☆ 4.3 Article

Microstructure and Mechanical Properties of the Bimetallic Wire Arc Additively Manufactured Structure (BAMS) of SS304L and SS308L Fabricated by Hybrid Manufacturing Process

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Effect of Welding Speed on Microstructure and Anisotropic Properties of Wire-Arc Additive-Manufactured Ti-6Al-4V alloy

Guo Xian et al.

Summary: In this study, the effect of welding speed on the grain structure and tensile strength of Ti64 alloy was investigated through experiments and numerical simulations. It was found that a faster welding speed resulted in more equiaxed grains and lower anisotropic tensile strength, while slower welding speeds led to slower grain formation and more complex shapes.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Additive manufacturing of Ti-Ni bimetallic structures

Ali Afrouzian et al.

Summary: Bimetallic structures of nickel and commercially pure titanium were successfully manufactured through directed energy deposition metal additive manufacturing, exhibiting different mechanical properties in different configurations. The formation of intermetallic NiTi phase at the interface was confirmed, and a microstructural gradient was observed in the heat-affected zone. The longitudinal and transverse samples showed significant differences in elongation, with the longitudinal samples demonstrating brittle fracture failure during compressive deformation, while the transverse samples exhibited ductile failure.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Heat Treatment on the Mechanical Behavior of Udimet 720 Nickel-Based Superalloy

Yu Sik Kong et al.

Summary: The microstructure formation of nickel-based superalloys significantly affects their mechanical properties, especially the presence and characteristics of the γ' phase. This study investigates the influence of heat treatment conditions on the microstructural and mechanical properties of Udimet 720. The results show that thermal exposure alters the microstructure, leading to a deterioration in the tensile and creep-rupture properties of the alloy.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

添加到收藏夹

Article Chemistry, Physical

EFFECT OF DIFFERENT MIG WELDING MODES ON HARD-FACING OF INCONEL 718 ON 321 STAINLESS STEEL

Karpagaraj Anbalagan et al.

Summary: In this study, the metal inert gas (MIG) welding process was used to deposit Inconel 718 on 321 stainless steel. Different modes and parameters were tested to find the optimal MIG welding mode. The results showed that the DC-pulsed mode was qualified for making the metal deposition, and defect-free 2-mm-thick layer depositions were successfully achieved on the 321 stainless steel surfaces.

SURFACE REVIEW AND LETTERS (2022)

添加到收藏夹

Review Engineering, Manufacturing

Additive manufacturing of bimetallic structures

Amit Bandyopadhyay et al.

Summary: Bimetallic structures are in high demand for current industrial applications due to their unique properties. However, welding techniques face challenges in joining dissimilar metals, leading to heat-affected zone management and brittle intermetallic phase issues. Metal additive manufacturing (AM) has emerged as a promising solution for processing bimetallic structures. This review provides insights into various processing strategies, challenges, and future directions for the implementation of AM technologies in bimetallic structures.

VIRTUAL AND PHYSICAL PROTOTYPING (2022)

添加到收藏夹

Article Engineering, Manufacturing

An experimental investigation and neuro-fuzzy modeling to ascertain metal deposition parameters for the wire arc additive manufacturing of Incoloy 825

Bharat Kumar Chigilipalli et al.

Summary: Additive manufacturing is a critical technology for repairing, rebuilding, and rapidly manufacturing major components. In this study, the wire arc additive manufacturing technique using metal inert gas welding was experimented on Incoloy 825, proving it to be a cost-effective method for producing large-scale parts. The effects of input parameters on bead geometry were analyzed, and a neural fuzzy inference system was implemented for predicting geometrical characteristics. The results showed that the subtractive clustering fuzzy inference model performed the best in predicting the deposited bead geometry as a function of process parameters. The study also successfully constructed a single-pass multi-layer wall of Incoloy 825 using the identified optimum parameters, demonstrating the high quality of the built structure.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of joint interface on mechanical properties in dissimilar friction welds

Muralimohan Cheepu et al.

Summary: Friction welding is a solid-state joining process that provides sound welds without cracks. In this study, the dissimilar join of austenitic stainless steel to high tensile alloy steel was achieved using friction welding. The thickness of the intermixing zone in the welds was found to have an effect on the mechanical properties.

ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wire and arc additive manufacturing: Opportunities and challenges to control the quality and accuracy of manufactured parts

Davoud Jafari et al.

Summary: Wire and arc additive manufacturing (WAAM) is capable of producing medium to large components with high-rate deposition and potentially unlimited build size, requiring optimized process planning for uniform, defect-free deposition. This technology has shifted from a prototyping technique to a viable and cost-effective production method, emphasizing dimensional precision and surface finish for manufactured components.

MATERIALS & DESIGN (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Wire and arc additive manufacturing of 308L stainless steel components: Optimization of processing parameters and material properties

Van Thao Le et al.

Summary: The study focuses on wire and arc additive manufacturing (WAAM) of thin-walled 308L stainless steel components, investigating the influence of welding parameters on weld bead geometry and optimizing these parameters for the deposition of 308L steel walls. The microstructure and mechanical properties of WAAM 308L steel walls were explored, showing desirable geometry of single weld beads and adequate mechanical properties for industrial applications.

ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2021)

添加到收藏夹

Article Engineering, Industrial

An innovative process combination of additive manufacturing and sheet bulk metal forming for manufacturing a functional hybrid part

Marion Merklein et al.

Summary: The paper introduces the combination of additive manufacturing and forming technologies, demonstrating the potential of this process combination. By using PBF-LB/M for tooth geometry manufacturing and forming, closer results to the target were achieved, saving manufacturing costs and improving production efficiency.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Automation & Control Systems

Microstructure, mechanical behavior, and crystallographic texture in a hot forged dual-phase stainless steel

Riad Badji et al.

Summary: The study investigated the hot forging behavior of a dual phase stainless steel in the temperature range of 850-1250 degrees C, revealing the effects on cracking phenomenon, grain boundary types, and mechanical properties. Higher forging temperatures improved the steel's plasticity and overall mechanical properties.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Dry sliding wear behavior of Inconel 718 additively manufactured by DMLS technique

V. Anandakrishnan et al.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2020)

添加到收藏夹

Article Automation & Control Systems

Tensile properties and microstructural features of 304L austenitic stainless steel produced by wire-and-arc additive manufacturing

Vittoria Laghi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Influence of Friction Pressure on Microstructure and Joining Phenomena of Dissimilar Joints

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructural Characteristics of Wire Arc Additive Manufacturing with Inconel 625 by Super-TIG Welding

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Interface Microstructure Characteristics of Friction-Welded Joint of Titanium to Stainless Steel with Interlayer

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Welding Parameters on TIG Welding of Inconel 718 to AISI 4140 Steel

M. Anuradha et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

添加到收藏夹

Article Engineering, Industrial

Hybrid manufacturing of components from Ti-6Al-4V by metal forming and wire-arc additive manufacturing

M. Bambach et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced interface strength in steel-nickel bimetallic component fabricated using wire arc additive manufacturing with interweaving deposition strategy

Bintao Wu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of TA15-Ti2AlNb bimetallic structures by laser additive manufacturing

Yantao Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Experimental investigations on the effect of wire arc additive manufacturing process parameters on the layer geometry of Inconel 825

Bharat C. H. Kumar et al.

MATERIALS TODAY-PROCEEDINGS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Predicting microstructure and strength for AISI 304L stainless steel forgings

N. T. Switzner et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Friction Welding of Titanium to Stainless Steel Using Al Interlayer

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2019)

添加到收藏夹

Proceedings Paper Engineering, Mechanical

Additive manufacturing of metal components - process-material interaction in different process chains

H. N. Hansen et al.

40TH RISO INTERNATIONAL SYMPOSIUM ON MATERIALS SCIENCE: METAL MICROSTRUCTURES IN 2D, 3D AND 4D (2019)

添加到收藏夹

Review Engineering, Manufacturing

Hybrid Processes in Additive Manufacturing

Michael P. Sealy et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Analysis and Characterization of the Role of Ni Interlayer in the Friction Welding of Titanium and 304 Austenitic Stainless Steel

C. H. Muralimohan et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)

添加到收藏夹

Article Engineering, Manufacturing

A review of process development steps for new material systems in three dimensional printing (3DP)

Ben Utela et al.

Journal of Manufacturing Processes (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.