☆ 4.7 Article

Eutectic growth kinetics and microscopic mechanical properties of rapidly solidified CoCrFeNiMo0.8 high entropy alloy

ACTA MATERIALIA (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

Evolution of microstructure and mechanical properties during annealing of heavily rolled AlCoCrFeNi2.1 eutectic high-entropy alloy

Adrianna Lozinko et al.

Summary: The microstructure and mechanical properties of a 90% cold-rolled AlCoCrFeNi2.1 eutectic high-entropy alloy undergo changes during annealing at 800 degrees C. Recrystallization occurs faster in the FCC phase compared to the B2 regions, resulting in increased grain size. Partially recrystallized samples produced by annealing exhibit a combination of high yield strength and good ductility.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanism of microstructure evolution and spheroidization in ultrafine lamellar CoCrFeNi(Nb0.5/Ta0.4) eutectic high entropy alloys upon hot deformation

Barnasree Chanda et al.

Summary: This paper reports the microstructure evolution and spheroidization of ultrafine lamellar high entropy alloys (EHEAs) under hot deformation. The experiments on CoCrFeNiNb0.5 and CoCrFeNiTa0.4 alloys at different temperatures reveal their different yield strengths and strain hardening behaviors, as well as deformation softening at high temperatures. In addition, the microstructural coarsening and lamellar instabilities during the evolution process are characterized.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Chemistry, Physical

Rapid solidification of AlCoCrFeNi2.1 High-entropy Alloy

A. Nassar et al.

Summary: The effect of cooling rate on the dual-phase AlCoCrFeNi2.1 Eutectic High-Entropy Alloy was investigated. The microstructure of AlCoCrFeNi2.1 gradually evolved with increasing cooling rate, and different crystal morphologies were observed.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strength and plasticity of lamellar vs. fibrous eutectic Mg-Al nanocomposites: An in-situ microcompression study

Soodabeh Azadehranjbar et al.

Summary: Magnesium alloys are appealing for automotive and aerospace applications due to their low density and high strength-to-weight ratio. However, their current use is limited by low strength and poor formability at ambient temperatures. Two-phase nanostructured materials offer a promising solution to enhance the mechanical properties of magnesium alloys, with either fibrous or lamellar morphologies formed via eutectic transformation. During mechanical testing, the lamellar morphology showed superior strength and plasticity compared to the fibrous morphology and pure magnesium. The higher strength in the fibrous eutectic came at the expense of lower plasticity, while the high plasticity of the lamellar morphology was attributed to factors such as high dislocation activity and role of alpha layers in restricting shear instabilities.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effects of annealing on severely cold-rolled equiatomic HfNbTiZr high entropy alloy

Chun-Hsiang Tu et al.

Summary: The study found that annealing of HfNbTiZr HEA can increase its hardness, and the hardening effect is mainly associated with the formation of HCP precipitates.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Chemistry, Physical

Phase separation and microhardness of rapidly solidified high-entropy CoCrFeNiCux alloys

W. L. Wang et al.

Summary: The addition of Cu element into CoCrFeNi high entropy alloy leads to metastable phase separation and the formation of obvious segregation zones. With the increase of undercooling, the dendritic growth velocity of the alloy increases, but it gradually declines with the enhancement of Cu content.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Crystallography

Mechanical Behavior of Al-Al2Cu-Si and Al-Al2Cu Eutectic Alloys

Qian Lei et al.

Summary: This study utilized laser rapid solidification technique to refine the microstructure of ternary Al-Cu-Si and binary Al-Cu eutectic alloys, leading to significantly enhanced compressive strength and improved plasticity compared to the conventional casting alloys. The improved mechanical properties were attributed to the microstructural refinement and hierarchical eutectic morphology achieved through laser remelting.

CRYSTALS (2021)

添加到收藏夹

Article Chemistry, Physical

Microstructures and mechanical properties of CrFeNi2Nbx eutectic multicomponent alloys

Won-hyuk Lee et al.

