4.7 Article

Performance prediction of a cryogenic organic Rankine cycle based on back propagation neural network optimized by genetic algorithm

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Thermodynamics

Prediction and optimization of power output of single screw expander in organic Rankine cycle (ORC) for diesel engine waste heat recovery

Xu Ping et al.

Summary: This paper develops a machine learning prediction model for the power output of a single screw expander driven by experimental data. By optimizing the model using genetic algorithm, it shows improved generalization ability compared to the model without optimization. The model accurately predicts and optimizes the maximum power output and operating parameters of the single screw expander under full operating conditions.

APPLIED THERMAL ENGINEERING (2021)

Article Thermodynamics

Energy, exergy, and economic (3E) analysis of an organic Rankine cycle using zeotropic mixtures based on marine engine waste heat and LNG cold energy

Zhen Tian et al.

Summary: This paper conducts a simulation to compare the thermo-economic performances of zeotropic mixtures and pure fluids in a parallel two-stage organic Rankine cycle (PTORC) driven by waste heat from LNG-fueled ships. The results indicate that zeotropic mixtures do not always have an advantage over pure fluids, with the optimal working fluid combination being R170/R1270-R600. The study also shows that the highest net power output is achieved with R1150-R600a, and LNG regasification should occur in the first-stage condenser for optimal performance.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Thermodynamics

Experimental investigation of 3-kW organic Rankine cycle (ORC) system subject to heat source conditions: A new appraisal for assessment

Yung-Ming Li et al.

Summary: This study experimentally examined the performance of a 3 kW organic Rankine cycle system, finding that the heat source temperature has a greater impact on system efficiency than the heat source flowrate; a new evaluation index, total heat recovery efficiency, was proposed to better reflect system performance.

ENERGY (2021)

Article Thermodynamics

Towards a comprehensive optimization of engine efficiency and emissions by coupling artificial neural network (ANN) with genetic algorithm (GA)

Yaopeng Li et al.

Summary: The study proposes a new approach for optimizing internal combustion engine strategies using the ANN-GA method, which shows higher efficiency, lower computational time, and stronger adaptability compared to traditional methods.

ENERGY (2021)

Article Thermodynamics

A cascade hybrid PSO feed-forward neural network model of a biomass gasification plant for covering the energy demand in an AC microgrid

Cristian Chinas-Palacios et al.

Summary: This study proposes a model based on Artificial Neural Networks and Particle Swarm Optimization algorithm to estimate the biomass needed for a Biomass Gasification Plant to produce syngas to meet energy demand. The results show that the proposed model outperforms existing models in terms of MSE.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Thermodynamics

Thermo-economic optimization of the hybrid geothermal-solar power system: A data-driven method based on lifetime off-design operation

Shuozhuo Hu et al.

Summary: The study proposes a novel data-driven method to predict the off-design performance of a hybrid geothermal-solar power system, enabling proactive design and optimizing system layout. Results show the effectiveness of this approach in improving electricity generation and net present value, with potential thermo-economic advantages. This method can be applied to other power systems for optimization design of renewable energy systems.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Thermodynamics

Introducing machine learning and hybrid algorithm for prediction and optimization of multistage centrifugal pump in an ORC system

Xu Ping et al.

Summary: This study proposed an experimental data-driven isentropic efficiency prediction model based on machine learning, and used algorithms and technologies to enhance predictive ability. By analyzing the influence of operating parameters on isentropic efficiency and determining boundary values using intelligent algorithms, the prediction and optimization of isentropic efficiency of multistage centrifugal pumps was successfully achieved.

ENERGY (2021)

Article Thermodynamics

Investigation on improvement potential of ORC system off-design performance by expander speed regulation based on theoretical and experimental exergy-energy analyses

Shengming Dong et al.

Summary: This study investigated the potential of expander speed regulation for optimizing the performance of an ORC system under off-design working conditions. It identified two different optimal speeds for maximum power output and efficiency. Energy and exergy analyses showed the close relationship between expander speed and actual exergy destruction, highlighting the importance of expander and pump optimization for ORC system performance.

