☆ 4.7 Article

Ultra-low temperature spark plasma sintering of super wear-resistant hard B4C composites

SCRIPTA MATERIALIA (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Ceramics

Micromechanics of machining and wear in hard and brittle materials

Brian R. Lawn et al.

Summary: Hard and brittle solids with covalent/ionic bonding are widely used in modern manufacturing technologies, and optimizing shaping processes can reduce manufacturing time and cost while extending component longevity. However, the same processes can also contribute to wear and fatigue degradation in service. Education development of advanced finishing protocols for this class of solids requires a comprehensive understanding of damage mechanisms at small-scale contacts from a materials perspective. The role of microstructure in material removal modes is highlighted, and pathways to future research—experimental, analytical, and computational—are indicated.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and mechanical behaviour of transient liquid phase spark plasma sintered B4C-SiC-TiB2 composites from a B4C-TiSi2 system

Yang Wang et al.

Summary: Fully-dense B4C-SiC-TiB2 composites with high strength and toughness were successfully prepared through in-situ reactive spark plasma sintering using B4C and TiSi2 as raw materials. TiSi2 was confirmed as a reactive sintering additive that promoted densification, while SiC-TiB2 agglomerates played a critical role in improving toughness in the composite material.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Ceramics

Effect of 1-D and 2-D carbon-based nano-reinforcements on the dry sliding-wear behaviour of 3Y-TZP ceramics

Fernando Rodriguez-Rojas et al.

Summary: The study found that the dimensionality of carbon-based nano-reinforcements and testing conditions have a significant impact on the microstructural design of ceramic composites for tribological applications. Specifically, 3Y-TZP/rGO exhibited superior wear resistance compared to other materials, and wear resistance was found to be correlated with the formation of self-lubricating tribofilms rather than hardness or toughness.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Transient liquid-phase assisted spark-plasma sintering and dry sliding wear of B4C ceramics fabricated from B4C nanopowders

Cristina Ojalvo et al.

Summary: An ultrafine-grained B4C composite with superior wear resistance was developed through fabrication, microstructural characterization, and mechanical and tribological testing. The study optimized the preparation process, identified the optimal sintering parameters, investigated the wear behavior, and compared it with a reference fine-grained B4C composite, demonstrating the potential for fabricating B4C tribocomponents with greater superior wear resistance.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Aqueous tape casting of super-hard B4C laminates with rGO-enriched reinforcing interlayers

Cristina Ojalvo et al.

Summary: Superhard B4C parts with microarchitectures composed of ceramic layers and evenly-spaced rGO-enriched reinforcing interlayers were successfully fabricated for the first time in this study. The multilayered laminates produced through aqueous colloidal processing and coating techniques demonstrated excellent hardness and crack propagation resistance.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Ultra-low wear B4C-SiC-MoB2 composites fabricated at lower temperature from B4C with MoSi2 additives

Victor Zamora et al.

Summary: Through transient liquid-phase-assisted spark-plasma sintering at lower temperature and higher MoSi2 content, superhard B4C-SiC-MoB2 triplex-particulate composites with a hardness of around 33 GPa were successfully fabricated, demonstrating excellent wear resistance properties.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fracture, fatigue, and sliding-wear behavior of nanocomposites of alumina and reduced graphene-oxide

Qizhong Wang et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Ceramics

Manufacturing B4C parts with Ti-Al intermetallics by aqueous colloidal processing

Cristina Ojalvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Processing of orthotropic and isotropic superhard B4C composites reinforced with reduced graphene oxide

Cristina Ojalvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Highly sliding-wear resistant B4C composites fabricated by spark-plasma sintering with Ti-Al additives

Angel L. Ortiz et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Ceramics

Pressureless ultrafast sintering of near-net-shaped superhard isotropic B4C/rGO composites with Ti-Al additives

Cristina Ojalvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Improving the dry sliding-wear resistance of B4C ceramics by transient liquid-phase sintering

Cristina Ojalvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Fabricating toughened super-hard B4C composites at lower temperature by transient liquid-phase assisted spark plasma sintering with MoSi2 additives

Cristina Ojalvo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Effect of sintering duration on the sliding-wear resistance of 3Y-TZP dental ceramics

Javier Alonso et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2019)

添加到收藏夹

Review Materials Science, Ceramics

The effect of oxide, carbide, nitride and boride additives on properties of pressureless sintered SiC: A review

Mandi Khodaei et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Titanium diboride-silicon carbide-boron carbide ceramics with super-high hardness and strength

Eric W. Neuman et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Fabricating geometrically-complex B4C ceramic components by robocasting and pressureless spark plasma sintering

Siamak Eqtesadi et al.

SCRIPTA MATERIALIA (2018)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and mechanical properties of B4C-TiB2-SiC composites toughened by composite structural toughening phases

Xiaorong Zhang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

添加到收藏夹

Article Materials Science, Ceramics

Near-net shape manufacture of B4C-Co and ZrC-Co composites by slip casting and pressureless sintering

Angel L. Ortiz et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

添加到收藏夹

Article Materials Science, Ceramics

Preparation of B4C composites toughened by TiB2-SiC agglomerates

Xiaorong Zhang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of Si on the microstructure and mechanical properties of spark plasma sintered boron carbide

Luoning Ma et al.

MATERIALS CHARACTERIZATION (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

High toughness and electrical discharge machinable B4C-TiB2-SiC composites fabricated at low sintering temperature

Qun Wen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Materials Science, Ceramics

Aqueous colloidal processing of near-net shape B4C-Ni cermet compacts

Fernando Rodriguez-Rojas et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

添加到收藏夹

Article Materials Science, Ceramics

Transient liquid phase spark plasma sintering of B4C-based ceramics using Ti-Al intermetallics as sintering aid

Wei Ji et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

添加到收藏夹

Article Materials Science, Ceramics

Grain size dependence of hardness and fracture toughness in pure near fully-dense boron carbide ceramics

Bibi Malmal Moshtaghioun et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

添加到收藏夹

Article Engineering, Biomedical

Mechanics of microwear traces in tooth enamel

Oscar Borrero-Lopez et al.

ACTA BIOMATERIALIA (2015)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and mechanical properties of B4C densified by spark plasma sintering with Si as a sintering aid

Sahibzada Shakir Rehman et al.

CERAMICS INTERNATIONAL (2015)

添加到收藏夹

Article Materials Science, Ceramics

Thermal shock resistance of Si3N4 and Si3N4-SiC ceramics with rare-earth oxide sintering additives

Monika Kasiarova et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)

添加到收藏夹

Article Materials Science, Ceramics

Toughening of super-hard ultra-fine grained B4C densified by spark-plasma sintering via SiC addition

B. Malmal Moshtaghioun et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

添加到收藏夹

Article Materials Science, Ceramics

Nanostructured, Infrared-Transparent Magnesium-Aluminate Spinel with Superior Mechanical Properties

Thomas Mroz et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2012)

添加到收藏夹

Article Materials Science, Ceramics

Microstructural effects on the sliding wear of transparent magnesium-aluminate spinel

Oscar Borrero-Lopez et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)

添加到收藏夹

Review Materials Science, Multidisciplinary

Synthesis and consolidation of boron carbide: a review

A. K. Suri et al.

INTERNATIONAL MATERIALS REVIEWS (2010)

添加到收藏夹

Article Materials Science, Ceramics

Superhard Boride-Carbide Particulate Composites

William G. Fahrenholtz et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2010)

添加到收藏夹

Article Materials Science, Ceramics

Microstructural design of sliding-wear-resistant liquid-phase-sintered SiC:: An overview

Oscar Borrero-Lopez et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2007)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.