☆ 4.4 Article

Correlation Between Tribological and Vibration Behaviors in Sliding Lubricated Contacts

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Tribological Characteristics and Load-Sharing of Point-Contact Interface in Three-Body Mixed Lubrication

Jeng-Haur Horng et al.

Summary: This study developed an analysis framework to investigate the contact characteristics in 3-body mixed lubrication. The study found that in mixed lubrication, the values of real contact area, film thickness, contact mode, and solid contact load in 3-body contact were larger than those in ideal 2-body contact. These values increased with an increasing particle size or density.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2022)

添加到收藏夹

Article Engineering, Mechanical

Vibration-based monitoring and prediction of surface profile change and pitting density in a spur gear wear process

Ke Feng et al.

Summary: This paper proposes a methodology for monitoring and predicting gear wear by simulating dynamic responses and estimating wear depth and pitting density. The approach ensures accuracy through model updating, allowing continuous simulation of gear tooth profile changes and pitting density.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2022)

添加到收藏夹

Article Engineering, Mechanical

Transition of the friction behaviour and contact stiffness due to repeated high-pressure contact and slip

S. Fukagai et al.

Summary: This study investigates the running-in process between the wheel and rail using ultrasound reflectometry and high-pressure torsion test approach. Four interfaces with different initial topographies were continuously monitored until they became conformal. A mechanistic model for the running-in process was proposed based on the experimental results. These findings are important for understanding and managing the running-in process of the wheel-rail interface.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Article Engineering, Geological

Influence of iron oxide coating on the tribological behavior of sand grain contacts

Jing Ren et al.

Summary: Research shows that artificially coating sand grains with iron oxides significantly alters the roughness and hardness of the grains, affecting inter-particle friction and normal contact stiffness. The friction coefficient of the coated specimens clearly depends on the magnitude of normal load and loading history, likely due to factors such as contact breakage, plowing damage, and surface debris buildup.

ACTA GEOTECHNICA (2022)

添加到收藏夹

Article Engineering, Mechanical

Correlation Between Friction Coefficient and Friction Vibration in Running-In Process Based on Cross Recurrence Plots

Yuankai Zhou et al.

Summary: This study investigates the correlation between friction coefficient and vibration signals in a friction system using running-in friction tests and cross recurrence plots (CRPs). The results show a strong correlation between friction coefficient and vibration signals, with the strongest correlation occurring under boundary lubrication.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2022)

添加到收藏夹

Article Engineering, Manufacturing

Experimental study on cutting force in ultrasonic vibration-assisted turning of 304 austenitic stainless steel

Yingshuai Xu et al.

Summary: This paper discusses the generation mechanism of cutting force in ultrasonic vibration assisted turning (UAT) and establishes a cutting force model based on the mechanism of UAT. A force measuring test system is designed and contrast experiments for stainless steel workpieces are conducted to analyze the influence of ultrasonic vibration and technological parameters on cutting force. It is found that ultrasonic vibration significantly reduces cutting force, and cutting parameters play a crucial role in controlling the machining process.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2021)

添加到收藏夹

Article Engineering, Industrial

Evaluation of friction reduction and frictionless stress in ultrasonic vibration forming process

Jun Lin et al.

Summary: This study investigates the contact interface friction, its reduction, and the frictionless stress in ultrasonic vibration assisted forming process using experimental, analytical, and numerical methods. It is found that applying oscillation and reducing the diameter-to-height ratio can significantly lessen the flow stress by reducing friction. The relation among experimental/apparent stress, strain, and friction coefficient can be used to predict the friction coefficient and real/frictionless stress.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Scale and surface morphology effects on the micromechanical contact behavior of granular materials

Chitta Sai Sandeep et al.

Summary: The study found that the normal and tangential stiffness of glass specimens increased with increasing grain diameter, but decreased with increasing equivalent surface roughness. Interface friction increased with increasing equivalent surface roughness, but was not heavily dependent on grain size. Rough interfaces had extended slip displacements, resulting in slower degradation of stiffness.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Mechanical

Investigation of friction and vibration performance of lithium complex grease containing nano-particles on rolling bearing

Can Wu et al.

