相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Microstructure-Property Correlation in a Laser Powder Bed Fusion Processed High-Strength AF-9628 Steel
Priyanshi Agrawal et al.
ADVANCED ENGINEERING MATERIALS (2021)
Additive manufacturing of 24CrNiMo low alloy steel by selective laser melting: Influence of volumetric energy density on densification, microstructure and hardness
X. Cui et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
An ultra-high strength martensitic steel fabricated using selective laser melting additive manufacturing: Densification, microstructure, and mechanical properties
Raiyan Seede et al.
ACTA MATERIALIA (2020)
Inhomogeneous microstructure and its evolution of laser melting deposited 24CrNiMo steel: From single-track to bulk sample
Xueliang Rang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
The effect of different scanning strategies on microstructural evolution to 24CrNiMo alloy steel during direct laser deposition
Xuan Zhao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Microstructure evolution and gradient performance of 24CrNiMo steel prepared via laser melting deposition
Xueliang Kang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Microstructural characterization and constitutive modeling of deformation of closed-cell foams based on in situ x-ray tomography
H. W. Chai et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
The effect of carbon fiber strengthening on the mechanical properties and wear resistance of 24CrNiMo alloy steel fabricated by laser deposition
Zhihui Zhang et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Anisotropic spall behavior of CNT/2024Al composites under plate impact
J. C. Cheng et al.
CARBON (2020)
Shock and Spall in the Low-alloy Steel AF9628
Christopher Neel et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2020)
Effects of additive manufacturing on the dynamic response of AlSi10Mg to laser shock loading
M. Laurencon et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Spall strength of a mild carbon steel: Effects of tensile stress history and shock-induced microstructure
C. Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Contribution of grain size to resistance against cleavage crack propagation in ferritic steel
Fuminori Yanagimoto et al.
ACTA MATERIALIA (2019)
Process Evaluation of AISI 4340 Steel Manufactured by Laser Powder Bed Fusion
Elias Jelis et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)
Preparation and printability of 24CrNiMo alloy steel powder for selective laser melting fabricating brake disc
Chaofan Shi et al.
POWDER METALLURGY (2018)
Selective laser melting of 24CrNiMo steel for brake disc: Fabrication efficiency, microstructure evolution, and properties
Mingwei Wei et al.
OPTICS AND LASER TECHNOLOGY (2018)
Spall fracture in additive manufactured tantalum
D. R. Jones et al.
JOURNAL OF APPLIED PHYSICS (2018)
Shock and spall behaviors of a high specific strength steel: Effects of impact stress and microstructure
Wei Wang et al.
JOURNAL OF APPLIED PHYSICS (2017)
Dynamic response of AlSi10Mg alloy fabricated by selective laser melting
E. Zaretsky et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Effects of structural anisotropy on deformation and damage of a duplex stainless steel under high strain rate loading
C. Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Structure/property (constitutive and spallation response) of additively manufactured 316L stainless steel
G. T. Gray et al.
ACTA MATERIALIA (2017)
Additive manufacturing of metals
Dirk Herzog et al.
ACTA MATERIALIA (2016)
Spall fracture in additive manufactured Ti-6Al-4V
D. R. Jones et al.
JOURNAL OF APPLIED PHYSICS (2016)
Spall damage of a mild carbon steel: Effects of peak stress, strain rate and pulse duration
C. Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Multiprocess 3D printing for increasing component functionality
Eric MacDonald et al.
SCIENCE (2016)
Effect of crystallographic texture on the cleavage fracture mechanism and effective grain size of ferritic steel
A. Ghosh et al.
SCRIPTA MATERIALIA (2014)
Microstructure and cleavage in lath martensitic steels
John W. Morris et al.
SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2013)
Spall fracture: methodological aspects, mechanisms and governing factors
G. I. Kanel
INTERNATIONAL JOURNAL OF FRACTURE (2010)
Effect of microstructural refinement on the toughness of low carbon martensitic steel
Chunfang Wang et al.
SCRIPTA MATERIALIA (2008)
Crystallographic features of lath martensite in low-carbon steel
H Kitahara et al.
ACTA MATERIALIA (2006)
Spall behavior of aluminum with varying microstructures
X Chen et al.
JOURNAL OF APPLIED PHYSICS (2006)
Fundamentals of selective laser melting of alloyed steel powders
M. Rombouts et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2006)
Effect of microstructure on the cleavage fracture strength of low carbon Mn-Ni-Mo bainitic steels
YR Im et al.
JOURNAL OF NUCLEAR MATERIALS (2004)
The morphology and crystallography of lath martensite in Fe-C alloys
S Morito et al.
ACTA MATERIALIA (2003)