☆ 4.6 Article

Enhancing carrier transport in flexible CZTSSe solar cells via doping Li strategy

JOURNAL OF ENERGY CHEMISTRY (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Highly efficient Cu2ZnSn(S,Se)4 bifacial solar cell via a composition gradient strategy through the molecular ink

Saqib Nawaz Khan et al.

Summary: By developing a composition gradient strategy, this research successfully fabricated a 6.82% efficient CZTSSe solar cell on an FTO substrate. The composition gradient enhances the crystallinity of the absorber, reduces surface roughness, and decreases device parasitic losses, leading to higher fill factor, open-circuit voltage, and conversion efficiency.

SCIENCE CHINA-MATERIALS (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

10.24% Efficiency of Flexible Cu2ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Weihao Xie et al.

Summary: In this study, the authors developed a selenization technique to improve the quality of the CZTSSe layer in flexible solar cells. By pre-evaporation selenization, they were able to promote crystallization and reduce defects in the CZTSSe absorber, resulting in higher conversion efficiency. This safe and efficient method could offer a new strategy for high-efficiency flexible CZTSSe solar cells.

SMALL (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Back Shallow Ge Gradient Enhanced Carrier Separation for CZTSe Solar Cells through a Coselenization Process

Jingling Liu et al.

Summary: Researchers demonstrated a CZTSe solar cell with a shallow Ge gradient, achieving an efficiency of over 10%. By using a GeSe2-Se coselenization process, they improved band tailing, junction quality, and carrier separation in the device, marking a significant breakthrough for Ge-graded CZTSe solar cells and offering a promising approach for developing Ge-involved solar cells.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Achieving Low VOC-deficit Characteristics in Cu2ZnSn(S,Se)4 Solar Cells through Improved Carrier Separation

Vijay Karade et al.

Summary: This study investigates the surface potential and the impact of compositional ratios on the device performance of kesterite-based thin-film solar cells. The findings suggest that at the optimal compositional ratio of Cu/(Zn+Sn) ≈ 0.6, there is a significant improvement in power conversion efficiency.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Engineering, Electrical & Electronic

Effects of irradiation of ZnO/CdS/Cu2ZnSnSe4/Mo/glass solar cells by 10 MeV electrons on photoluminescence spectra

M. A. Sulimov et al.

Summary: Solar cells with the ZnO/CdS/Cu2ZnSnSe4/Mo/glass structure were studied using photoluminescence (PL) before and after irradiation with high energy electrons. The PL spectra showed dominant bands from different layers, and irradiation led to a decrease in intensity without affecting the band tails. The red shift rate of the dominant band increased after irradiation, suggesting the formation of deep non-radiative traps.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells with Shallow LiZn Acceptor Defects Enabled by Solution-Based Li Post-Deposition Treatment

Mingrui He et al.

Summary: The incorporation of lithium in kesterite Cu2ZnSn(S,Se)(4) (CZTSSe) materials has been experimentally proven to improve electronic quality in photovoltaic devices. A solution-based lithium post-deposition treatment was reported to further enhance efficiency by uniformly incorporating lithium into grain interiors, leading to a significant efficiency boost from 9.3% to 10.7%.

ADVANCED ENERGY MATERIALS (2021)

添加到收藏夹

Article Chemistry, Physical

Efficient and Composition-Tolerant Kesterite Cu2ZnSn(S, Se)4 Solar Cells Derived From an In Situ Formed Multifunctional Carbon Framework

Xiao Xu et al.

Summary: Broadening the processing window is crucial for efficient CZTSSe solar cells. This study presents a new approach using TGA-ammonia based water solution method to achieve high efficiency CZTSSe solar cells, revealing the importance of a conductive carbon framework layer and the phase-segregation growth behavior of CZTSSe grains in improving cell performance. This provides new insights into regulating crystal growth of CZTSSe film for enhanced cell efficiency.

ADVANCED ENERGY MATERIALS (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Sodium Effects on the Diffusion, Phase, and Defect Characteristics of Kesterite Solar Cells and Flexible Cu2ZnSn(S,Se)4 with Greater than 11% Efficiency

Kee-Jeong Yang et al.

Summary: This study investigates the effects of Na doping on the efficiency of kesterite solar cells by applying a NaF layer at different positions within precursors. The NaF layer limits Zn diffusion, suppresses Cu-Zn alloy formation, and provides reactive Se and S to the absorber layer, reducing the impact of Na and improving efficiency. By applying NaF between the Zn layer and back contact and between the Cu and Sn layers, efficiency values of 11.16% and 11.19% are achieved for flexible CZTSSe solar cells.