ENERGY (2021)

Article Thermodynamics

Off-design model of an ORC system for waste heat recovery of an internal combustion engine

Rieder de Oliveira Neto et al.

Summary: The study focused on an ORC system to recover energy from the exhaust gases of a stationary diesel engine, with analysis on system parameters, off-design conditions, and economic feasibility. Results showed increased thermal efficiency, reduced fuel consumption, and pollutant gas emissions in the power plant with the implementation of the system.

APPLIED THERMAL ENGINEERING (2021)

Article Thermodynamics

Machine learning prediction of ORC performance based on properties of working fluid

Yannan Peng et al.

Summary: This study focuses on developing machine learning methods to predict the performance of basic ORC and regenerative ORC based on thermodynamic properties of working fluids. ANN models are used to separately predict thermodynamic processes and cycle performances, with a focus on vapor slope modeling and temperature difference for regenerative ORC. The accuracy of cycle performance predictions for both types of ORC is validated using average absolute deviations.

APPLIED THERMAL ENGINEERING (2021)

Article Thermodynamics

Optimal design and operation of an Organic Rankine Cycle (ORC) system driven by solar energy with sensible thermal energy storage

Haoshui Yu et al.

Summary: In this study, the optimal design and operation of an Organic Rankine Cycle (ORC) system driven by solar energy were investigated. A simulation-based optimization model was developed to maximize system efficiency, with findings showing that supercritical ORC outperforms subcritical ORC. Toluene was identified as the best working fluid, while the system efficiency was significantly improved compared to previous studies.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Thermodynamics

Identifying the key system parameters of the organic Rankine cycle using the principal component analysis based on an experimental database

Dong Yan et al.

Summary: The study investigates the impact of system parameters on output in organic Rankine cycle, and determines a key parameter subset through experiments and statistical analysis. Prediction models are developed using machine learning algorithms, with the key parameter subset identified as (pe, eta P, pc, eta SSE).

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Automation & Control Systems

Optimization of lapping process parameters of CP-Ti based on PSO with mutation and BPNN

Kaiqiang Ye et al.

Summary: The study aimed to improve the surface quality of CP-Ti by using free alumina lapping fluid and neural networks, finding optimal process parameters through particle swarm optimization with mutation. Experimental verification showed that the well-trained neural network provided accurate predictions for roughness when experimental data were lacking. Applying the PSO algorithm with mutation to a neural network successfully obtained the optimal process parameter configurations and improved surface quality effectively.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Article Green & Sustainable Science & Technology

Thermodynamic performance evaluation of a geothermal ORC power plant

A. F. Altun et al.

RENEWABLE ENERGY (2020)

Article Thermodynamics

Thermodynamic modeling and analysis of a novel PEMFC-ORC combined power system

Guokun Liu et al.

ENERGY CONVERSION AND MANAGEMENT (2020)

Article Green & Sustainable Science & Technology

Development of a non-linear state estimator for advanced control of an ORC test rig for geothermal application

R. Pili et al.

RENEWABLE ENERGY (2020)

Article Thermodynamics

Experimental analysis of a micro-ORC driven by piston expander for low-grade heat recovery

M. Bianchi et al.

APPLIED THERMAL ENGINEERING (2019)

Article Thermodynamics

Comprehensive assessment of the impact of operating parameters on sub 1 kW compact ORC performance

Yongtae Jang et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Thermodynamics

Experimental investigation of lubricant oil on a 3 kW organic Rankine cycle (ORC) using R123

Yong-qiang Feng et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Thermodynamics

Dynamic test and verification of model-guided ORC system

Ying Zhang et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Thermodynamics

Dynamic simulation and experiments of a low-cost small ORC unit for market applications

Gianluca Carraro et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Thermodynamics

The energy flow method for modeling and optimization of Organic Rankine Cycle (ORC) systems

Guangfeng Shen et al.

ENERGY CONVERSION AND MANAGEMENT (2019)