Summary: This paper presents a comparative study of the tribological and vibration performance of synthesized lithium complex grease containing Carbon black, Fe3O4 and Al2O3 nanoparticles on rolling bearing. The results show that the presence of nanoparticles improves friction and wear behavior, with Al2O3 nanoparticles demonstrating the best tribological performance due to their high hardness, cylindrical shape, and deposition on the worn surface. Additionally, the wettability test indicates that Al2O3 nanoparticles can effectively promote base oil flow on the grease soap fibers, resulting in the most effective bearing vibration suppression.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Manufacturing

Analytical prediction of shear angle and frictional behaviour in vibration-assisted cutting

Wei Bai et al.

Summary: Vibration-assisted cutting (VAC) technology improves the machinability of difficult-to-cut materials by analyzing kinematic parameters and shear angle variation, predicting key parameters during the cutting process, and enriching the theory of VAC process.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Engineering, Manufacturing

Effect of ultrasonic and low frequency vibrations on friction coefficient at die radius in deep drawing process

Lijun Wu et al.

Summary: The study investigates the reduction of friction between the sheet metal and die during deep drawing through ultrasonic vibration (UV) and low frequency vibration (LFV). New theoretical models were proposed, and the mechanism of reducing the macroscopic friction coefficient was explored. Testing showed that UV conditions resulted in higher reduction ratios of the macroscopic friction coefficient, but also caused more wear and adhesion compared to LFV conditions.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Engineering, Mechanical

Vibration signatures in ball bearings as a function of lubricant viscosity ratio κ, under alternating lubrication conditions

Morten Opprud Jakobsen et al.

Summary: This paper analyzes the vibrations emitted by a set of grease lubricated ball bearings run under load, when lubrication conditions alternate between good and insufficient. The study shows a good correlation between the lubrication ratio κ and spectral kurtosis for a given frequency band, both when the bearing is new and when κ is below 0.6.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Mechanical

Study of wear particles formation at single asperity contact: An experimental and numerical approach

M. A. Mekicha et al.

Summary: This study investigates the friction and wear behavior of a single roll asperity sliding through a sheet metal using a micro-mechanical experimental approach and material point method (MPM) scratch simulations. It reveals that ploughing is the dominant wear mechanism under lubricated conditions, while wedge forming is the main wear mechanism in the absence of lubricant. The influence of chrome plating on reducing wear particles formation is attributed to its interaction with the lubricant, with almost all frictional resistance arising from deforming the substrate in lubricated contact.

WEAR (2021)

添加到收藏夹

Article Engineering, Mechanical

Wear and vibration behavior of ZDDP-Containing oil considering scuffing failure

Shin-Yuh Chern et al.

Summary: The study demonstrates that the presence of ZDDP additives and the running-in process can effectively increase scuffing load, with relatively small differences in wear curves and lower wear losses compared to lubricants without ZDDP. Therefore, the factors affecting friction failure due to ZDDP need to be fully considered.

WEAR (2021)

添加到收藏夹

Article Engineering, Mechanical

Diagnosis of Liner Scuffing Fault of a Diesel Engine via Vibration and Acoustic Emission Analysis

Sangharatna M. Ramteke et al.

JOURNAL OF VIBRATION ENGINEERING & TECHNOLOGIES (2020)

添加到收藏夹

Article Education, Scientific Disciplines

Investigation of gear pitting defect using vibration characteristics in a single-stage gearbox

Pavankumar Ravindra Sonawane et al.

INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING EDUCATION (2020)

添加到收藏夹

Review Engineering, Manufacturing

Ultrasonic vibration-assisted (UV-A) manufacturing processes: State of the art and future perspectives

Fuda Ning et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Article Engineering, Mechanical

Influence of lubricant on nonlinear vibration characteristics of linear rolling guideway

Yasunori Sakai et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Finite Element Analysis on Ultrasonic Drawing Process of Fine Titanium Wire

Shen Liu et al.

