☆ 4.7 Article

Microstructure evolution, mechanical properties and strengthening mechanisms in the hot extruded Si3N4 particle reinforced Al-Cu-Mg composite

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

Unprece dente d age-hardening and its structural requirement in a severely deformed Al-Cu-Mg alloy

Ran Yang et al.

Summary: A gradient nanostructured surface layer was produced in an Al-Cu-Mg alloy through surface sliding friction treatment at liquid nitrogen temperature, achieving unprecedented age-hardening after aging treatment with microhardness values exceeding previous maximum values. Enhanced grain boundary segregation instead of precipitation is believed to be responsible for this substantial age-hardening.

SCRIPTA MATERIALIA (2022)

添加到收藏夹

Article Engineering, Mechanical

Study fatigue crack initiation in TiB2/Al-Cu-Mg composite by in-situ SEM and X-ray microtomography

Jiwei Geng et al.

Summary: The study found that fatigue cracks in particle-reinforced aluminium matrix composites mostly initiate at multiple sites associated with TiB2 and second phases (S/θ), and only a few cracks are caused by matrix fracture close to high density dislocation zones around TiB2. The growth capability of initiated cracks depends on their stress intensity factors at the crack tip, with only cracks initiated from the largest-sized (S/θ + TiB2) cluster developing into main cracks. During main crack evolution, small cracks grow along slip traces and are hindered by grain boundaries and/or TiB2.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Powder assembly & alloying to CNT/Al-Cu-Mg composites with trimodal grain structure and strength-ductility synergy

Xiaowen Fu et al.

Summary: A novel strategy of powder assembly & alloying was used to achieve a trimodal grain structure in carbon nanotubes (CNTs) reinforced aluminum matrix composites, resulting in superior strength-ductility synergy. This method proved to be an effective way to design and fabricate heterogeneous structured metal matrix nanocomposites.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Fabrication of fine grain structures in Al matrices at elevated temperature by the stimulation of dual-size particles

Jun Liu et al.

Summary: This study introduces particles of different sizes into aluminum matrices to achieve fine grain structures at elevated temperatures. Compared to alloy counterparts, composites show more rapid and obvious grain refinement.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties of the electron-beam welded joints of cast Al-Cu-Mg-Ag alloy

Jian Wang et al.

Summary: The microstructures, hardness distribution and strengthening mechanisms of the electron-beam welded joints of cast Al-Cu-Mg-Ag alloy plate were investigated. It was found that the precipitation of fine Omega, theta' plates and dispersed precipitates after post-welding heat treatment is the main reason for the increase in strength of the welded joint.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Synthesis and Characterization of Silicon Nitride Reinforced Al-Mg-Zn Alloy Composites

G. Anbuchezhiyan et al.

Summary: In this study, aluminium metal matrix composite reinforced with hard silicon nitride (Si3N4) particles was experimentally synthesized using squeeze casting technique. The inclusion of Si3N4 significantly improved the mechanical behavior, corrosion resistance, and wear resistance of the synthesized composites, as observed through various tests. Scanning Electron microscope micrograph of worn surfaces revealed deep grooving associated with abrasive wear due to the presence of Si3N4.

METALS AND MATERIALS INTERNATIONAL (2021)

添加到收藏夹

Article Chemistry, Physical

Preparation of in-situ AlN-TiC nanoparticles and their refinement and reinforcement effects on Al-Zn-Mn-Cu alloy

Yuhang Xia et al.

Summary: This study improved the distribution of AlN and TiC nanoparticles in the matrix by preparing AlN-TiC/Al composite ribbons and adding them to an Al-Zn-Mn-Cu alloy, leading to a significant enhancement in the mechanical properties of the composite.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructures and Tensile Fracture Behavior of 2219 Wrought Al-Cu Alloys with Different Impurity of Fe

Daofen Xu et al.

Summary: The presence of Fe-rich intermetallic phases in Al-Cu alloy can significantly affect its mechanical properties, particularly reducing its ductility. The size and quantity of these phases increase with higher Fe content, leading to a decrease in elongation without much effect on ultimate tensile strength and yield strength.

METALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Precipitate/matrix incompatibilities related to the {111}Al ω plates in an Al-Cu-Mg-Ag alloy

M. R. Gazizov et al.

Summary: The atomic structure of omega plates forming on {111}Al planes in an Al-Cu-Mg-Ag alloy has been investigated, revealing volumetric and structural incompatibilities with the Al matrix. Different thicknesses of omega plates were studied under peak-aged conditions, showing shear components and misfit strains affecting plate interfaces and the thickening of omega precipitates.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Investigation on peripheral coarse grains and precipitation behavior of in-situ TiB2/Al-Cu-Mg composites with various Mg contents

Liang Chen et al.

Summary: The study found that Mg content strongly influences the microstructure and mechanical properties of TiB2 reinforced Al-Cu-Mg composites. Increasing Mg content results in deeper fine dynamic recrystallized grains on the surface and improved mechanical properties, but excessive Mg content can lead to the formation of precipitation free zones, ultimately reducing hardness and ultimate tensile strength.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

Precipitation-hardness map for Al-Cu-Mg alloy (AA2024-T3)

V. A. Esin et al.

Summary: The precipitation map of Al-Cu-Mg alloy (AA2024-T3) was obtained by combining differential scanning calorimetry analysis and high-resolution transmission electron microscopy observations, revealing the appearance of equilibrium S-Al2CuMg phase at 85 degrees C after 1000 h of ageing. Hardness values showed that the maximum hardness was located at the boundary between S-phase + GPB zones and S-phase regions for all studied temperatures.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced grain refinement and mechanical properties of a high-strength Al-Zn-Mg-Cu-Zr alloy induced by TiC nano-particles

Kai Zhao et al.

Summary: The addition of TiC nano-particles in high-strength aluminum alloy 7050 leads to significant grain refinement and improved mechanical properties through growth restriction effect and heterogeneous nucleation. The alignment of TiC nano-particles along extrusion direction after subsequent heat treatment contributes to the enhanced tensile properties, ductility, and refined precipitates in the composite. These synergistic effects result in optimized mechanical properties of TiCp/7050 composite, providing new insights for controlling matrix grains of Zr-containing Al alloys and developing low-cost Al matrix composites.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

Strengthening and Weakening Effects of Particles on Strength and Ductility of SiC Particle Reinforced Al-Cu-Mg Alloys Matrix Composites

Zhiyu Yang et al.

Summary: The study examines the impact of SiC particles on the strength and ductility of composite materials, using different mechanical properties of Al-Cu-Mg alloy matrices and manufacturing composites in 18 combinations. The critical particle size for optimal ductility was identified, and the strengthening limit and match range for effective strengthening were defined based on particle size and matrix strength. This research provides valuable insights for optimizing the mechanical properties of particle-reinforced metal matrix composites.

MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Good combination of strength and corrosion resistance in an Al-Cu-Mg alloy processed by a short-cycled thermomechanical treatment

L. Mei et al.

Summary: The research found that the warm rolled alloy showed significant improvement in strength and corrosion resistance after appropriate aging, with good ductility. This improvement was mainly attributed to a more homogeneous distribution of nanosized precipitates in the grain interior and the absence of continuous grain boundary precipitates.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Chemistry, Physical

The role of Si on microstructure, mechanical and local corrosion behaviors of an Al-Cu-Mg-Si alloy with high Cu/Mg ratio

Fushan Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of non-isothermal aging on mechanical properties, corrosion behavior and microstructures of Al-Cu-Mg-Si alloy

Xin Zhan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

The effect of pre-deformation on the precipitation behavior of AlCuMg(Si) alloys with low Cu/Mg ratios

F. J. Niu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

The synergetic effect of Si and Sc on the thermal stability of the precipitates in AlCuMg alloy

S. S. Liang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Chemistry, Physical

Improvement of anisotropic tensile properties of Al-7.9Zn-2.7Mg-2.0Cu alloy sheets by particle stimulated nucleation

Qianhao Zang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Effect of T-phase on microstructure of the hot rolled Al-Cu-Mg alloy

Fei Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Dynamic dissolution and texture evolution of an Al-Cu-Mg-Ag alloy during hot rolling

Fei Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructures and mechanical properties of an Al-Cu-Mg-Sc alloy reinforced with in-situ TiB2 particulates

Siming Ma et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

The role of Sn element on the deformation mechanism and precipitation behavior of the Al-Cu-Mg alloy

Shuai Dai et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Achieving highly strengthened Al-Cu-Mg alloy by grain refinement and grain boundary segregation

Takahiro Masuda et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced Brass texture of hot-rolled Al-4Cu-1.6Mg alloy by 0.1% Zr addition

Qi Zhao et al.