ADVANCED FUNCTIONAL MATERIALS (2021)

添加到收藏夹

Article Chemistry, Applied

Li2S doping into CZTSe drives the large improvement of VOC of solar cell

Zhan Shen et al.

Summary: By evaporating Li2S during selenization process to provide both alkali metal and sulfur to CZTSe film, the quality of the film is improved and the recombination at grain boundaries is decreased. The synergy of sulfur and lithium leads to an increase in the performance of the treated absorber.

JOURNAL OF ENERGY CHEMISTRY (2021)

添加到收藏夹

Article Chemistry, Applied

High-efficiency ultra-thin Cu2ZnSnS4 solar cells by double-pressure sputtering with spark plasma sintered quaternary target

Ping Fan et al.

Summary: In this study, a highly efficient and ultra-thin CZTS solar cell was obtained using double-pressure sputtering technology. The reduction in damage to the Mo contact surface improved the reflectivity of incident light and promoted the collection of photogenerated carriers.

JOURNAL OF ENERGY CHEMISTRY (2021)

添加到收藏夹

Article Chemistry, Physical

Efficiency Improvement of Flexible Cu2ZnSn(S,Se)4 Solar Cells by Window Layer Interface Engineering

Quanzhen Sun et al.

Summary: By utilizing a modified window layer structure (S/CdS/ITO), the performance of flexible CZTSSe solar cells has been enhanced, achieving an efficiency of 9.2%. The introduction of MgF2 antireflection coatings leads to a 6% improvement in the average J(sc) of the devices, with a champion device reaching an efficiency of 9.7%.

ACS APPLIED ENERGY MATERIALS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Insights into High-Efficiency Ag-Alloyed CZTSSe Solar Cells Fabricated through Aqueous Spray Deposition

Temujin Enkhbat et al.

Summary: Kesterite Cu2ZnSnSe4 (CZTSe), Cu2ZnSn(S,Se)(4) (CZTSSe), and Cu2ZnSnS4 (CZTS) solar cells exhibit lower open-circuit voltages than their theoretical values, hindering efficiency improvement and mass production. By substituting Ag into CZTSSe, the Cu/Zn disorder can be reduced, leading to enhanced performance in solar cells.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Energy & Fuels

Two local built-in potentials of H2S processed CZTSSe by complex impedance spectroscopy

Sanghyun Lee et al.

Summary: We fabricated CZTSSe solar cells using H2S sulfo-selenization processes and investigated the electronic structure at the PN hetero- and back contact junctions by impedance spectroscopy. A developed equivalent circuit model was optimized to characterize the built-in potential of two local junction interfaces. Through modeling and numerical simulations, the built-in potential of the heterojunction was determined to be 956 meV, while the back contact junction had a built-in potential of 476 meV.

SOLAR ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

An effective Li-containing interfacial-treating strategy for performance enhancement of air-processed CZTSSe solar cells

Xiao-Fei Dong et al.

Summary: In this study, a simple and effective method of coating a LiOH layer on the CZTS precursor film before selenization is demonstrated to significantly increase the open-circuit voltage and efficiency of CZTSSe solar cells. This LiOH coating approach shows potential for element doping and improving device performance.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Novel symmetrical bifacial flexible CZTSSe thin film solar cells for indoor photovoltaic applications

Hui Deng et al.

Summary: The research focuses on designing symmetrical bifacial CZTSSe solar cells to efficiently harvest indoor energy. Using double-sided deposition techniques, the cells achieve consistent efficiency and cost savings.

NATURE COMMUNICATIONS (2021)

添加到收藏夹

Review Chemistry, Applied

Interface engineering of p-n heterojunction for kesterite photovoltaics: A progress review

Mingrui He et al.

Summary: Kesterite Cu2ZnSn(S,Se)(4) (CZTSSe) is a promising thin-film photovoltaic technology with tunable bandgap, but its efficiency is still below the theoretical limit. The characteristics of buffer layers and interfaces play a key role in efficiency improvement. Future improvements should focus on altering interface characteristics towards achieving the ideal interface.

JOURNAL OF ENERGY CHEMISTRY (2021)

添加到收藏夹

Article Energy & Fuels

Impact of Cation Substitution in (AgxCu1-x)2ZnSnSe4 Absorber-Based Solar Cells toward 10% Efficiency: Experimental and Theoretical Analyses

Shaham Quadir et al.

Summary: In this study, a cation substitution method incorporating Ag ions was introduced to control and passivate defect states in the bandgap of kesterite CZTSe, resulting in reduced density and depth of intrinsic defects. The introduction of 10% Ag-alloyed CZTSe demonstrated the shallowest defect states, less nonradiative recombination, and achieved the best power conversion efficiency of 10.2%.

