☆ 4.6 Article

Effect of Zn and Cu Addition on Mechanical Properties of As-Extruded Mg-3Sn-1Ca Alloy

MATERIALS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Microstructure and mechanical properties of Mg-3Sn-1Ca reinforced with AlN nano-particles

Shaozhu Wang et al.

Summary: The effects of adding different amounts of AlN nanoparticles on the microstructural evolution and strengthening mechanisms of Mg-3Sn-1Ca based alloys were investigated. It was observed that increasing the amount of AlN nanoparticles led to a significant decrease in grain size. The presence of AlN nanoparticles refined the primary crystal phases and provided more nucleation sites for the formation of magnesium. Additionally, the nanoparticles restricted grain growth during solidification. The addition of AlN nanoparticles resulted in improved tensile properties and hardness at both room temperature and high temperature.

JOURNAL OF MAGNESIUM AND ALLOYS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Segregation-driven exceptional twin-boundary strengthening in lean Mg-Zn-Ca alloys

I Basu et al.

Summary: Twinning-mediated plasticity in hexagonal close-packed crystal structures offers great potential for achieving lean Mg-based alloys with high strength and extended ductility. The effects of Zn and Ca solutes on micropillar deformation and the response of pre-existing twin boundaries to applied stress were assessed. In the presence of Zn and Ca solutes, the micropillars exhibited enhanced strength and ductility due to the periodic segregation of solutes at the twin boundaries. In contrast, pure Mg micropillars showed massive twin growth and basal slip, leading to earlier failure.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure refinement, mechanical and biocorrosion properties of Mg-Zn-Ca-Mn alloy improved by a new severe plastic deformation process

M. Kavyani et al.

Summary: This study investigated the microstructural evolution, mechanical properties, and biocorrosion performance of a Mg-Zn-Ca-Mn alloy under different processing conditions. The results showed that the alloy experienced grain refinement, improved mechanical properties, and enhanced biocorrosion resistance after undergoing the HECAP process. These findings suggest that HECAPed Mg-Zn-Ca-Mn alloy has great potential for biomedical applications.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Outstanding enhancement in critical resolved shear stress of basal slip with precipitation in Mg-10Dy-0.7La alloy: A micro-pillar compression study

U. R. Ghori et al.

Summary: The strengthening effect of precipitates on basal slip in Mg-RE alloys leads to a significant increase in CRSS, which is the highest reported for any alloy. This increase can be rationalized by considering the network of precipitates.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of modified Mg-8Al-2Sn alloys using Zn addition combined with artificial aging treatment

Chen-Yi Ma et al.

Summary: The microstructures and mechanical properties of Mg-8Al-2Sn (AT82) base alloys were improved by adding zinc, which refined the microstructure and promoted age-hardening response, leading to better mechanical properties. The ATZ821 alloy displayed excellent strength and ductility at different temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Al addition on microstructure and mechanical properties of Mg-Gd-Zn alloys

Zhi-bing Ding et al.

Summary: The microstructure evolution and mechanical properties of Mg-15.3Gd-1Zn alloys with different Al contents were investigated. The addition of 0.4 wt.% Al facilitates the formation of 18R-LPSO phase. After homogenization treatment, (Mg,Zn)3Gd, 18R-LPSO and some Al11Gd3 phases are transformed into the high-temperature stable 14H-LPSO phases. The particulate Al-Gd phases can stimulate the nucleation of dynamic recrystallization. The tensile strength of the as-rolled alloys is improved remarkably due to grain refinement and the reinforcement of LPSO phase. The precipitation of the beta' phase in the peak-aged alloys significantly improves the strength. The peak-aged alloy containing 0.4 wt.% Al achieves excellent mechanical properties.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2022)

添加到收藏夹

Review Metallurgy & Metallurgical Engineering

The role and significance of Magnesium in modern day research-A review

S. V. Satya Prasad et al.

Summary: This review paper summarizes the importance of magnesium and its material properties in engineering applications, including the influence of alloying elements on mechanical properties, corrosion behavior, and manufacturing techniques. Additionally, it discusses the recent trends of magnesium alloys, their applications in the biomedical field, and techniques to overcome biocorrosion.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

添加到收藏夹

Article Chemistry, Physical

Compressive Properties and Energy Absorption Characteristics of Extruded Mg-Al-Ca-Mn Alloy at Various High Strain Rates

Chongchen Xiang et al.

