☆ 4.7 Article

Influence mechanism of abrasive belt wear on fatigue resistance of TC17 grinding surface

ENGINEERING FAILURE ANALYSIS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Manufacturing

Machining-induced surface integrity in titanium alloy Ti-6Al-4V: An investigation of cutting edge radius and cooling/lubricating strategies

Guang Chen et al.

Summary: The study focuses on the influence of cutting edge radii and cooling/lubricating conditions on surface integrity of machined components. Experimental analysis shows that larger cutting edge radii lead to material compression into the machined surface, while changes in cooling/lubricating conditions also affect surface integrity. These findings can be applied to improve the service life and functional performance of machined parts.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Review Nanoscience & Nanotechnology

High-strength titanium alloys for aerospace engineering applications: A review on melting-forging process

Qinyang Zhao et al.

Summary: High-strength titanium alloys (HS-TAs) are crucial structural materials for advanced engineering applications. Achieving the synergy of high strength, high ductility, and high toughness has been identified as a technical bottleneck. Two primary strategies, developing novel alloys and innovating processing technologies, have been initiated to overcome this challenge. This review provides an overview of the research status, processing and heat treatment technologies, phase transformation, processing-microstructure-property correlation, and strengthening-toughening mechanism of HS-TAs for aerospace engineering applications.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Engineering, Mechanical

Investigation of surface quality, microstructure, deformation mechanism, and fatigue performance of additively manufactured 304L stainless steel using grinding

Hongzhuang Zhang et al.

Summary: This study comprehensively investigates the surface integrity, residual stress, microstructure, and mechanical properties of 304L stainless steel made by laser powder bed fusion process. The results show that grinding significantly improves the surface quality characteristics and increases the fatigue life. Additionally, ground subsurface cracks and newly formed grains were observed, and their formation mechanisms were discussed.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Article Engineering, Manufacturing

Grinding sustainability analysis using a fatigue failure-related product life indicator

Fernando Moreira Bordin et al.

Summary: This paper introduces a new sustainability indicator based on the rolling contact fatigue life of components determined by the grinding process. A method for calculating this indicator is presented, and a case study is illustrated. The subsurface damage thickness is loosely correlated with fatigue life and introduced as a new indicator. The selected indicators are used as decision-making parameters to showcase the potential of the product life factor as an aggregate sustainability indicator.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-temperature failure mechanism and defect sensitivity of TC17 titanium alloy in high cycle fatigue

Gen Li et al.

Summary: This study investigates the failure mechanism of TC17 titanium alloy under high-temperature high cycle fatigue (HCF) by conducting fatigue tests and multi-scale microstructure characterizations. It is found that an oxygen-rich layer (ORL) on the specimen surface plays a critical role in surface crack initiation, while internal crack initiation with nanograins at high temperatures is a novel finding for titanium alloys. The competition between surface and internal crack initiations at high temperatures is related to the ORL on the surface and dislocation resistance in the inner microstructure.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Aerospace

Effect of creep feed grinding on surface integrity and fatigue life of Ni3Al based superalloy IC10

Shuaiqi Zhang et al.

Summary: Ni3Al-based superalloy IC10 is investigated for its creep feed grinding properties, analyzing the effects of grinding parameters on forces, temperature, and fatigue life. The study concludes that grinding depth is the most influential factor, while surface roughness and hardening also play key roles in fatigue life. Recommended grinding parameters for better surface quality and fatigue life improvement are provided in the study.

CHINESE JOURNAL OF AERONAUTICS (2021)

添加到收藏夹

Article Engineering, Mechanical

Research on the fatigue failure behavior of 1Cr17Ni2 blades ground by abrasive belt with passivation treatment

Yun Huang et al.

Summary: The study investigated the impact of different grinding processes on the fatigue resistance of blades, and found that passivation treatment of abrasive belts and low feed speeds can improve the surface integrity and fatigue life of aero-engine blades. The combination process of abrasive belt passivation treatment and slow feed speed was proposed for anti-fatigue grinding of aero-engine blades.

ENGINEERING FAILURE ANALYSIS (2021)

添加到收藏夹

Article Engineering, Mechanical

Effect of shot peening and vibration finishing on the fatigue behavior of TC17 titanium alloy at room and high temperature

Hailan Shi et al.

Summary: Research shows that the TC17 alloy treated with SP + VF process significantly improves its fatigue performance at room temperature, especially in high-temperature environments. This is mainly due to the fact that the SP + VF process can reduce surface roughness, enhance stability of microstructure, and maintain the residual compressive stress layer relatively stable compared to SP treatment alone.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

添加到收藏夹

Article Engineering, Industrial

Influence of surface integrity induced by multiple machining processes upon the fatigue performance of a nickel based superalloy

Zhirong Liao et al.

