相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Influence of foam agent content and talc filler on the microcellular and mechanical properties of injection molded polypropylene and talc filled polypropylene composite foams
S. H. Yetgin et al.
JOURNAL OF CELLULAR PLASTICS (2014)
Microcellular injection molding of polypropylene and glass fiber composites with supercritical nitrogen
Zhenhao Xi et al.
JOURNAL OF CELLULAR PLASTICS (2014)
Influence of relative low gas counter pressure on melt foaming behavior and surface quality of molded parts in microcellular injection molding process
Shuai Li et al.
JOURNAL OF CELLULAR PLASTICS (2014)
Influence of the Injection-Molding Parameters on the Cellular Structure and Thermo-Mechanical Properties of Ethylene-Propylene Block Copolymer Foams
J. F. Gomez-Gomez et al.
ADVANCES IN POLYMER TECHNOLOGY (2013)
Influence of the injection moulding parameters on the microstructure and thermal properties of microcellular polyethylene terephthalate glycol foams
Jaime Francisco Gomez-Gomez et al.
JOURNAL OF CELLULAR PLASTICS (2013)
Research on the reduction of sink mark and warpage of the molded part in rapid heat cycle molding process
Xiaoxin Wang et al.
MATERIALS & DESIGN (2013)
The die turning injection (DTI) process for the fabrication of hollow parts
H. J. Lee et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2012)
Analysis of warpage and shrinkage properties of injection-molded micro gears polymer composites using numerical simulations assisted by the Taguchi method
Eghbal Hakimian et al.
MATERIALS & DESIGN (2012)
Three-dimensional thermal response and thermo-mechanical fatigue analysis for a large LCD TV frame mould in steam-assisted rapid heat cycle moulding
G. -L. Wang et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2011)
Morphology, mechanical, thermal and rheological behavior of microcellular injection molded TPO-clay nanocomposites prepared by kneader
Shyh-shin Hwang et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2011)
Micro and nano cellular amorphous polymers (PMMA, PS) in supercritical CO2 assisted by nanostructured CO2-philic block copolymers - One step foaming process
Jose Antonio Reglero Ruiz et al.
JOURNAL OF SUPERCRITICAL FLUIDS (2011)
Numerical simulation of polymer foaming process in extrusion flow
Gabriel O. Aloku et al.
CHEMICAL ENGINEERING SCIENCE (2010)
Study on the Packing Effects of External Gas-Assisted Injection Molding on Part Shrinkage in Comparison With Conventional Injection Molding
Shia-Chung Chen et al.
POLYMER ENGINEERING AND SCIENCE (2010)
Shrinkage study of textile roller molded by conventional/microcellular injection-molding process
Shyh-shin Hwang et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2008)
The dimensional stability of a microcellular injection molded gear shaft
Shyh-Shin Hwang et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2008)
Effect of Increased Weight Reduction on Shrinkage of Injection-Molded Parts Using Microcellular Foaming Process
Rizwan Zafar et al.
POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING (2008)
High-frequency proximity heating for injection molding applications
Donggang Yao et al.
POLYMER ENGINEERING AND SCIENCE (2006)
Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method
Tuncay Erzurumlu et al.
MATERIALS & DESIGN (2006)
Quantitative study of shrinkage and warpage behavior for microcellular and conventional injection molding
A Kramschuster et al.
POLYMER ENGINEERING AND SCIENCE (2005)
The effect of control factors and the effect of CaCO3 on the microcellular foam morphology
JD Yoon et al.
POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING (2005)
Study of injection molded microcellular polyamide-6 nanocomposites
MJ Yuan et al.
POLYMER ENGINEERING AND SCIENCE (2004)
Development of a hybrid solid-microcellular co-injection molding process
LS Turng et al.
INTERNATIONAL POLYMER PROCESSING (2004)
Supercritical CO2 processed polystyrene nanocomposite foams
W Strauss et al.
JOURNAL OF CELLULAR PLASTICS (2004)
分享论文