Summary: This study focused on the mechanical properties and energy absorption characteristics of extruded Mg-Al-Ca-Mn alloy under high strain rate compression in different compression directions. The alloy exhibited strong strain rate sensitivity, with compressive strength increasing significantly and deformation ability improving with higher strain rates. When compressed along the extrusion direction, the total absorbed energy, crush force efficiency, and specific energy absorption of the Mg-Al-Ca-Mn alloy were greatly improved compared to other compression directions.

MATERIALS (2021)

添加到收藏夹

Article Chemistry, Physical

Characteristics of the Mg-Zn-Ca-Gd Alloy after Mechanical Alloying

Sabina Lesz et al.

Summary: Magnesium-based materials show great potential for medical implants, but proper alloying elements and methods are crucial for enhancement. Mechanical alloying is an effective method for designing alloys with desired structures and properties. The hardness of the materials is found to be correlated with the milling time and particle size during the mechanical alloying process.

MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Stress relaxations during cyclic loading-unloading in precipitation hardened Mg-4.5Zn

Jun Wang et al.

Summary: The study investigates the impact of aging on cyclic loading-unloading responses of extruded Mg-Zn alloys, revealing that aging has complex effects on twinning and slip behavior. Aged samples promote twinning over slip during loading and experience additional 'forward' twinning upon unloading. Furthermore, aging leads to noticeable ratchetting strain compared to non-aged samples.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

In- vitro corrosion behavior of the cast and extruded biodegradable Mg-Zn-Cu alloys in simulated body fluid (SBF)

Mehrab Lotfpour et al.

Summary: In this study, a new biodegradable Mg-Zn-Cu magnesium alloy was introduced for biological applications. Addition of 0.1wt.% Cu was found to enhance corrosion resistance, with extruded alloys displaying better corrosion resistance behavior compared to cast alloys. The Mg-2Zn-0.1Cu alloy was identified as a potential candidate for use as a biodegradable magnesium implant due to its improved tensile properties.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of Zn/Al mass ratio on microstructure evolution and mechanical properties of Mg-Sn based alloys

Yuxiao Luo et al.

Summary: The effects of Zn/Al mass ratio on the microstructure evolution and mechanical properties of the Mg-3Sn-5Zn-xAl (x=0,1,2,3 wt%) alloy were systematically investigated. The addition of Al led to improved tensile yield strength and ultimate tensile strength, but slightly reduced the volume fraction of recrystallized region. The excellent ductility of the extruded alloys was attributed to the activation of non-basal slip systems, high volume fraction of fine DRXed grains, and weakened texture.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced mechanical properties and corrosion resistance of rolled Mg-1.5Sn-0.5Ca alloy by Ce microalloying

Chunming Wang et al.

Summary: The addition of minor cerium refines the microstructure, enhances the strength and ductility of the alloy, and improves its corrosion resistance.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural effects on mechanical properties and degradation behavior of Mg-Cu alloy

Xudong Yan et al.

Summary: The study found that magnesium-copper alloys with low copper content and solid solution treatment exhibit better mechanical properties and corrosion resistance, while alloys with higher copper content are prone to corrosion. The decrease in Mg2Cu phase content in the solid solution treated alloys leads to improved corrosion resistance and better biocompatibility.

MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced precipitation strengthening of extruded Mg-8 wt.%Al-0.5 wt.%Zn (AZ80) magnesium alloy by extension twinning

Guoliang Shi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure and strengthening mechanism of Mg-5.88Zn-0.53Cu-0.16Zr alloy solidified under high pressure

Kun-yu Guo et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion performance, corrosion fatigue behavior and mechanical integrity of an extruded Mg4Zn0.2Sn alloy

Pingli Jiang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of Second Phases on Microstructure, Microhardness, and Corrosion Behavior of Mg-3Sn-(1Ca) Alloys

Chunming Wang et al.

