMMUNICATIONS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Temperature dependence of the mechanical properties of equiatomic solid solution alloys with face-centered cubic crystal structures

Z. Wu et al.

ACTA MATERIALIA (2014)

添加到收藏夹

Article Chemistry, Physical

Effect of Mn and V on structure and mechanical properties of high-entropy alloys based on CoCrFeNi system

G. A. Salishchev et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

添加到收藏夹

Article Multidisciplinary Sciences

A fracture-resistant high-entropy alloy for cryogenic applications

Bernd Gludovatz et al.

SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Guidelines in predicting phase formation of high-entropy alloys

Y. Zhang et al.

MRS COMMUNICATIONS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

F. Otto et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys

F. Otto et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical Properties and Stacking Fault Energies of NiFeCrCoMn High-Entropy Alloy

A. J. Zaddach et al.

JOM (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Age-hardening of the CoCrFeNiMo0.85 high-entropy alloy

Tao-Tsung Shun et al.

MATERIALS CHARACTERIZATION (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Non-crystallographic shear banding in crystal plasticity FEM simulations: Example of texture evolution in α-brass

N. Jia et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of multiprincipal component CoCrFeNiMox alloys

Tao-Tsung Shun et al.

MATERIALS CHARACTERIZATION (2012)

添加到收藏夹

Article Chemistry, Physical

Microstructure and tensile behaviors of FCC Al0.3CoCrFeNi high entropy alloy

Tao-Tsung Shun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2009)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of Si content on the stacking fault energy in γ-Fe-Mn-Si-C alloys: Part I. X-ray diffraction line profile analysis

Xing Tian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

添加到收藏夹

Article Nanoscience & Nanotechnology

A microstructural investigation of adiabatic shear bands in an interstitial free steel

J. F. C. Lins et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructural development in equiatomic multicomponent alloys

B Cantor et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes

JW Yeh et al.

ADVANCED ENGINEERING MATERIALS (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.