SOLAR RRL (2021)

添加到收藏夹

Article Energy & Fuels

Interface Recombination of Cu2ZnSnS4 Solar Cells Leveraged by High Carrier Density and Interface Defects

Jianjun Li et al.

Summary: The study identified critical factors governing the interface recombination in CZTS solar cells, including the carrier density of the absorber and acceptor-like interface defects. Eliminating interface defects and adjusting absorber carrier density are essential ways to improve the performance of CZTS solar cells.

SOLAR RRL (2021)

添加到收藏夹

Article Energy & Fuels

A Universal and Facile Method of Tailoring the Thickness of Mo(Sx,Se1-x)2, Contributing to Highly Efficient Flexible Cu2ZnSn(S,Se)4 Solar Cells

Sijie Ge et al.

Summary: This study presents a strategy to suppress the over-thick Mo(S-x,Se1-x)(2) layer on the back contact by adjusting the proportion of sulfur, which leads to a significant improvement in total area efficiency of flexible CZTSSe solar cells. The method is also applicable to other absorber materials and demonstrates universality.

SOLAR RRL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of sodium doping on crystal growth and band matching of the heterojunction in flexible CZTS solar cells

Qichen Zhao et al.

Summary: Treating kesterite layers with sodium has been proven to improve the photovoltaic performance of CZTS solar cells. In this research, flexible CZTS solar cells were doped with sodium from various sources using a simple post-treatment method, resulting in improved crystal quality and photoelectric properties. Further optimization of the doping concentration showed enhanced grain growth and adhesion between film layers, leading to a maximum efficiency of 5.83% for the flexible CZTS solar cell.

JOURNAL OF MATERIALS CHEMISTRY C (2021)

添加到收藏夹

Article Chemistry, Physical

Fabrication of high-efficiency Cu2(Zn,Cd)SnS4 solar cells by a rubidium fluoride assisted co-evaporation/annealing method

Shijin Wang et al.

Summary: The study successfully enhanced the quality of CCZTS thin films and solar devices through Rb incorporation, leading to improvements in bulk and interface properties and carrier collection efficiency enhancement, achieving a champion efficiency of 10.64%.

JOURNAL OF MATERIALS CHEMISTRY A (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Underlying mechanism of the efficiency loss in CZTSSe solar cells: Disorder and deep defects

Biwen Duan et al.

SCIENCE CHINA-MATERIALS (2020)

添加到收藏夹

Review Chemistry, Physical

Defect suppression in multinary chalcogenide photovoltaic materials derived from kesterite: progress and outlook

Qingwen Tian et al.

JOURNAL OF MATERIALS CHEMISTRY A (2020)

添加到收藏夹

Article Chemistry, Physical

An efficient Li+-doping strategy to optimize the band alignment of a Cu2ZnSn(S,Se)4/CdS interface by a Se&LiF co-selenization process

Hongling Guo et al.

JOURNAL OF MATERIALS CHEMISTRY A (2020)

添加到收藏夹

Article Chemistry, Applied

Lithium-assisted synergistic engineering of charge transport both in GBs and GI for Ag-substituted Cu2ZnSn(S,Se)4 solar cells

Xiangyun Zhao et al.

JOURNAL OF ENERGY CHEMISTRY (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Upper limit to the photovoltaic efficiency of imperfect crystals from first principles

Sunghyun Kim et al.

ENERGY & ENVIRONMENTAL SCIENCE (2020)

添加到收藏夹

Article Energy & Fuels

Mechanism of Current Shunting in Flexible Cu2Zn1-xCdxSn(S,Se)4 Solar Cells

Qiong Yan et al.

SOLAR RRL (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

8% Efficiency Cu2ZnSn(S,Se)4 (CZTSSe) Thin Film Solar Cells on Flexible and Lightweight Molybdenum Foil Substrates

Eunae Jo et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

添加到收藏夹

Article Physics, Condensed Matter

A PL and PLE Study of High Cu Content Cu2ZnSnSe4 Films on Mo/Glass and Solar Cells

M. A. Sulimov et al.

PHYSICS OF THE SOLID STATE (2019)

添加到收藏夹

Article Physics, Applied

Direct evidence of causality between chemical purity and band-edge potential fluctuations in nanoparticle ink-based Cu2ZnSn(S,Se)4 solar cells

S. Campbell et al.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2019)

添加到收藏夹

Article Chemistry, Physical

Lone-pair effect on carrier capture in Cu2ZnSnS4 solar cells

Sunghyun Kim et al.

JOURNAL OF MATERIALS CHEMISTRY A (2019)

添加到收藏夹

Article Energy & Fuels

The electrical and optical properties of kesterites

Maarja Grossberg et al.

