相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Mechanics analysis and predictive force models for the single-diamond grain grinding of carbon fiber reinforced polymers using CNT nano-lubricant
Teng Gao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)
Investigation on grinding-induced dynamic recrystallization behavior of 40Cr alloy steel
Yunlong Yao et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2021)
Grain refinement mechanism of metamorphic layers by abrasive grinding hardening
Cong Sun et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Visualization of microstructural mechanisms in nanocrystalline ferrite during grinding
P. Grutzmacher et al.
MATERIALS & DESIGN (2020)
Prediction of microstructure gradient distribution in machined surface induced by high speed machining through a coupled FE and CA approach
Hongguang Liu et al.
MATERIALS & DESIGN (2020)
Modelling of constitutive relationship, dynamic recrystallization and grain size of 40Cr steel during hot deformation process
Liang Chen et al.
RESULTS IN PHYSICS (2019)
Mechanism of grinding-induced burns and cracks in 20CrMnTi steel gear
Long Wang et al.
MATERIALS AND MANUFACTURING PROCESSES (2019)
The role of the austenite grain size in the martensitic transformation in low carbon steels
Carola Celada-Casero et al.
MATERIALS & DESIGN (2019)
Grain refinement mechanism of nickel-based superalloy by severe plastic deformation - Mechanical machining case
Zhirong Liao et al.
ACTA MATERIALIA (2019)
Cellular Automaton Simulation of Microstructure Evolution for Friction Stir Blind Riveting
Avik Samanta et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)
Influence of grinding parameters on surface temperature and burn behaviors of grinding rail
B. Lin et al.
TRIBOLOGY INTERNATIONAL (2018)
Prediction about ground hardening layers distribution on grinding chatter by contact stiffness
Cong Sun et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2018)
Modeling of dynamic recrystallization in white layer in dry hard cutting by finite elementcellular automaton method
Duan Chunzheng et al.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2018)
Modelling of phase transformations induced by thermo-mechanical loads considering stress-strain effects in hard milling of AISI H13 steel
Binxun Li et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Temperature and strain rate dependent deformation induced martensitic transformation and flow behavior of quenching and partitioning steels
D. Q. Zou et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Predicting microstructure and strength of maraging steels: Elemental optimisation
E. I. Galindo-Nava et al.
ACTA MATERIALIA (2016)
Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component
Mei Liu et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)
Rapid surface hardening and enhanced tribological performance of 4140 steel by friction stir processing
Cinta Lorenzo-Martin et al.
WEAR (2015)
Modeling the dynamic recrystallization in austenitic stainless steel using cellular automaton method
Fei Chen et al.
COMPUTATIONAL MATERIALS SCIENCE (2014)
Further insight into the chip formation of ferritic-pearlitic steels: Microstructural evolutions and associated thermo-mechanical loadings
C. Courbon et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2014)
Physics-Based Microstructure Simulation for Drilled Hole Surface in Hardened Steel
Ninggang Shen et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2014)
Characterizing the Mechanical Properties of the Hardened Layer Induced by Grinding-Hardening
T. Nguyen et al.
MACHINING SCIENCE AND TECHNOLOGY (2014)
A three-dimensional analytical model to predict the thermo-metallurgical effects within the surface layer during grinding and grind-hardening
T. Foeckerer et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2013)
Recrystallization of 30Cr2Ni4MoV ultra-super-critical rotor steel during hot deformation. Part III: Metadynamic recrystallization
Fei Chen et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Grinding-hardening using dry air and liquid nitrogen: Prediction and verification of temperature fields and hardened layer thickness
Thai Nguyen et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2010)
The Avrami kinetics of dynamic recrystallization
John J. Jonas et al.
ACTA MATERIALIA (2009)
Enhanced structural refinement by combining phase transformation and plastic deformation in steels
N. Tsuji et al.
SCRIPTA MATERIALIA (2009)
Grinding-hardening with liquid nitrogen: Mechanisms and technology
T. Nguyen et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Initiation of dynamic recrystallization in constant strain rate hot deformation
EI Poliak et al.
ISIJ INTERNATIONAL (2003)
Mechanical property improvement of quenchable steel by grinding
I Zarudi et al.
JOURNAL OF MATERIALS SCIENCE (2002)
Microstructural modelling of dynamic recrystallisation using an extended cellular automaton approach
R Ding et al.
COMPUTATIONAL MATERIALS SCIENCE (2002)
Grain refinement in commercial alloys due to high plastic deformations and phase transformations
OA Kaibyshev
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Coupled quantitative simulation of microstructural evolution and plastic flow during dynamic recrystallization
R Ding et al.
ACTA MATERIALIA (2001)
分享论文
