☆ 4.6 Article

Application of Particle Swarm Optimization for Improvement of Peel Strength in a Laminated Double-Lap Composite Joint

APPLIED SCIENCES-BASEL (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Chemical

Optimization of adhesive single-lap joints under bending moment

Mojtaba Hassan Vand et al.

Summary: This paper investigates the optimization of stacking sequence of composite laminate adherends in an adhesive single lap joint under bending moment to minimize peel and shear stress of the adhesive layer. Various assumptions and their effects on stress equations are presented. The analytical method and finite element method show good agreement, with the optimization process using single-objective and multi-objective bees algorithms to find the best and worst stacking sequences. Results indicate that the maximum stress is highly dependent on stiffness in the adherends, with the optimal model having nearly equal stiffness while the worst models show significant differences causing destructive stress in thinner adherends.

JOURNAL OF ADHESION (2022)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Disaster relief supply chain design for personal protection equipment during the COVID-19 pandemic

Behzad Mosallanezhad et al.

Summary: This paper develops a multi-objective, multi-product, and multi-period model aiming to optimize total cost and shortage for personal protection equipment demands satisfaction in response to the COVID-19 outbreak. Through validation and testing, the study demonstrates the feasibility and value of the model and algorithms for practical application, and statistical analysis concludes on their utility and effectiveness.

APPLIED SOFT COMPUTING (2021)

添加到收藏夹

Article Materials Science, Composites

Optimization design and 3D printing of curvilinear fiber reinforced variable stiffness composites

Zhanghao Hou et al.

Summary: The paper proposed an optimized design method based on stress gradient distribution for CFRCSs to improve strength efficiency of continuous fiber reinforced composites. By studying the mechanism of fiber content regulation and proposing an adaptive feed calculation method, 3D printing of CFRCSs was achieved, leading to a reduction in stress concentration factor and an increase in ultimate tensile strength. The optimized design approach aligns fiber distribution with stress distribution, while redistributing stress to reduce concentration, ultimately enhancing ultimate strength.

COMPOSITES SCIENCE AND TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Topology optimization with discrete geometric components made of composite materials

Hollis Smith et al.

Summary: A novel topology optimization method has been proposed for designing structures made of orthotropic, fiber-reinforced bars to maximize stiffness. The method extends geometry projection to use cylindrical bars reinforced with continuous fibers and ensures optimal material selection at intersection of bars. Numerical examples demonstrate the efficacy of the method in stiffness-based design of frame structures in 2D and 3D.

COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

A multi-objective optimizer-based model for predicting composite material properties

Hongfang Lu et al.

Summary: A hybrid model combining multi-objective grey wolf optimizer and support vector machine was proposed to predict composite material properties in six datasets. The results showed that the model performed well in property prediction, and the prediction accuracy was closely related to the amount of data in the training set.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Mechanics

Comparison of GA and topology optimization of adherend for adhesively bonded metal composite jointsI

Edore G. Arhore et al.

Summary: The study found that the geometry of the outer adherend directly affects the strength of adhesively bonded joint under tensile load, while it has little impact on joints subjected to bending load. Genetic algorithm and topology optimization methods show differences in optimizing the joint geometry, with the optimum joint produced by the topology optimization offering the highest strength overall.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2021)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Shrimp closed-loop supply chain network design

Behzad Mosallanezhad et al.

Summary: Recent developments in the food industry have attracted attention from both academic and industrial practitioners. This paper focuses on shrimp as a well-known seafood and proposes a mathematical model for the Shrimp Supply Chain (SSC) to minimize total costs. The study utilizes various metaheuristics and conducts real-world applications to validate the effectiveness of the model and solution methods.

SOFT COMPUTING (2021)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Optimization techniques for damage detection of composite structure: A review

Nikhil P. Raut et al.

Summary: Composite materials used in aerospace are prone to damage, especially from low velocity impacts. Structural Health Monitoring (SHM) is essential for detecting and classifying damage caused by low velocity impacts. By using accelerometers and computational techniques, the extent of damage can be assessed with a focus on improving efficiency for damage detection.

MATERIALS TODAY-PROCEEDINGS (2021)

添加到收藏夹

Article Engineering, Chemical

Stress analysis of double-lap bi-material joints bonded with thick adhesive

Mohamed Nasr Saleh et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2020)

添加到收藏夹

Article Thermodynamics

Damage detection of carbon fiber reinforced plastic π adhesive-bonded joints based on the peeling stress reconstruction with hybrid artificial fish swarm and frog leaping algorithm

Xiangyang Huang et al.

ADVANCES IN MECHANICAL ENGINEERING (2019)

添加到收藏夹

Article Chemistry, Physical

Interfacial Stress Analysis of Adhesively Bonded Lap Joint

Shiuh-Chuan Her et al.

MATERIALS (2019)

添加到收藏夹

Article Mechanics

Load distribution in threads of porous metal-ceramic functionally graded composite joints subjected to thermomechanical loading

Wenbin Zhou et al.

COMPOSITE STRUCTURES (2015)

添加到收藏夹

Article Engineering, Multidisciplinary

Preparation and thermodynamic analysis of the porous ZrO2/(ZrO2 + Ni) functionally graded bolted joint

Wenbin Zhou et al.

COMPOSITES PART B-ENGINEERING (2015)

添加到收藏夹

Article Mechanics

Analysis and optimization of hybrid double lap aluminum-GFRP joints

G. Di Franco et al.

COMPOSITE STRUCTURES (2014)

添加到收藏夹

Article Engineering, Chemical

Structural shape optimization of bonded joints using the ESO method and a honeycomb-like mesh

Rene Quispe Rodriguez et al.

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2014)

添加到收藏夹

Article Engineering, Chemical

Geometrical Optimization of the Overlap in Mixed Adhesive Lap Joints

O. Bavi et al.

JOURNAL OF ADHESION (2013)

添加到收藏夹

Proceedings Paper Engineering, Multidisciplinary

An Overview of Particle Swarm Optimization Variants

Muhammad Imran et al.

MALAYSIAN TECHNICAL UNIVERSITIES CONFERENCE ON ENGINEERING & TECHNOLOGY 2012 (MUCET 2012) (2013)

添加到收藏夹

Article Mechanics

An investigation into the stresses in double-lap adhesive joints with laminated composite adherends

M. Y. Tsai et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2010)

添加到收藏夹

Article Engineering, Civil

Optimal design of composite laminates for minimizing delamination stresses by particle swarm optimization combined with FEM

Jianqiao Chen et al.

STRUCTURAL ENGINEERING AND MECHANICS (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.