JOURNAL OF PHYSICS-ENERGY (2019)

添加到收藏夹

Article Energy & Fuels

Doping and alloying of kesterites

Yaroslav E. Romanyuk et al.

JOURNAL OF PHYSICS-ENERGY (2019)

添加到收藏夹

Article Chemistry, Physical

Complex Interplay between Absorber Composition and Alkali Doping in High-Efficiency Kesterite Solar Cells

Stefan G. Haass et al.

ADVANCED ENERGY MATERIALS (2018)

添加到收藏夹

Article Energy & Fuels

Flexible kesterite Cu2ZnSnS4 solar cells with sodium-doped molybdenum back contacts on stainless steel substrates

Kaiwen Sun et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2018)

添加到收藏夹

Article Chemistry, Applied

First-principles study on the alkali chalcogenide secondary compounds in Cu(In,Ga)Se-2 and Cu2ZnSn(S,Se)(4) thin film solar cells

Xian Zhang et al.

JOURNAL OF ENERGY CHEMISTRY (2018)

添加到收藏夹

Article Chemistry, Physical

Identification of Killer Defects in Kesterite Thin-Film Solar Cells

Sunghyun Kim et al.

ACS ENERGY LETTERS (2018)

添加到收藏夹

Article Chemistry, Physical

High-Efficiency (LixCu1-x)(2)ZnSn(S,Se)(4) Kesterite Solar Cells with Lithium Alloying

Antonio Cabas-Vidani et al.

ADVANCED ENERGY MATERIALS (2018)

添加到收藏夹

Article Chemistry, Physical

Analysis of Failure Modes in Kesterite Solar Cells

Louis Grenet et al.

ACS APPLIED ENERGY MATERIALS (2018)

添加到收藏夹

Article Chemistry, Inorganic & Nuclear

Substitution of Li for Cu in Cu2ZnSnS4: Toward Wide Band Gap Absorbers with Low Cation Disorder for Thin Film Solar Cells

A. Lafond et al.

INORGANIC CHEMISTRY (2017)

添加到收藏夹

Article Energy & Fuels

Influence of the copper content on the optical properties of CZTSe thin films

M. V. Yakushev et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

New Insight of Li-Doped Cu2ZnSn(S,Se)4 Thin Films: Li-Induced Na Diffusion from Soda Lime Glass by a Cation-Exchange Reaction

Yanchun Yang et al.

ACS APPLIED MATERIALS & INTERFACES (2017)

添加到收藏夹

Article Chemistry, Physical

Efficiency Enhancement of Cu2ZnSn(S,Se)4 Solar Cells via Alkali Metals Doping

Yao-Tsung Hsieh et al.

ADVANCED ENERGY MATERIALS (2016)

添加到收藏夹

Article Physics, Applied

Deep Defects in Cu2ZnSn(S,Se)4 Solar Cells with Varying Se Content

S. Levcenko et al.

PHYSICAL REVIEW APPLIED (2016)

添加到收藏夹

Article Chemistry, Multidisciplinary

Engineering Solar Cell Absorbers by Exploring the Band Alignment and Defect Disparity: The Case of Cu- and Ag-Based Kesterite Compounds

Zhen-Kun Yuan et al.

ADVANCED FUNCTIONAL MATERIALS (2015)

添加到收藏夹

Article Chemistry, Physical

Lithium-doping inverts the nanoscale electric field at the grain boundaries in Cu2ZnSn(S,Se)(4) and increases photovoltaic efficiency

H. Xin et al.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2015)

添加到收藏夹

Article Physics, Applied

Examination of electronic structure differences between CIGSSe and CZTSSe by photoluminescence study

Kong Fai Tai et al.

JOURNAL OF APPLIED PHYSICS (2015)

添加到收藏夹

Review Chemistry, Multidisciplinary

Classification of Lattice Defects in the Kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 Earth-Abundant Solar Cell Absorbers

Shiyou Chen et al.

ADVANCED MATERIALS (2013)

添加到收藏夹

Article Physics, Applied

Band tailing and efficiency limitation in kesterite solar cells

Tayfun Gokmen et al.

APPLIED PHYSICS LETTERS (2013)

添加到收藏夹

Article Physics, Applied

Photoluminescence characterization of a high-efficiency Cu2ZnSnS4 device

Talia Gershon et al.

JOURNAL OF APPLIED PHYSICS (2013)

添加到收藏夹

Article Physics, Applied

Admittance spectroscopy of Cu2ZnSnS4 based thin film solar cells

P. A. Fernandes et al.

APPLIED PHYSICS LETTERS (2012)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.