Summary: The effects of Nb content on microstructures and mechanical properties in Co-free CrFeNi2Nbx alloys were investigated. Increasing Nb content led to changes in microstructures and improved mechanical properties, with a reduction in ductility. The CrFeNi2Nb0.6 alloy achieved a high maximum fracture strength.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

In situ study of non-equilibrium solidification of CoCrFeNi high-entropy alloy and CrFeNi and CoCrNi ternary suballoys

Angelo F. Andreoli et al.

Summary: The solidification behavior of the CoCrFeNi high-entropy alloy, ternary CrFeNi, and CoCrNi medium-entropy suballoys was studied using high-speed video and synchrotron X-ray diffraction techniques. The results showed that the crystal-growth velocities of these alloys were comparable to Fe-Ni and Fe-Cr-Ni alloys, indicating similar crystallization kinetics. The effect of melt undercooling on the microstructure of solidified samples was also analyzed and discussed.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure stability during high temperature deformation of CoCrFeNiTa eutectic high entropy alloy through nano-scale precipitation

Naishalkumar Shah et al.

Summary: The study focused on the CALPHAD guided design of a hypo-eutectic high entropy alloy with a dual-phase microstructure, which exhibited excellent high-temperature mechanical properties. The addition of alloying elements and thermal effects led to the formation of multiple fine precipitates, extending the usable temperature range of the alloy. Under room temperature conditions, the alloy showed good mechanical performance and at high temperatures, there were various kinds of precipitates in the FCC solution phase.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Hierarchical crack buffering triples ductility in eutectic herringbone high-entropy alloys

Peijian Shi et al.

Summary: The study demonstrates a directionally solidified eutectic high-entropy alloy with a hierarchically organized herringbone structure that reconciles crack tolerance and high elongation. The self-buffering herringbone material achieves an ultrahigh uniform tensile elongation while maintaining strength.

SCIENCE (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Remelting induced fully-equiaxed microstructures with anomalous eutectics in the additive manufactured Ni32Co30Cr10Fe10Al18 eutectic high-entropy alloy

Kexuan Zhou et al.

Summary: This study demonstrates a new approach to promote the formation of fully-equiaxed microstructures in the additive manufacturing of Ni32Co30Cr10Fe10Al18 eutectic high-entropy alloy through remelting-induced columnar-to-equiaxed transformation. The research shows promising isotropic mechanical properties and a superior combination of strength and ductility compared to conventional and other printed high-entropy alloys.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Design of a new cobalt base nano-lamellar eutectic high entropy alloy

R. J. Vikram et al.

Summary: This study focuses on the development of cobalt-base high entropy alloy for high temperature applications based on valence electron concentration (VEC). The newly developed HEA exhibited a two-phase microstructure with remarkable mechanical properties, showing potential for high temperature applications.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Systematic Development of Eutectic High Entropy Alloys by Thermodynamic Modeling and Experimentation: An Example of the CoCrFeNi-Mo System

Muhammad Mukarram et al.

Summary: This study evaluated the possibility of developing a eutectic microstructure by adding Mo to CoCrFeNi alloy, successfully obtaining a eutectic mixture consisting of FCC phase and intermetallic phases, significantly increasing the hardness and yield strength of the samples.

METALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Design and characterization of eutectic refractory high entropy alloys

N. Yurchenko et al.

Summary: Eutectic alloys with near-equilibrium structures, impressive strength-ductility trade-off, and perfect castability were designed using a CALPHAD approach. Alloying with Cr and Al induced the formation of hypoeutectic, eutectic, and hypereutectic structures due to Laves phase precipitation, improving the mechanical characteristics of the alloys. The stable B2/C14 Laves phase microstructure after plastic deformation at high temperatures and the precipitation of a new D0(19) structured phase were observed, indicating new approaches for designing RHEAs with promising mechanical properties.

MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

AlNiCrFeMn Equiatomic High Entropy Alloy: A Further Insight in Its Microstructural Evolution, Mechanical and Surface Degradation Response

E. Ananiadis et al.

METALS AND MATERIALS INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interface-mediated plasticity of nanoscale Al-Al2Cu eutectics

Guisen Liu et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Growth kinetics, microhardness and microstructure evolution of undercooled FeCoNiCuSn high entropy alloy

M. R. Rahul et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hall-Petch and inverse Hall-Petch relations in high-entropy CoNiFeAlxCu1-x alloys

Shuai Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Chemistry, Physical

Microstructural refinement and anomalous eutectic structure induced by containerless solidification for high-entropy Fe-Co-Ni-Si-B alloys

Kang Zhao et al.

INTERMETALLICS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Exotic colony formation in Sn-Te eutectic system

Shanmukha Kiran Aramanda et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution and mechanical properties of a novel CrNbTiZrAlx (0.25 ≤ x ≤ 1.25) eutectic refractory high-entropy alloy

Man Zhu et al.

MATERIALS LETTERS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and Mechanical Properties of BCC-FCC Eutectics in Ternary, Quaternary and Quinary Alloys From the Al-Co-Cr-Fe-Ni System

Daniel Roehrens et al.

FRONTIERS IN MATERIALS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhancing the mechanical properties of casting eutectic high entropy alloys with Mo addition

Zhongsheng Yang et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Engineering heterogeneous microstructure by severe warm-rolling for enhancing strength-ductility synergy in eutectic high entropy alloys

S. R. Reddy et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Chemistry, Physical

A new CrFeNi2Al eutectic high entropy alloy system with excellent mechanical properties

Xi Jin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the origin of anomalous eutectic growth from undercooled melts: Why re-melting is not a plausible explanation

Andrew M. Mullis et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Crystal orientation relationships in ternary eutectic Al-Al2Cu-Ag2Al

Philipp Steinmetz et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

A superfine eutectic microstructure and the mechanical properties of CoCrFeNiMox high-entropy alloys

Yong Guo et al.

JOURNAL OF MATERIALS RESEARCH (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

A novel Fe20Co20Ni41Al19 eutectic high entropy alloy with excellent tensile properties

Xi Jin et al.

MATERIALS LETTERS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Eutectic growth in two-phase multicomponent alloys

Oriane Senninger et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of refractory high entropy (Mo0.5NbHf0.5ZrTi)BCC/M5Si3 in-situ compound

N. N. Guo et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of the new Nb25Sc25Ti25Zr25 eutectic high entropy alloy

L. Rogal et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Tailoring nanostructures and mechanical properties of AlCoCrFeNi2.1 eutectic high entropy alloy using thermo-mechanical processing

I. S. Wani et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Nb addition on structural evolution and properties of the CoFeNi2V0.5 high-entropy alloy

Li Jiang et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2015)

添加到收藏夹

Article Physics, Multidisciplinary

Scaling Theory of Two-Phase Dendritic Growth in Undercooled Ternary Melts

Silvere Akamatsu et al.

PHYSICAL REVIEW LETTERS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

The origin of anomalous eutectic structures in undercooled Ag-Cu alloy

C. R. Clopet et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of multiprincipal component CoCrFeNiMox alloys

Tao-Tsung Shun et al.

MATERIALS CHARACTERIZATION (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Spherical ternary eutectic cells formed during free fall

F. P. Dai et al.

PHILOSOPHICAL MAGAZINE LETTERS (2009)

添加到收藏夹

Article Nanoscience & Nanotechnology

Containerless rapid solidification of highly undercooled Co-Si eutectic alloys

WJ Yao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

添加到收藏夹

Article Chemistry, Physical

Microstructural evolution during containerless rapid solidification of Ni-Mo eutectic alloys

WJ Yao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2003)

添加到收藏夹

Article Physics, Fluids & Plasmas

Eutectic growth under acoustic levitation conditions -: art. no. 061601

WJ Xie et al.

PHYSICAL REVIEW E (2002)

添加到收藏夹

Article Thermodynamics

The determination of dynamic and equlibrium solid/liquid transformation data for Sn-Pb using DSC

AS Pedersen et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.