相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Numerical study of the effect of surface topography on atomization performance in geometrically sensitive areas of centrifugal nozzles
Lixin Shen et al.
PHYSICS OF FLUIDS (2022)
Picosecond pulsed digital off-axis holography for near-nozzle droplet size and 3D distribution measurement of a swirl kerosene spray
Yingchun Wu et al.
FUEL (2021)
Influence of nozzle geometry on primary and large-scale instabilities in coaxial injectors
Abhijeet Kumar et al.
CHEMICAL ENGINEERING SCIENCE (2020)
Application of big data analysis technique on high-velocity airblast atomization: Searching for optimum probability density function
Andras Urban et al.
FUEL (2020)
Empirical correlation for spray half cone angle in plain-jet airblast atomizers
Andras Urban et al.
FUEL (2020)
On the correlation of the primary breakup length with fuel temperature in pressure swirl nozzle
Shahnaz Rezaei et al.
FUEL (2019)
Towards Adaptive Grids for Atmospheric Boundary-Layer Simulations
J. Antoon van Hooft et al.
BOUNDARY-LAYER METEOROLOGY (2018)
Numerical and experimental study on the spray characteristics of full-cone pressure swirl atomizers
Yubiao Sun et al.
ENERGY (2018)
Ambient density effects on initial flow breakup and droplet size distribution of hollow-cone sprays from outwardly-opening GDI injector
Jeeyeon Jeon et al.
FUEL (2018)
Influence of density ratio on the secondary atomization of liquid droplets under highly unstable conditions
Wei Yang et al.
FUEL (2016)
Liquid flow in a simplex swirl nozzle
Ghobad Amini
INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2016)
Dynamic Characteristics of Open-Type Swirl Injector with Varying Geometry
Yunjae Chung et al.
JOURNAL OF PROPULSION AND POWER (2016)
Effect of geometric parameters on the spray cone angle in the pressure swirl injector
Juan Liu et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART G-JOURNAL OF AEROSPACE ENGINEERING (2013)
An Experimental Investigation on the Effect of Various Swirl Atomizer Orifice Geometries on the Air Core Diameter
Mohd Syazwan Firdaus Mat Rashid et al.
AEROTECH IV: RECENT ADVANCES IN AEROSPACE TECHNOLOGIES (2012)
Measurement of annular liquid film thickness in an open-end swirl injector
Qing-fei Fu et al.
AEROSPACE SCIENCE AND TECHNOLOGY (2011)
Regulated emissions from a direct-injection spark-ignition methanol engine
Chang-Ming Gong et al.
ENERGY (2011)
The granular column collapse as a continuum: validity of a two-dimensional Navier-Stokes model with a μ(I)-rheology
P-Y Lagree et al.
JOURNAL OF FLUID MECHANICS (2011)
Linear Stability Analysis of a Conical Liquid Sheet
Qing-fei Fu et al.
JOURNAL OF PROPULSION AND POWER (2010)
Secondary atomization
D. R. Guildenbecher et al.
EXPERIMENTS IN FLUIDS (2009)
An accurate adaptive solver for surface-tension-driven interfacial flows
Stephane Popinet
JOURNAL OF COMPUTATIONAL PHYSICS (2009)
Effect of geometric parameters on simplex atomizer performance
J Xue et al.
AIAA JOURNAL (2004)
An eddy-viscosity subgrid-scale model for turbulent shear flow: Algebraic theory and applications
AW Vreman
PHYSICS OF FLUIDS (2004)
Gerris: a tree-based adaptive solver for the incompressible Euler equations in complex geometries
S Popinet
JOURNAL OF COMPUTATIONAL PHYSICS (2003)
Prediction of the droplet size and velocity joint distribution for sprays
D Ayres et al.
FUEL (2001)
Numerical prediction of air core diameter, coefficient of discharge and spray cone angle of a swirl spray pressure nozzle
A Datta et al.
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW (2000)