METALS (2020)

添加到收藏夹

Article Engineering, Mechanical

Experimental investigation on identifying friction state in lubricated tribosystem based on friction-induced vibration signals

Pengfei Xing et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2020)

添加到收藏夹

Article Chemistry, Physical

The Friction-Induced Vibration of Water-Lubricated Rubber Bearings during the Shutdown Process

Guangwu Zhou et al.

MATERIALS (2020)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

An experimental investigation of the microslip displacement of geological materials

C. S. Sandeep et al.

COMPUTERS AND GEOTECHNICS (2019)

添加到收藏夹

Article Acoustics

Full finite element models and reduction strategies for the simulation of friction-induced vibrations of rolling contact systems

Van-Vuong Lai et al.

JOURNAL OF SOUND AND VIBRATION (2019)

添加到收藏夹

Article Engineering, Mechanical

A correlation coefficient based vibration indicator for detecting natural pitting progression in spur gears

Pradeep Kundu et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

添加到收藏夹

Article Engineering, Mechanical

Effect of Normal Contact Vibration on Nano-Scale Friction

Jae Hyeok Choi et al.

LUBRICANTS (2019)

添加到收藏夹

Article Engineering, Mechanical

Estimation of the Normal Contact Stiffness for Frictional Interface in Sticking and Sliding Conditions

Davide Tonazzi et al.

LUBRICANTS (2019)

添加到收藏夹

Article Engineering, Mechanical

Tribological and Vibration Studies on Newly Developed Nanocomposite Greases Under Boundary Lubrication Regime

Jayant Singh et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2018)

添加到收藏夹

Article Engineering, Mechanical

Effects of lateral harmonic vibrations on film thickness in EHL point contacts

Josef Fryza et al.

TRIBOLOGY INTERNATIONAL (2018)

添加到收藏夹

Article Engineering, Mechanical

Grain-scale mechanics of quartz sand under normal and tangential loading

C. S. Sandeep et al.

TRIBOLOGY INTERNATIONAL (2018)

添加到收藏夹

Article Engineering, Mechanical

Validation of a new frictional law for simulating friction-induced vibrations of rough surfaces

G. Lacerra et al.

TRIBOLOGY INTERNATIONAL (2018)

添加到收藏夹

Article Engineering, Manufacturing

Analysis of friction reduction effect due to ultrasonic vibration exerted in friction stir welding

C. L. Yang et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

添加到收藏夹

Article Engineering, Mechanical

Investigation into the influence of particles' friction coefficient on vibration suppression in gear transmission

Wangqiang Xiao et al.

MECHANISM AND MACHINE THEORY (2017)

添加到收藏夹

Article Engineering, Mechanical

Parametrical experimental and numerical analysis on friction-induced vibrations by a simple frictional system

M. Di Bartolomeo et al.

TRIBOLOGY INTERNATIONAL (2017)

添加到收藏夹

Article Engineering, Mechanical

Influence of both friction and wear on the vibration of marine water lubricated rubber bearing

Huanjie Wang et al.

WEAR (2017)

添加到收藏夹

Article Chemistry, Analytical

The Analysis of Three-Body Contact Temperature under the Different Third Particle Size, Density, and Value of Friction

Horng-Wen Wu et al.

MICROMACHINES (2017)

添加到收藏夹

Article Thermodynamics

Improvement of the damping capacity of the linear damper with an oil groove in the linear guideway system

Nan Ke et al.

ADVANCES IN MECHANICAL ENGINEERING (2017)

添加到收藏夹

Article Acoustics

Piston scuffing fault and its identification in an IC engine by vibration analysis

Ashkan Moosavian et al.

APPLIED ACOUSTICS (2016)

添加到收藏夹

Article Engineering, Mechanical

Experimental observation of cross correlation between tangential friction vibration and normal friction vibration in a running-in process

Ting Liu et al.

