相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Overview of Foreign Boiler Designs for Ultra Supercritical (USC) Boilers and Prospects for Development of USC Power Units in Russia
E. V. Somova et al.
THERMAL ENGINEERING (2021)
Experimental study on creep-fatigue behaviors of chinese P92 steel with consideration of several important factors
Jianfeng Mao et al.
INTERNATIONAL JOURNAL OF FATIGUE (2021)
Microstructural features and mechanical properties of similar and dissimilar ferritic welded joints for ultra-supercritical power plants
Nitin Saini et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2021)
Characterization of the cyclic softening and remaining creep behaviour of P92 steel weldment
Wei Zhang et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)
Perspectives for 700 °C ultra-supercritical power generation: Thermal safety of high-temperature heating surfaces
Zhongxiao Zhang et al.
ENERGY (2020)
Microstructural characteristics and low cycle fatigue properties at 230 °C of different weld zone materials from a 100 mm thick dissimilar weld of ultra-supercritical rotor steel
Jian Long et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Effect of post-weld heat treatment on the microstructure and hardness of P92 steel in IN740H/P92 dissimilar weld joints
Wi-Geol Seo et al.
MATERIALS CHARACTERIZATION (2020)
Two stress rupture modes observed in Alloy 617-9%Cr dissimilar welded joint
Kai Ding et al.
MATERIALS LETTERS (2020)
On the microstructural evolution in 12% Cr turbine steel during low cycle fatigue at elevated temperature
Y. Rae et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Failure competition behavior of 9Cr/617 dissimilar welded joint during LCF test at elevated temperature
Yaqi Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Effect of strain rate induced M23C6 distribution on cyclic deformation behavior: Cyclic hardening model
Haizhou Li et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
Near-threshold fatigue crack growth behavior of 10% Cr martensitic steel welded joint with 9% Cr weld metal in high temperature air
Qixing Sun et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Investigation on the tensile deformation mechanisms in a new Ni-Fe-base superalloy HT700T at 750 °C
P. Zhang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Analysis of the Explosion of Dissimilar Steel Joints in the 1050MW USC Boiler
Qingxu Yang et al.
2020 4TH INTERNATIONAL CONFERENCE ON ELECTRICAL, AUTOMATION AND MECHANICAL ENGINEERING (2020)
Elevated temperature fatigue behaviour of structural materials for advanced ultra supercritical application
Aritra Sarkar et al.
MATERIALS AT HIGH TEMPERATURES (2019)
Creep rupture properties of dissimilar metal weld between Inconel 617B and modified 9%Cr martensitic steel
Yu Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Investigation of Early Cracking of Dissimilar Metal Welds in a 1000-MW Ultra-supercritical Power Plant Close to the Sea
Xiumin Ren et al.
JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2019)
Effect of Cr content on the microstructural stability and impact-toughness evolution of a Ni-Fe-based weld metal
Dong Wu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Transition and fracture shift behavior in LCF test of dissimilar welded joint at elevated temperature
Xiongfei Wang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)
Microstructure and mechanical performance of welded joint between a novel heat-resistant steel and Inconel 617 weld metal
Yu Zhang et al.
MATERIALS CHARACTERIZATION (2018)
Transition of creep damage region in dissimilar welds between Inconel 740H Ni-based superalloy and P92 ferritic/martensitic steel
Kyeong-Yong Shin et al.
MATERIALS CHARACTERIZATION (2018)
Effect of microstructural features on hardness in simulated heat affected zone of an advanced low-alloyed steel
Z. S. Yu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Fatigue Crack Growth Behavior of a New Type of 10% Cr Martensitic Steel Welded Joints with Ni-Based Weld Metal
Qunbing Zhang et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)
Low-cycle fatigue behaviors of a new type of 10% Cr martensitic steel and welded joint with Ni-based weld metal
Qunbing Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2016)
In-situ SEM study of short fatigue crack propagation behavior in a dissimilar metal welded joint of nuclear power plant
Yi-Bo Shang et al.
MATERIALS & DESIGN (2015)
Methodology for fatigue crack growth testing under large scale yielding conditions on corner-crack specimens
Christoph Schweizer et al.
ENGINEERING FRACTURE MECHANICS (2014)
Creep-fatigue damage for a structure with dissimilar metal welds of modified 9Cr-1Mo steel and 316L stainless steel
Hyeong-Yeon Lee et al.
INTERNATIONAL JOURNAL OF FATIGUE (2007)