4.6 Article

Toward the correlation of indentation hardness in micro- and nano-scale: understanding of indentation edge behaviors in Fe-Cr alloys

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Materials Science, Multidisciplinary

Toward accurate evaluation of bulk hardness from nanoindentation testing at low indent depths

Pengcheng Zhu et al.

Summary: Estimations of bulk hardness from nanoindentation can be uncertain due to various factors, but with proper testing methods and corrections for effects like pileup, accurate predictions can be made for different materials. A study on high purity Fe and Fe-Cr alloys showed consistent results under different conditions, with pileup corrections helping to improve the accuracy of bulk hardness measurements.

MATERIALS & DESIGN (2022)

Article Multidisciplinary Sciences

Practical method to determine the effective zero-point of indentation depth for continuous stiffness measurement nanoindentation test with Berkovich tip

Diancheng Geng et al.

Summary: In nanoindentation tests, it is crucial to accurately set the zero-point of indentation depth to evaluate the hardness and elastic modulus of materials. The continuous stiffness measurement method often gives inadequate results due to the surface roughness and system vibration. This study proposes a practical method to determine the effective zero-point, improving the accuracy of test data.

SCIENTIFIC REPORTS (2022)

Article Materials Science, Multidisciplinary

Indentation size effect, geometrically necessary dislocations and pile-up effects in hardness testing of irradiated nickel

M. A. Mattucci et al.

Summary: The study compared the response of Ni irradiated with protons to the non-irradiated material, based on dislocation density, through TEM analysis and nano/micro-scale indentation tests. The results showed a bi-linear trend in the Nix-Gao model for both irradiated and non-irradiated material, indicating a transition in deformation mechanisms at the nano-scale. It was suggested that the increase in hardness observed in the irradiated material during nanoindentation could be attributed to a higher density of geometrically necessary dislocations.

ACTA MATERIALIA (2021)

Article Materials Science, Multidisciplinary

Positron annihilation study on the phase transition of thermally aged Fe-Cr binary alloys at 748K

R. Kasada et al.

PHILOSOPHICAL MAGAZINE LETTERS (2019)

Article Nanoscience & Nanotechnology

Small-scale mechanical testing on nuclear materials: bridging the experimental length-scale gap

Peter Hosemann

SCRIPTA MATERIALIA (2018)

Review Engineering, Chemical

Indentation Hardness Measurements at Macro-, Micro-, and Nanoscale: A Critical Overview

Esteban Broitman

TRIBOLOGY LETTERS (2017)

Article Materials Science, Multidisciplinary

Berkovich nanoindentation study of monocrystalline tungsten: a crystal plasticity study of surface pile-up deformation

W. Z. Yao et al.

PHILOSOPHICAL MAGAZINE (2017)

Article Materials Science, Multidisciplinary

Mechanical behaviour of fully densified silica glass under Vickers indentation

V. Keryvin et al.

ACTA MATERIALIA (2017)

Article Nanoscience & Nanotechnology

On the relationship between Vickers hardness and yield stress in Al-Zn-Mg-Cu Alloys

M. Tiryakioglu

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Article Nanoscience & Nanotechnology

Correlations between nanoindentation hardness and macroscopic mechanical properties in DP980 steels

M. D. Taylor et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Article Materials Science, Multidisciplinary

Depth Dependence of Nanoindentation Pile-Up Patterns in Copper Single Crystals

Stanislaw Kucharski et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)

Review Materials Science, Multidisciplinary

The Indentation Size Effect: A Critical Examination of Experimental Observations and Mechanistic Interpretations

George M. Pharr et al.

ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 40 (2010)

Article Materials Science, Multidisciplinary

Pile-up/sink-in of rate-sensitive nanoindentation creeping solids

A. A. Elmustafa

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2007)

Article Materials Science, Coatings & Films

Comparison of nano-indentation hardness to microhardness

LM Qian et al.

SURFACE & COATINGS TECHNOLOGY (2005)

Article Nanoscience & Nanotechnology

Indentation size effect in MgO

G Feng et al.

SCRIPTA MATERIALIA (2004)

Review Materials Science, Multidisciplinary

Scaling, dimensional analysis, and indentation measurements

YT Cheng et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2004)

Article Materials Science, Coatings & Films

A nanoindentation study of copper films on oxidised silicon substrates

D Beegan et al.

SURFACE & COATINGS TECHNOLOGY (2003)

Article Materials Science, Coatings & Films

On two indentation hardness definitions

ZY Li et al.

SURFACE & COATINGS TECHNOLOGY (2002)

Article Nanoscience & Nanotechnology

On the measurement of the nanohardness of the constitutive phases of TRIP-assisted multiphase steels

Q Furnémont et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)

Article Nanoscience & Nanotechnology

Soft films on hard substrates - nanoindentation of tungsten films on sapphire substrates

R Saha et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)