☆ 4.5 Article

Effect of Combined Forming and Aging Processes on the Mechanical Properties of the Precipitation-Hardenable High-Strength Aluminum Alloys AA6082 and AA7075

METALS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

The effect of pre-ageing/stretching on the ageing-hardening behavior of Al-Zn-Mg-Cu alloys correlated with Zn/Mg ratio

Yan Zou et al.

Summary: Pre-ageing and pre-stretching can significantly affect the precipitation during artificial ageing in Al-Zn-Mg-Cu alloys, leading to improvements in strength and hardness. The effects of pre-ageing are consistent in enhancing strength, while pre-stretching shows varying effects depending on the alloy composition. Both pre-ageing and pre-stretching are effective ways to reduce PFZ width by promoting precipitation near the grain boundary.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparisons of Age Hardening and Precipitation Behavior in 7075 Alloy Under Single and Double-Stage Aging Treatments

Yun Fan et al.

Summary: Various heat treatments were conducted on 7075 alloy in this study to reduce treatment time while achieving similar mechanical properties as the traditional T6 tempered alloy. Hardness tests showed that the double aging treatment and single aging treatment had high similarity in precipitates, mainly consisting of Cr-containing large dispersoids and fine precipitates. Advanced microscopy techniques were used to compare the two treatments.

METALS AND MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of thermo-mechanical processing on quench-induced precipitates morphology and mechanical properties in high strength AA7075 aluminum alloy

E. Scharifi et al.

Summary: The research found that the tool temperature significantly affects the strength and microstructure of AA7075 aluminum alloy, causing fundamental changes in microstructure and strain hardening behavior when exceeding a certain temperature limit. At tool temperatures below 200℃, there is only a slight decrease in tensile strength, while above 200℃, there is a significant drop in tensile strength and an increase in the initial strain hardening rate.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Aging under Stress on Mechanical Properties and Microstructure of EN AW 7075 Alloy

Seyed Vahid Sajadifar et al.

Summary: The study found that stress-aging in EN AW 7075 alloy can increase strength and hardness, accelerate precipitation kinetics, and changes in the morphology and size of precipitates can affect the improvement of mechanical properties.

METALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of pre-stretching on the mechanical behaviour of three artificially aged 6xxx series aluminium alloys

Henrik Granum et al.

Summary: The study found that pre-stretching affects the mechanical properties of different aluminum alloys, with profiles pre-stretched by 4.0% showing slightly lower yield strength but higher failure strain compared to profiles pre-stretched by 0.5%, with fewer visible cracks. The experimental results matched the predictions made by the nanostructure model NaMo.

MATERIALS TODAY COMMUNICATIONS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the influence of in situ sound wave superposition on the microstructure of laser welded 7000 aluminum alloys

S. Voelkers et al.

JOURNAL OF ADVANCED JOINING PROCESSES (2020)

添加到收藏夹

Article Thermodynamics

Effect of Tool Temperature on Mechanical Properties and Microstructure of Thermo-Mechanically Processed AA6082 and AA7075 Aluminum Alloys

S. Sajadifar et al.

HTM-JOURNAL OF HEAT TREATMENT AND MATERIALS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fatigue and corrosion behavior of in-service AA7075 aircraft component after thermo-mechanical and retrogression and re-aging treatments

Selim Gurgen et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS (2019)

添加到收藏夹

Proceedings Paper Engineering, Manufacturing

Thermo-mechanical forming procedure of high strength Aluminum sheet with improved mechanical properties and process efficiency

Emad Scharifi et al.

18TH INTERNATIONAL CONFERENCE ON SHEET METAL, SHEMET 2019 - NEW TRENDS AND DEVELOPMENTS IN SHEET METAL PROCESSING (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Properties of AA7075 aluminum alloy in aging and retrogression and reaging process

Gokhan Ozer et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2017)

添加到收藏夹

Review Engineering, Industrial

A review on tailored blanks-Production, applications and evaluation

Marion Merklein et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Combined effect of deformation and artificial aging on mechanical properties of Al-Mg-Si Alloy

Michal Kolar et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Double aging and thermomechanical heat treatment of AA7075 aluminum alloy extrusions

S. V. Emani et al.

JOURNAL OF MATERIALS SCIENCE (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.