MATERIALS CHARACTERIZATION (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of nanosized TiCp dispersion on the high-temperature tensile strength and ductility of in situ TiCp/Al-Cu-Mg-Si nanocomposites

Yu-Yang Gao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Chemistry, Physical

Tuning the microstructure features of in-situ nano TiB2/Al-Cu-Mg composites to enhance mechanical properties

Jiwei Geng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructural evolution and strengthening mechanisms operating during cryogenic rolling of solutionized Al-Cu-Mg alloy

Ivan S. Zuiko et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

High-temperature mechanical properties of 2024 Al matrix nanocomposite reinforced by TiC network architecture

Huabing Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Precipitation behavior in an Al-Cu-Mg-Si alloy during ageing

Marat Gazizov et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Simultaneously improving strength and ductility for Al-Cu-Mg alloy via threadiness array of TiC nanoparticles

Huabing Yang et al.

MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Novel preparation of Al-5%Cu / BN and Si3N4 composites with analyzing microstructure, thermal and mechanical properties

A. Lotfy et al.

MATERIALS CHARACTERIZATION (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

The response of room temperature and high temperature tensile properties to the microstructure variation of an AlN + Si3N4/Al composite by heat treatment

Qingfei Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Chemistry, Physical

Morphologies, orientation relationships, and evolution of the T-phase in an Al-Cu-Mg-Mn alloy during homogenisation

Y. Q. Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Chemistry, Physical

Particulate metal matrix composites development on the basis of in situ synthesis of TiC reinforcing nanoparticles during mechanical alloying

V. A. Popov et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Recrystallization behavior of multi-directionally forged over-aged and solution treated Al-Cu-Mg alloy during non-isothermal annealing

Saeed Khani Moghanaki et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multi-scale study of microstructure evolution in hot extruded nano-sized TiB2 particle reinforced aluminum composites

Z. Chen et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Toughening of aluminum matrix nanocomposites via spatial arrays of boron carbide spherical nanoparticles

Lin Jiang et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interfacial characteristics of diamond/aluminum composites with high thermal conductivity fabricated by squeeze-casting method

Longtao Jiang et al.

MATERIALS CHARACTERIZATION (2015)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of pre-straining on the aging behavior and mechanical properties of an Al-Cu-Mg-Ag alloy

M. Gazizov et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Chemistry, Physical

Crystal substructures of the rotation-twinned T (Al20Cu2Mn3) phase in 2024 aluminum alloy

Z. Q. Feng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

添加到收藏夹

Article Nanoscience & Nanotechnology

Development of TiB2 reinforced aluminum foundry alloy based in situ composites - Part II: Enhancing the practical aluminum foundry alloys using the improved Al-5 wt%TiB2 master composite upon dilution

Tongmin Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanical properties of in-situ TiB2/A356 composites

Mingliang Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Precipitation of partially coherent α-Al(Mn,Fe)Si dispersoids and their strengthening effect in AA 3003 alloy

Y. J. Li et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and tensile properties of Si3N4p/2024Al composite fabricated by pressure infiltration method

Ziyang Xiu et al.

MATERIALS & DESIGN (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and properties characteristic during interrupted multi-step aging in Al-Cu-Mg-Ag-Zr alloy

Zhu Baohong et al.

RARE METALS (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

A conventional thermo-mechanical process of Al-Cu-Mg alloy for increasing ductility while maintaining high strength

Y. J. Huang et al.

SCRIPTA MATERIALIA (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanical behavior of ultrafine-grained Al composites reinforced with B4C nanoparticles

Zhihui Zhang et al.

SCRIPTA MATERIALIA (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

The mechanical properties of co-continuous Si3N4/Al composites manufactured by squeeze casting

Yuan Lu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of Al-Cu-Mg-Mn-Zr alloy with trace amounts of Ag

Xiao Yan Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dispersoid precipitation and process modelling in zirconium containing commercial aluminium alloys

JD Robson et al.

ACTA MATERIALIA (2001)

添加到收藏夹

Article Materials Science, Multidisciplinary

Coexistence of clusters, GPB zones, S-, S′- and S-phases in an Al-0.9% Cu-1.4% Mg alloy

A Charai et al.

ACTA MATERIALIA (2000)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical behavior of 6061Al reinforced with silicon nitride particles, processed by powder metallurgy

V Amigó et al.

SCRIPTA MATERIALIA (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.