TRIBOLOGY INTERNATIONAL (2016)

添加到收藏夹

Article Engineering, Mechanical

Effects of vibration frequency and amplitude on friction reduction and wear characteristics of silicon

Shin-Sung Yoo et al.

TRIBOLOGY INTERNATIONAL (2016)

添加到收藏夹

Article Engineering, Mechanical

Experimental investigation of the effect of in-plane vibrations on friction for different materials

Peng Wang et al.

TRIBOLOGY INTERNATIONAL (2016)

添加到收藏夹

Article Engineering, Chemical

The Relationship Between Friction and Film Thickness in EHD Point Contacts in the Presence of Longitudinal Roughness

Johan Guegan et al.

TRIBOLOGY LETTERS (2016)

添加到收藏夹

Article Acoustics

Experimental investigations to establish correlation between Stribeck curve, specific film thickness and statistical parameters of vibration and sound signals in a spur gear system

Sang-Kwon Lee et al.

JOURNAL OF VIBRATION AND CONTROL (2016)

添加到收藏夹

Article Engineering, Mechanical

Investigation on Frictional Vibration Behavior of Tribological Pairs Under Different Wear States

Di Sun et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2015)

添加到收藏夹

Article Engineering, Mechanical

Modeling and analysis of wet friction clutch engagement dynamics

Shoaib Iqbal et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2015)

添加到收藏夹

Article Engineering, Mechanical

The effect of an oscillatory entrainment velocity on the film thickness in thermal EHL point contact

Jianjun Zhang et al.

TRIBOLOGY INTERNATIONAL (2015)

添加到收藏夹

Article Engineering, Mechanical

On the effect of surface roughness in point-contact EHL: Formulas for film thickness and asperity load

M. Masjedi et al.

TRIBOLOGY INTERNATIONAL (2015)

添加到收藏夹

Article Engineering, Mechanical

Experimental study on the chaotic attractor evolvement of the friction vibration in a running-in process

Di Sun et al.

TRIBOLOGY INTERNATIONAL (2015)

添加到收藏夹

Article

Vibration Analysis of Rolling Element Bearings Defects

H. Saruhan et al.

JOURNAL OF APPLIED RESEARCH AND TECHNOLOGY (2014)

添加到收藏夹

Article Engineering, Mechanical

Friction-induced vibration of a lubricated mechanical system

J-J. Sinou et al.

TRIBOLOGY INTERNATIONAL (2013)

添加到收藏夹

Article Engineering, Mechanical

Effects of surface texturing on friction and vibration behaviors of sliding lubricated concentrated point contacts under linear reciprocating motion

U. Sudeep et al.

TRIBOLOGY INTERNATIONAL (2013)

添加到收藏夹

Article Engineering, Chemical

Friction-Induced Vibration by Stribeck's Law: Application to Wiper Blade Squeal Noise

J. Le Rouzic et al.

TRIBOLOGY LETTERS (2013)

添加到收藏夹

Article Engineering, Mechanical

The effect of longitudinal tangential vibrations on friction and driving forces in sliding motion

Pawel Gutowski et al.

TRIBOLOGY INTERNATIONAL (2012)

添加到收藏夹

Article Engineering, Mechanical

Influence of external horizontal vibration on the coefficient of friction of aluminium sliding against stainless steel

Mohammad Asaduzzaman Chowdhury et al.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2011)

添加到收藏夹

Article Physics, Applied

Effect of materials on tribochemical reactions between hydrocarbons and surfaces

Stephen M. Hsu et al.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2006)

添加到收藏夹

Article Acoustics

The effect of friction reduction in presence of ultrasonic vibrations and its relevance to travelling wave ultrasonic motors

H Storck et al.

ULTRASONICS (2002)

添加到收藏夹

Article Engineering, Industrial

The utility of radially and ultrasonically vibrated dies in the wire drawing process

M Murakawa et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.