☆ 4.7 Article

Dynamic recrystallization and precipitation in an Al-Mg-Sc alloy: effect of strain rate

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

Beneficial effects of Sc/Zr addition on hypereutectic Al-Ce alloys: Modification of primary phases and precipitation hardening

Jieyun Ye et al.

Summary: This paper investigated the effect of Sc/Zr addition on the microstructure, mechanical properties, and thermal stability of a hypereutectic cast Al-Ce alloy. The results showed that Sc and Zr addition could refine the Al11Ce3 phases and improve the mechanical properties. Furthermore, after thermal exposure, the Sc and Zr atoms formed coherent precipitates, leading to increased hardness at elevated temperatures. Therefore, Al-15Ce-(Sc-Zr) alloys offer potential in high-temperature applications.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Chemistry, Physical

Influence of Zn and/or Ag additions on microstructure and properties of Al-Mg based alloys

Cheng Guo et al.

Summary: The influence of Zn and/or Ag additions on the microstructure and properties of Al-Mg based alloys has been investigated. The addition of Zn can promote the precipitation kinetics and improve the strength of the alloys, similar to the addition of Ag.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wire arc additive manufacturing Al-5.0 Mg alloy: Microstructures and phase composition

Yanfei Geng et al.

Summary: The factors of microstructure morphology, dislocations densities, and phase composition in wire arc additive manufacture of Al-5.0 Mg products are investigated. It is found that grain size diversity along the deposition direction affects dislocation density and residual stress. Decreasing the intensity of (200) improves homogeneity. The main phases are Al and Al3Mg2, with the formation of Al2Mg and irregular-shaped precipitations.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Deformation behavior and dynamic recrystallization during hot compression in homogenized Al-6Mg-0.8Mn alloys

Yu Wang et al.

Summary: In this study, Al6Mn phases with different sizes and morphologies were achieved through homogenization, and the deformation and recrystallization behaviors induced by Al6Mn phases were investigated. The results demonstrated that proper homogenization improved the segregation and dendritic structures in the alloys and obtained Al6Mn phases beneficial for recrystallization.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

The effect of Mg and Si content on the microstructure, texture and bendability of Al-Mg-Si alloys

Zhenguo Li et al.

Summary: In this study, four model Al?Mg?Si automotive sheet alloys with different Mg and Si contents were prepared and heat treated to the same T4P temper. The influence of Mg and Si content on microstructure, crystallographic texture, tensile behavior, and bendability was investigated. It was found that increased Mg and Si content led to decreased bendability and the fracture mode was predominately transgranular.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys with various Zn/Mg ratios

Yan Zou et al.

Summary: The study investigated the effects of Zn/Mg ratios on the microstructure and mechanical properties of Al-Zn-Mg-Cu alloys aged at 150 degrees C. It was found that an increase in Zn/Mg ratios significantly accelerates the aging process, with the co-existence of T' phase and eta' phase beneficial to the high strength of the alloys.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

The response of mechanical property to the microstructure variation of an Al-Mg alloy by adding tin element

Bowei Yang et al.

Summary: The study found that adding an appropriate amount of tin (Sn) element can significantly improve the tensile properties of as-cast Al-5Mg alloys, refining the Alpha-Al grains in the alloy and forming Mg2Sn phases. Nano-sized and deformable Mg2Sn phases in the alloy can result in second phase strengthening and crack propagation inhibition effects.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural and mechanical behavior of Al-Mg-Mn-Sc-Zr alloy subjected to multi-axial forging at room temperature

Hongfeng Huang et al.

Summary: The study showed that the Al-5.5 Mg-0.3Mn-0.28c-0.1Zr alloy experienced inhibited dynamic recrystallization due to the pinning effect of AlxMn and Al-3(Sc, Zr) precipitates, resulting in a significant improvement in mechanical properties at low equivalent strain. At high equivalent strain, dislocation recombination led to the formation of grain boundaries, resulting in a noticeable structure refinement.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Recrystallization behavior of Al-Mg-Mn-Sc-Zr alloy based on two different deformation ways

Jingyu Jiang et al.

MATERIALS LETTERS (2020)

添加到收藏夹

Article Chemistry, Physical

Al3(Sc, Zr) precipitation in deformed Al-Mg-Mn-Sc-Zr alloy: Effect of annealing temperature and dislocation density

Jingyu Jiang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effects of minor Sc and Zr additions on mechanical properties and microstructure evolution of Al−Zn−Mg−Cu alloys

Quan-feng XIAO et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of initial microstructure on hot deformation behavior of Al-7.9Zn-2.7Mg-2.0Cu (wt%) alloy

Qianhao Zang et al.

MATERIALS CHARACTERIZATION (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Deformation characteristics and strain-compensated constitutive equation for AA5083 aluminum alloy under hot compression

Qing-song Dai et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behaviors and optimization of processing parameters for Alloy 602 CA

Xiaoyu Qin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution and physical-based diffusion constitutive analysis of Al-Mg-Si alloy during hot deformation

Shuhui Liu et al.

MATERIALS & DESIGN (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical property improvement of aluminum alloys with high magnesium content during continuous rheo-extrusion

Renguo Guan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Chemistry, Physical

Microstructure analysis of an Al-Zn-Mg alloy during porthole die extrusion based on modeling of constitutive equation and dynamic recrystallization

Gaojin Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of novel Al-Mg-Mn-Zr-Sc-Er alloy

A. V. Pozdniakov et al.

MATERIALS LETTERS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Al3(Sc,Zr)-based precipitates in Al-Mg alloy: Effect of severe deformation

Yu. Buranova et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Microscopy

Hardness and microstructural variation of Al-Mg-Mn-Sc-Zr alloy

Sumiha Ikeshita et al.

MICRON (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Sc on microstructure and mechanical properties of as-cast Al-Mg alloys

Shi'ang Zhou et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Review Materials Science, Multidisciplinary

A review of dynamic recrystallization phenomena in metallic materials

K. Huang et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and microstructural evolution of as-homogenized Al-6Mg-0.4Mn-0.25Sc-0.1Zr alloy during compression at elevated temperature

Hongfeng Huang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Al3(Sc,Zr) and Shear Band Formation on the Tensile Properties and Fracture Behavior of Al-Mg-Sc-Zr Alloy

Hongfeng Huang et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Dislocation density evolution of AA 7020-T6 investigated by in-situ synchrotron diffraction under tensile load

Z. Y. Zhong et al.

MATERIALS CHARACTERIZATION (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Concurrent Precipitation on Recrystallization and Evolution of the P-Texture Component in a Commercial Al-Mn Alloy

S. Tangen et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interaction of recrystallization and precipitation:: The effect of Al3SC on the recrystallization behaviour of deformed aluminium

MJ Jones et al.

ACTA MATERIALIA (2003)

添加到收藏夹

Article Chemistry, Multidisciplinary

Crystallite size distribution and dislocation structure determined by diffraction profile analysis:: principles and practical application to cubic and hexagonal crystals

T Ungár et al.

JOURNAL OF APPLIED CRYSTALLOGRAPHY (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.