Summary: Machining operations significantly alter the surface integrity of nickel based superalloys, influencing their fatigue performance and failure mechanisms. Residual stress induced by machining controls high cycle fatigue, while surface defects from different processes influence fatigue crack initiation and propagation in both low and high cycle regimes.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Industrial

Alumina abrasive wheel wear in ultrasonic vibration-assisted creep-feed grinding of Inconel 718 nickel-based superalloy

Yang Cao et al.

Summary: This study proposed an analytical wear model for wheel wear in UVAPG, successfully predicting the wear volume and revealing a significant increase in wear volume in UVAPG compared to conventional grinding during the steady wear stage. The tangential ultrasonic vibration increases the average unchanged chip thickness and the number of active grinding edges.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Tensile and very high cycle fatigue behaviors of a compressor blade titanium alloy at room and high temperatures

Fulin Liu et al.

Summary: The tensile and fatigue behaviors of TC17 titanium alloy at room temperature and high temperature were studied, where it was found that the tensile strength decreases at high temperature while the elongation remains unchanged. The fatigue S-N curves and failure mode also change with temperature, with the crack initiation mainly attributed to the brittle oxygen-enriched subsurface (BOES) layer at high temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Engineering, Manufacturing

Surface integrity in metal machining-Part II: Functional performance

Andrea La Monaca et al.

Summary: Material removal operations are crucial for manufacturing key components in engineering systems. Understanding the influence of machining-induced features on advanced materials' performance is essential at finer temporal and spatial scales. The interplay between metallurgical and micro-mechanical conditions induced by material removal processes and their in-service response will be thoroughly explored in this review.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

添加到收藏夹

Article Materials Science, Ceramics

Models of grinding-induced surface and subsurface damages in fused silica considering strain rate and micro shape/geometry of abrasive

Huapan Xiao et al.

Summary: Based on the indentation fracture mechanics of brittle materials, correlations between subsurface crack depth and scratch depth induced by different indenters are established, and theoretical models for surface damage and subsurface damage depths are developed. Experimental results show that the hybrid grit models can efficiently predict the depths of damage, reducing errors compared to other shaped grit models.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Mechanical

Comparative study of very high cycle tensile and torsional fatigue in TC17 titanium alloy

Hanqing Liu et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

添加到收藏夹

Article Automation & Control Systems

Tool wear monitoring system in belt grinding based on image-processing techniques

HtunHtun Oo et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of grinding parameters on surface quality, microstructure and rolling contact fatigue behaviors of gear steel for vacuum pump

Bo Kang et al.

VACUUM (2020)

添加到收藏夹

Article Engineering, Mechanical

Wear mechanism in high-speed superabrasive grinding of titanium alloy and its effect on surface integrity

Anirban Naskar et al.

WEAR (2020)

添加到收藏夹

Article Engineering, Manufacturing

Multi-information fusion-based belt condition monitoring in grinding process using the improved-Mahalanobis distance and convolutional neural networks

Junde Qi et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Article Engineering, Mechanical

Influence of tool material and geometry on micro-textured surface in radial ultrasonic vibration-assisted turning

Xianfu Liu et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

添加到收藏夹

Article Engineering, Mechanical

Wear of a Flexible Abrasive Tool

N. V. Syreyshchikova et al.

JOURNAL OF FRICTION AND WEAR (2019)

添加到收藏夹

Article Engineering, Industrial

Effects of cutting conditions on the microstructure and residual stress of white and dark layers in cutting hardened steel

Zhang Fangyuan et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

添加到收藏夹

Article Chemistry, Multidisciplinary

Predictive Modelling and Analysis of Process Parameters on Material Removal Characteristics in Abrasive Belt Grinding Process

Vigneashwara Pandiyan et al.

APPLIED SCIENCES-BASEL (2017)

添加到收藏夹

Article Engineering, Mechanical

Influence of abrasive grain geometry on friction coefficient and wear rate in belt finishing

A. Jourani et al.

TRIBOLOGY INTERNATIONAL (2013)

添加到收藏夹

Article Engineering, Industrial

Comparison of spherical and truncated cone geometries for single abrasive-grain cutting

D. Anderson et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)

添加到收藏夹

Article Engineering, Mechanical

The effect of abrasive grain's wear and contact conditions on surface texture in belt finishing

A. Khellouki et al.

WEAR (2007)

添加到收藏夹

Article Engineering, Manufacturing

A local process model for simulation of robotic belt grinding

X. Ren et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.