MATERIALS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strain hardening of as-extruded Mg-xZn (x=1, 2, 3 and 4 wt%) alloys

Chaoyue Zhao et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of Y addition on recrystallization and mechanical properties of Mg-6Zn-xY-0.5Ce-0.4Zr alloys

Lizi Liu et al.

VACUUM (2018)

添加到收藏夹

Article Chemistry, Physical

Strengthening effect of nano and micro-sized precipitates in the hot-extruded Mg-5Sn-3Zn alloys with Ca addition

L. L. Chang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of Zn on the microstructure and tensile properties of as-extruded Mg-8A1-2Sn alloy

Hui-Yuan Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Ameliorating the mechanical properties of magnesium alloy: Role of texture

Qinghang Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of Zn/Gd ratio on the microstructures and mechanical properties of Mg-Zn-Gd-Zr alloys

Siqi Yin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Development of high-strength, low-cost wrought Mg-2.0 mass% Zn alloy with high Mn content

Fusheng Pan et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Development of high-strength, low-cost wrought Mg-2.0 mass% Zn alloy with high Mn content

Fusheng Pan et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2016)

添加到收藏夹

Article Thermodynamics

Microstructures and Thermal Properties of Mg-Sn-Ca Alloys: Casts and Extrusions

Jung-Han Kim et al.

INTERNATIONAL JOURNAL OF THERMOPHYSICS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

A new high-strength extruded Mg-8Al-4Sn-2Zn alloy

Sung Hyuk Park et al.

MATERIALS LETTERS (2015)

添加到收藏夹

Article Nanoscience & Nanotechnology

The microstructure, texture and mechanical properties of extruded Mg-5.3Zn-0.2Ca-0.5Ce (wt%) alloy

Y. Z. Du et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhancing mechanical properties of Mg-Sn alloys by combining addition of Ca and Zn

Hucheng Pan et al.

MATERIALS & DESIGN (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Role of hydrogen evolution rate in determining the corrosion rate of extruded Mg-5Sn-(1-4 wt%)Zn alloys

Heon-Young Ha et al.

CORROSION SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Limitations in the use of the potentiodynamic polarisation curves to investigate the effect of Zn on the corrosion behaviour of as-extruded Mg-Zn binary alloy

Heon-Young Ha et al.

CORROSION SCIENCE (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of lattice parameter changes on critical resolved shear stress and mechanical properties of magnesium binary single crystals

Hyung Lae Kim et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of Mg-6Zn-xCu-0.6Zr (wt.%) alloys

H. M. Zhu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of the Zn content on the microstructure and mechanical properties of indirect-extruded Mg-5Sn-xZn alloys

W. N. Tang et al.

MATERIALS & DESIGN (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effective values of critical resolved shear stress for slip in polycrystalline magnesium and other hcp metals

W. B. Hutchinson et al.

SCRIPTA MATERIALIA (2010)

添加到收藏夹

Review Materials Science, Multidisciplinary

Predicting grain refinement by cold severe plastic deformation in alloys using volume averaged dislocation generation

Marco J. Starink et al.

ACTA MATERIALIA (2009)

添加到收藏夹

Article Engineering, Industrial

Hot workability characteristics of cast and homogenized Mg-3Sn-1Ca alloy

K. P. Rao et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)

添加到收藏夹

Article Nanoscience & Nanotechnology

Solid-solution hardening and softening in Mg-Zn alloys

A. H. Blake et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Mg-Al-Ca-Nd alloys fabricated by gravity casting and extrusion process

Hyeon-Taek Son et al.

MATERIALS TRANSACTIONS (2008)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of precipitate shape and orientation on dispersion strengthening in magnesium alloys

JF Nie

SCRIPTA MATERIALIA (2003)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.